android开发板出错,Kernel panic - not syncing: Attempted to kill the idle task!出错,求助!!!...
谢谢 kasim 我禁用后没有了那错误 可是出现了新错误 我不答明白是内核编译出错了还是别的什么?一下是启动信息 希望遇到过这问题的帮下忙 谢谢了
Copy linux kernel from 0x00060000 to 0x30008000, size = 0x00200000 ... done
zImage magic = 0x016f2818
Setup linux parameters at 0x30000100
linux command line is: "noinitrd root=/dev/mtdblock2 init=/linuxrc console=ttySAC0"
MACH_TYPE = 1999
NOW, Booting Linux......
Uncompressing Linux........................................................................................................ done, booting the kernel.
Linux version 2.6.25 (root@localhost.localdomain) (gcc version 4.3.2 (Sourcery G++ Lite 2008q3-72) ) #5 Mon May 24 16:01:13 CST 2010
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
Machine: SMDK2440
ATAG_INITRD is deprecated; please update your bootloader.
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C244X: core 405.000 MHz, memory 101.250 MHz, peripheral 50.625 MHz
S3C24XX Clocks, (c) 2004 Simtec Electronics
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: noinitrd root=/dev/mtdblock2 init=/linuxrc console=ttySAC0
irq: clearing subpending status 00000003
irq: clearing subpending status 00000002
PID hash table entries: 256 (order: 8, 1024 bytes)
timer tcon=00000000, tcnt a4ca, tcfg 00000200,00000000, usec 00001e57
Console: colour dummy device 80x30
console [ttySAC0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 61312KB available (2932K code, 497K data, 144K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 152 bytes
android_power_init
android_power_init done
NET: Registered protocol family 16
S3C2410 Power Management, (c) 2004 Simtec Electronics
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
DMA channel 0 at c4800000, irq 33
DMA channel 1 at c4800040, irq 34
DMA channel 2 at c4800080, irq 35
DMA channel 3 at c48000c0, irq 36
S3C244X: Clock Support, DVS off
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NetWinder Floating Point Emulator V0.97 (double precision)
ashmem: initialized
JFFS2 version 2.2. (NAND) 漏 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Console: switching to colour frame buffer device 30x40
fb0: s3c2410fb frame buffer device
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
s3c2440-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2440-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
brd: module loaded
loop: module loaded
dm9000 Ethernet Driver, V1.30
Uniform Multi-Platform E-IDE driver
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
BAST NOR-Flash Driver, (c) 2004 Simtec Electronics
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2440-nand s3c2440-nand: Tacls=1, 9ns Twrph0=4 39ns, Twrph1=1 9ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
NAND_ECC_NONE selected by board driver. This is not recommended !!
Scanning device for bad blocks
Creating 3 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x00000000-0x00040000 : "vivi"
0x00060000-0x00260000 : "kernel"
0x00260000-0x3ffe0000 : "yaffs2"
mtd: partition "yaffs2" extends beyond the end of device "NAND 128MiB 3,3V 8-bit" -- size truncated to 0x7da0000
usbmon: debugfs is not available
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
mice: PS/2 mouse device common for all mice
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 98 KHz
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
logger: created 64K log 'log_main'
logger: created 64K log 'log_events'
logger: created 64K log 'log_radio'
TCP cubic registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
List of all partitions:
0100 4096 ram0 (driver?)
0101 4096 ram1 (driver?)
0102 4096 ram2 (driver?)
0103 4096 ram3 (driver?)
0104 4096 ram4 (driver?)
0105 4096 ram5 (driver?)
0106 4096 ram6 (driver?)
0107 4096 ram7 (driver?)
0108 4096 ram8 (driver?)
0109 4096 ram9 (driver?)
010a 4096 ram10 (driver?)
010b 4096 ram11 (driver?)
010c 4096 ram12 (driver?)
010d 4096 ram13 (driver?)
010e 4096 ram14 (driver?)
010f 4096 ram15 (driver?)
