main.c

#include <msp430.h>
#include "OLED.h"int main( void )
{WDTCTL = WDTPW + WDTHOLD;       /* Stop WDT */if ( CALBC1_8MHZ == 0xFF )      /* If calibration constant erased */{while ( 1 );               /* do not load, trap CPU!! */}DCOCTL = 0;                    /* Select lowest DCOx and MODx settings */BCSCTL1 = CALBC1_8MHZ;          /* Set range */DCOCTL   = CALDCO_8MHZ;          /* Set DCO step + modulation * / */OLED_Init();                    /* OLED初始化 */OLED_ShowString(1, 1, "ABCDEFGABCDEFG" );OLED_ShowString(2, 1, "ABCDEFGABCDEFG" );OLED_ShowString(3, 1, "ABCDEFGABCDEFG" );OLED_ShowString(4, 1, "ABCDEFGABCDEFG" );while ( 1 ){}
}

oled.h

#include "msp430g2553.h"#include "oledfont.h"void OLED_Init(void);
void OLED_Clear(void);
void OLED_ShowChar(unsigned char Line, unsigned char Column, char Char);
void OLED_ShowString(unsigned char Line, unsigned char Column, char *String);
void OLED_ShowNum(unsigned char Line, unsigned char Column, unsigned int Number, unsigned char Length);
void OLED_ShowSignedNum(unsigned char Line, unsigned char Column, unsigned int Number, unsigned char Length);
void OLED_ShowHexNum(unsigned char Line, unsigned char Column, unsigned int Number, unsigned char Length);
void OLED_ShowBinNum(unsigned char Line, unsigned char Column, unsigned int Number, unsigned char Length);// ------------------------------------------------------------
// IO口模拟I2C通信
// SCL接P2^0
// SDA接P2^1#define SCL_1 P2OUT |= BIT0
#define SCL_0 P2OUT &= ~BIT0
#define SDA_1 P2OUT |= BIT1
#define SDA_0 P2OUT &= ~BIT1#define CPU_F ( (double) 8000000)
#define delay_us( x )   __delay_cycles( (long) (CPU_F * (double) x / 1000000.0) )
#define delay_ms( x )   __delay_cycles( (long) (CPU_F * (double) x / 1000.0) )void oled_port_init(void)
{P2DIR |= BIT0 + BIT1;
}/***********OLED驱动程序用的延时程序**************/
void delay(unsigned int z)
{unsigned int x;for (x = z; x > 0; x--)delay_ms(1);
}/*** @brief  I2C开始* @param  无* @retval 无*/
void OLED_I2C_Start(void)
{SDA_1;SCL_1;SDA_0;SCL_0;
}/*** @brief  I2C停止* @param  无* @retval 无*/
void OLED_I2C_Stop(void)
{SDA_0;SCL_1;SDA_1;
}/*** @brief  I2C发送一个字节* @param  IIC_Byte 要发送的一个字节* @retval 无*/
void OLED_I2C_SendByte(unsigned char IIC_Byte)
{unsigned char i;for (i = 0; i < 8; i++){if (IIC_Byte & 0x80)SDA_1;elseSDA_0;SCL_1;SCL_0;IIC_Byte <<= 1;}SCL_1;SCL_0;
}/*** @brief  OLED写命令* @param  Command 要写入的命令* @retval 无*/
void OLED_WriteCommand(unsigned char Command)
{OLED_I2C_Start();OLED_I2C_SendByte(0x78);        //从机地址OLED_I2C_SendByte(0x00);        //写命令OLED_I2C_SendByte(Command);OLED_I2C_Stop();
}/*** @brief  OLED写数据* @param  Data 要写入的数据* @retval 无*/
void OLED_WriteData(unsigned char Data)
{OLED_I2C_Start();OLED_I2C_SendByte(0x78);        //从机地址OLED_I2C_SendByte(0x40);        //写数据OLED_I2C_SendByte(Data);OLED_I2C_Stop();
}/*** @brief  OLED设置光标位置* @param  Y 以左上角为原点，向下方向的坐标，范围：0~7* @param  X 以左上角为原点，向右方向的坐标，范围：0~127* @retval 无*/
void OLED_SetCursor(unsigned char Y, unsigned char X)
{OLED_WriteCommand(0xB0 | Y);                    //设置Y位置OLED_WriteCommand(0x10 | ((X & 0xF0) >> 4));    //设置X位置低4位OLED_WriteCommand(0x02 | (X & 0x0F));           //设置X位置高4位
}/*** @brief  OLED清屏* @param  无* @retval 无*/
void OLED_Clear(void)
{unsigned char i, j;for (j = 0; j < 8; j++){OLED_SetCursor(j, 0);for(i = 0; i < 128; i++){OLED_WriteData(0x00);}}
}/*** @brief  OLED显示一个字符* @param  Line 行位置，范围：1~4* @param  Column 列位置，范围：1~16* @param  Char 要显示的一个字符，范围：ASCII可见字符* @retval 无*/
void OLED_ShowChar(unsigned char Line, unsigned char Column, char Char)
