按官方手册推荐Innodb buffer Hit Ratios的计算是:

100-((iReads / iReadRequests)*100)

iReads : mysql->status->Innodb_buffer_pool_reads

iReadRequests: mysql->status->Innodb_buffer_pool_read_requests

出处: http://dev.mysql.com/doc/mysql-monitor/2.0/en/mem_graphref.html

搜”Hit Ratios”

推荐有兴趣的同学把这个页面都看一下应该也会有很大收获.

另外在hackmysql: www.hackmysql.com网站上的: mysqlsqlreport中关于buffer命中计算是:

$ib_bp_read_ratio = sprintf "%.2f",

($stats{'Innodb_buffer_pool_read_requests'} ?

100 - ($stats{'Innodb_buffer_pool_reads'} /

$stats{'Innodb_buffer_pool_read_requests'}) * 100 :0);

即:

ib_bp_hit=100-(Innodb_buffer_pool_reads/Innodb_buffer_pool_read_requests)*100

另外我们知道查看Innodb Buffer Hit Ratios的地方是:

复制代码 代码如下:

show engine innodb status\G;

Buffer pool hit rate : XXXX/1000;

那个XXX/1000即是buffer pool hit ratios的命中.

这样也可以从代码里看一下这个bp命中计算:

storage/innobase/buf/buf0buf.c # void buf_print_io

storage/innodbase/include/buf0buf.h #struct buf_block_struct

在buf0buf.c 中的buf_print_io函数中可以看到:

void

buf_print_io(

…

if (buf_pool->n_page_gets > buf_pool->n_page_gets_old) {

fprintf(file, "Buffer pool hit rate %lu / 1000\n",

(ulong)

(1000 - ((1000 * (buf_pool->n_pages_read

- buf_pool->n_pages_read_old))

/ (buf_pool->n_page_gets

- buf_pool->n_page_gets_old))));

} else {

fputs("No buffer pool page gets since the last printout\n",

file);

}

buf_pool->n_page_gets_old = buf_pool->n_page_gets;

buf_pool->n_pages_read_old = buf_pool->n_pages_read;

…

}

结合:

storage\innobase\include\buf0buf.h中

struct buf_block_struct{

…

ulint n_pages_read; /* number read operations */

…

ulint n_page_gets; /* number of page gets performed;

also successful searches through

the adaptive hash index are

counted as page gets; this field

is NOT protected by the buffer

pool mutex */

…

ulint n_page_gets_old;/* n_page_gets when buf_print was

last time called: used to calculate

hit rate */

…

ulint n_pages_read_old;/* n_pages_read when buf_print was

last time called */

…

从这个来看innodb buffer hit Ratios的命中计算需要本次取的值和上次值做一个减法公式应该为

ib_bp_hit=1000 – (t2.iReads – t1.iReads)/(t2.iReadRequest – t1.iReadRequest)*1000

t(n): 时间点 两个时间间隔最少是30秒以上,在小意义不大.

iReads: Innodb_buffer_pool_reads

iReadRequest: Innodb_buffer_pool_read_requests

对innodb的输出参数有兴趣的可以关注: storage/innobase/buf/Srv0srv.c 中的:

void srv_export_innodb_status()

思考:对于innodb_buffer_pool_read_requests, innodb_buffer_pool_reads这种累加值,当很大时进行: innodb_buffer_pool_reads/innodb_buffer_pool_read_requests 相来讲只能得到从开始到现在的命中率的表现了. 如果想得到现在近五分钟,近一分钟或是8点到9点每分钟的命中率情况,如果还是按着innodb_buffer_pool_reads/innodb_buffer_pool_read_requests 进行计算,只能得到mysqld开起累计在8点-9点的每分钟的累计平均命中情况.

所以如果想到每(五)分钟的命中情况,就需要本次取得的值和一(五)分钟前的值进行相减,然后进行运算.这样才能得到一个当下的bp命中情况.

两种方法没实质的对错的问题,但相对于源码中的那种计算方式更容让发现数据库的抖动问题.

能解决的问题:偶而的数据库性能抖动能直观的反应出来.

本文标题: 从MySQL的源码剖析Innodb buffer的命中率计算

本文地址: http://www.cppcns.com/shujuku/mysql/124449.html