1f00 256 mtdblock0 (driver?)
1f01 2048 mtdblock1 (driver?)
1f02 128640 mtdblock2 (driver?)
No filesystem could mount root, tried: ext3 ext2 cramfs msdos vfat romfs
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,2)
android开发板出错,Kernel panic - not syncing: Attempted to kill the idle task!出错,求助!!!...相关推荐
- VirtualBox靶机启动失败:end Kernel panic - not syncing: Attempted to kill the idle task
本专栏中所记录的问题均为个人在学习过程中偶遇的问题,大部分问题未探究原理,解决方式不一定具有普适性. 解决:在虚拟机 "设置" -> "系统" -> ...
- 解决 Virtualbox 6.1.34 出现 End kernel panic - not syncing: attempted to kill the idle task
文章目录 ❤️
- Windows 11 下 Virtualbox 6.1.34 出现 End kernel panic - not syncing: attempted to kill the idle task
前言 小半年没用 Virtualbox 了,切换到了 VMware,今天又切换回去(无聊),但是安装虚拟机出现这个错误. 解决方法 根据 Virtualbox 论坛的讨论[1]和[2],首先明确 系统 ...
- VirtualBox 安装 Ubuntu Server 出现 Kernel Panic - not syncing: Attempted to kill the idle task 问题
VirtualBox 版本:6.1.34 Ubuntu Server 版本:22.04 LTS 系统环境:Windows 11 Pro 21H2,功能中开启了"虚拟机平台"以及WS ...
- Kernel panic - not syncing:Attempted to kill...
在虚拟机中安装LINUX 系统时,出现了以下错误提示: <0>Kernel panic - not syncing:Attempted to kill the idle t ...
- linux启动根文件失败报错:进程退出exitcode,Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
进程退出的 exitcode 错误信息 内核打印 1 Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b 分 ...
- linux 开机提示 Kernel panic - not syncing: Attempted to kill init! 解决方案
原因极可能是:"在设置selinux的时候,是不是位置写错了,应该修改SELINUX行,而不是SELINUXTYPE" 问题:开机提示"Kernel panic - no ...
- Kernel panic -not syncing:Attempted to kill init!
DELL R210II安装RHEL后启动系统正常,关机再装磁盘阵列卡接好磁盘阵列,开机后CTRL+R进入界面配置RAID5. 启动后出现错误: Kernel panic -not syncing:At ...
- Linux启动提示Kernel panic - not syncing: Attempted to kill init解决办法
系统类型:CentOS 6.5(x64) 启动提示:Kernel panic - not syncing: Attempted to kill init 解决办法: 系统启动的时候,按下'e'键进入g ...
最新文章
- mysql内连接运算量会增加多少_新年手打,40道经典MYSQL面试干货,速来收藏
- j.u.c.locks.AbstractQueuedSynchronizer.Node
- MySQLFabric概述
- 计算机网络 实验教案,《计算机网络》实验教案.pdf
- 第三节: Quartz.Net五大构件之Scheduler(创建、封装、基本方法等)和Job(创建、关联等)
- 怎么测试服务器的性能,如何测试服务器性能
- iOS-项目开发1-UIImage
- poj2485(Kruskal)
- softmgr主程序_为什么我电脑打开后,我的电脑打不开,控制面板一
- OFD文件解析流程(转)
- 液压系统管路流速推荐表_液压系统中油管尺寸的选择
- 500行代码,教你用python写个微信飞机大战
- 读书笔记:重来 Rework
- oracle 闩锁(latch)概述
- 广式粤语VS港式粤语
- python日期函数
- Qt操作XML文件(创建,读,写,修改,添加,删除)
- 【较全面】LaTeX tcolorbox的使用(添加阴影,支持跨页,设置颜色,设置缩进,设置边距,设置线框类型,隐藏线框)
- vue3+vite+EChars LPL数据可视化项目总结
- 部署iis服务器与c#程序遇到的问题小结