{unsigned char i;OLED_SetCursor((Line - 1) * 2, (Column - 1) * 8);       //设置光标位置在上半部分for (i = 0; i < 8; i++){OLED_WriteData(OLED_F8x16[Char - ' '][i]);          //显示上半部分内容}OLED_SetCursor((Line - 1) * 2 + 1, (Column - 1) * 8);   //设置光标位置在下半部分for (i = 0; i < 8; i++){OLED_WriteData(OLED_F8x16[Char - ' '][i + 8]);      //显示下半部分内容}
}/*** @brief  OLED显示字符串* @param  Line 起始行位置，范围：1~4* @param  Column 起始列位置，范围：1~16* @param  String 要显示的字符串，范围：ASCII可见字符* @retval 无*/
void OLED_ShowString(unsigned char Line, unsigned char Column, char *String)
{unsigned char i;for (i = 0; String[i] != '\0'; i++){OLED_ShowChar(Line, Column + i, String[i]);}
}/*** @brief  OLED次方函数* @retval 返回值等于X的Y次方*/
unsigned int OLED_Pow(unsigned int X, unsigned int Y)
{unsigned int Result = 1;while (Y--){Result *= X;}return Result;
}/*** @brief  OLED显示数字（十进制，正数）* @param  Line 起始行位置，范围：1~4* @param  Column 起始列位置，范围：1~16* @param  Number 要显示的数字，范围：0~4294967295* @param  Length 要显示数字的长度，范围：1~10* @retval 无*/
void OLED_ShowNum(unsigned char Line, unsigned char Column, unsigned int Number, unsigned char Length)
{unsigned char i;for (i = 0; i < Length; i++){OLED_ShowChar(Line, Column + i, Number / OLED_Pow(10, Length - i - 1) % 10 + '0');}
}/*** @brief  OLED显示数字（十进制，带符号数）* @param  Line 起始行位置，范围：1~4* @param  Column 起始列位置，范围：1~16* @param  Number 要显示的数字，范围：-2147483648~2147483647* @param  Length 要显示数字的长度，范围：1~10* @retval 无*/
void OLED_ShowSignedNum(unsigned char Line, unsigned char Column, unsigned int Number, unsigned char Length)
{unsigned char i;unsigned int Number1;if (Number >= 0){OLED_ShowChar(Line, Column, '+');Number1 = Number;}else{OLED_ShowChar(Line, Column, '-');Number1 = -Number;}for (i = 0; i < Length; i++){OLED_ShowChar(Line, Column + i + 1, Number1 / OLED_Pow(10, Length - i - 1) % 10 + '0');}
}/*** @brief  OLED显示数字（十六进制，正数）* @param  Line 起始行位置，范围：1~4* @param  Column 起始列位置，范围：1~16* @param  Number 要显示的数字，范围：0~0xFFFFFFFF* @param  Length 要显示数字的长度，范围：1~8* @retval 无*/
void OLED_ShowHexNum(unsigned char Line, unsigned char Column, unsigned int Number, unsigned char Length)
{unsigned char i, SingleNumber;for (i = 0; i < Length; i++){SingleNumber = Number / OLED_Pow(16, Length - i - 1) % 16;if (SingleNumber < 10){OLED_ShowChar(Line, Column + i, SingleNumber + '0');}else{OLED_ShowChar(Line, Column + i, SingleNumber - 10 + 'A');}}
}/*** @brief  OLED显示数字（二进制，正数）* @param  Line 起始行位置，范围：1~4* @param  Column 起始列位置，范围：1~16* @param  Number 要显示的数字，范围：0~1111 1111 1111 1111* @param  Length 要显示数字的长度，范围：1~16* @retval 无*/
void OLED_ShowBinNum(unsigned char Line, unsigned char Column, unsigned int Number, unsigned char Length)
{unsigned char i;for (i = 0; i < Length; i++){OLED_ShowChar(Line, Column + i, Number / OLED_Pow(2, Length - i - 1) % 2 + '0');}
}/*** @brief  OLED初始化* @param  无* @retval 无*/
void OLED_Init(void)
{delay_ms(500);oled_port_init();           //端口初始化OLED_WriteCommand(0xAE);    //关闭显示OLED_WriteCommand(0xD5);    //设置显示时钟分频比/振荡器频率OLED_WriteCommand(0x80);OLED_WriteCommand(0xA8);    //设置多路复用率OLED_WriteCommand(0x3F);OLED_WriteCommand(0xD3);    //设置显示偏移OLED_WriteCommand(0x00);OLED_WriteCommand(0x40);    //设置显示开始行OLED_WriteCommand(0xA1);    //设置左右方向，0xA1正常 0xA0左右反置OLED_WriteCommand(0xC8);    //设置上下方向，0xC8正常 0xC0上下反置OLED_WriteCommand(0xDA);    //设置COM引脚硬件配置OLED_WriteCommand(0x12);OLED_WriteCommand(0x81);    //设置对比度控制OLED_WriteCommand(0xCF);OLED_WriteCommand(0xD9);    //设置预充电周期OLED_WriteCommand(0xF1);OLED_WriteCommand(0xDB);    //设置VCOMH取消选择级别OLED_WriteCommand(0x30);OLED_WriteCommand(0xA4);    //设置整个显示打开/关闭OLED_WriteCommand(0xA6);    //设置正常/倒转显示OLED_WriteCommand(0x8D);    //设置充电泵OLED_WriteCommand(0x14);OLED_WriteCommand(0xAF);    //开启显示OLED_Clear();               //OLED清屏
}

oledfont.h

#ifndef __OLEDFONT_H
#define __OLEDFONT_H/*OLED字模库，宽8像素，高16像素*/
const unsigned char  OLED_F8x16[][16]=
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//  00x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x33,0x30,0x00,0x00,0x00,//! 10x00,0x10,0x0C,0x06,0x10,0x0C,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//" 20x40,0xC0,0x78,0x40,0xC0,0x78,0x40,0x00,0x04,0x3F,0x04,0x04,0x3F,0x04,0x04,0x00,//# 30x00,0x70,0x88,0xFC,0x08,0x30,0x00,0x00,0x00,0x18,0x20,0xFF,0x21,0x1E,0x00,0x00,//$ 40xF0,0x08,0xF0,0x00,0xE0,0x18,0x00,0x00,0x00,0x21,0x1C,0x03,0x1E,0x21,0x1E,0x00,//% 50x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00,0x1E,0x21,0x23,0x24,0x19,0x27,0x21,0x10,//& 60x10,0x16,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//' 70x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00,0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00,//( 80x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00,0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00,//) 90x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00,0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00,//* 100x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x1F,0x01,0x01,0x01,0x00,//+ 110x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xB0,0x70,0x00,0x00,0x00,0x00,0x00,//, 120x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,//- 130x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,//. 140x00,0x00,0x00,0x00,0x80,0x60,0x18,0x04,0x00,0x60,0x18,0x06,0x01,0x00,0x00,0x00,/// 150x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00,//0 160x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//1 170x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00,//2 180x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00,0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00,//3 190x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00,//4 200x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00,//5 210x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00,//6 220x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,//7 230x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00,//8 240x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00,//9 250x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,//: 260x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x60,0x00,0x00,0x00,0x00,//; 270x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00,0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00,//< 280x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x00,//= 290x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00,//> 300x00,0x70,0x48,0x08,0x08,0x08,0xF0,0x00,0x00,0x00,0x00,0x30,0x36,0x01,0x00,0x00,//? 310xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00,0x07,0x18,0x27,0x24,0x23,0x14,0x0B,0x00,//@ 320x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20,//A 330x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00,//B 340xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00,0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00,//C 350x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00,0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00,//D 360x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00,//E 370x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00,//F 380xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00,0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00,//G 390x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20,//H 400x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//I 410x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00,//J 420x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00,0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00,//K 430x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00,//L 440x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00,0x20,0x3F,0x00,0x3F,0x00,0x3F,0x20,0x00,//M 450x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08,0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00,//N 460xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00,//O 470x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00,0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00,//P 480xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x18,0x24,0x24,0x38,0x50,0x4F,0x00,//Q 490x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00,0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20,//R 500x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00,0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00,//S 510x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//T 520x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//U 530x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00,//V 540xF8,0x08,0x00,0xF8,0x00,0x08,0xF8,0x00,0x03,0x3C,0x07,0x00,0x07,0x3C,0x03,0x00,//W 550x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08,0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20,//X 560x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//Y 570x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00,0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00,//Z 580x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00,//[ 590x00,0x0C,0x30,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00,//\ 600x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00,//] 610x00,0x00,0x04,0x02,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//^ 620x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,//_ 630x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//` 640x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x19,0x24,0x22,0x22,0x22,0x3F,0x20,//a 650x08,0xF8,0x00,0x80,0x80,0x00,0x00,0x00,0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00,//b 660x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00,//c 670x00,0x00,0x00,0x80,0x80,0x88,0xF8,0x00,0x00,0x0E,0x11,0x20,0x20,0x10,0x3F,0x20,//d 680x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x22,0x13,0x00,//e 690x00,0x80,0x80,0xF0,0x88,0x88,0x88,0x18,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//f 700x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00,//g 710x08,0xF8,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//h 720x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//i 730x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,//j 740x08,0xF8,0x00,0x00,0x80,0x80,0x80,0x00,0x20,0x3F,0x24,0x02,0x2D,0x30,0x20,0x00,//k 750x00,0x08,0x08,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//l 760x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F,//m 770x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//n 780x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//o 790x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00,0x80,0xFF,0xA1,0x20,0x20,0x11,0x0E,0x00,//p 800x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x0E,0x11,0x20,0x20,0xA0,0xFF,0x80,//q 810x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00,//r 820x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00,//s 830x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00,//t 840x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20,//u 850x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x00,0x01,0x0E,0x30,0x08,0x06,0x01,0x00,//v 860x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80,0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00,//w 870x00,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x31,0x2E,0x0E,0x31,0x20,0x00,//x 880x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x80,0x81,0x8E,0x70,0x18,0x06,0x01,0x00,//y 890x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00,//z 900x00,0x00,0x00,0x00,0x80,0x7C,0x02,0x02,0x00,0x00,0x00,0x00,0x00,0x3F,0x40,0x40,//{ 910x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,//| 920x00,0x02,0x02,0x7C,0x80,0x00,0x00,0x00,0x00,0x40,0x40,0x3F,0x00,0x00,0x00,0x00,//} 930x00,0x06,0x01,0x01,0x02,0x02,0x04,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//~ 94
};#endif

【单片机】MSP430单片机，1.3寸 IIC OLED ，显示驱动相关推荐

51单片机 IIC OLED屏幕驱动+Proteus仿真+实物验证示例程序
51单片机 IIC OLED屏幕驱动+Proteus仿真+实物验证示例程序 Proteus仿真效果注意点击运行仿真后,图像刷新出来比较慢. 示例主程序 #include "REG51.h& ...
1.3寸IIC OLED SH1106和Arduino库的适配性鸡肋问题
1.3寸IIC OLED SH1106和Arduino库的适配性鸡肋问题在还没有购买或者有购买意向的小伙伴,要注意一下,选购OLED屏幕的时候注意考量自己需求以及用途,不然买回来发现用不了,那就是一 ...
1.3寸IIC OLED SSD1106控制的oled显示问题解决方案
1.3寸IIC OLED SSD1106 控制的oled显示问题解决方案首先鸣谢:电子发烧友论坛帖子和1.3寸OLED IIC驱动右方出现两列像素白边的解决方法 1.3和0.96oled图形库显示资 ...
STM32F103C8T6在Arduino框架下驱动SH1106 1.3“ IIC OLED显示
STM32F103C8T6在Arduino框架下驱动SH1106 1.3" IIC OLED显示效果展示: 相关篇<STM32duino开发的底层驱动程序-bootloader> ...
(HAL库学习8)STM32CubeMX 驱动0.96寸IIC oled(取字模，取图模)
这一篇讲解用STM32CubeMX来使用0.96寸的IIC oled(128*64,VCC,GND,SCL,SDA四脚) 这篇文章我重新写了,如果你是第二次读到这篇文章,对不起,之前卧病额米有讲清楚, ...
1.3寸 SH1106 OLED 屏幕驱动基于stm32
1.前言最近公司使用了一块用SH1106驱动的OLED 屏幕,但是发现网上的OLED大部分都是基于ssd1306驱动芯片的,关于SH1106的资料比较少,因此将自己使用过程中遇到的问题写下来. 2. ...
利用51单片机+0.96寸iic接口oled显示图片或动图
利用51单片机+0.96寸iic接口oled显示图片或动图前言:之前讲过如何使用oled显示数字以及字符,但并未讲述如何显示BMP格式的图片, 这篇将在之前的基础上加以封装一些函数用来显示图片硬件 ...
STC15W408AS单片机IIC驱动0.96寸OLED显示
STC15W408AS单片机IIC驱动0.96寸OLED显示不同页的滚动效果() 全页的滚动效果 STC15W408AS最新系统板注意图片上的0欧姆电阻贴错了位置,应该是与GND相连的,图片上是P ...
51单片机 IIC OLED驱动显示通用程序模板
51单片机 IIC OLED驱动显示通用程序模板本模板是通过中景园OLED屏幕资料中提取保留ASCII字符集,点阵大小:6x8和8X16. 汉字取模方式取模软件:pctolcd2002 /汉字取模 ...

【单片机】MSP430单片机，1.3寸 IIC OLED ，显示驱动

文章目录

main.c

oled.h

oledfont.h

【单片机】MSP430单片机，1.3寸 IIC OLED ，显示驱动相关推荐

最新文章

热门文章