CE6870 添加ipv6 策略路由失败问题解决

问题

acl ipv6 number 3050
 rule 5 permit ipv6 destination FC00::7001:0/118
#
traffic classifier k_c1 type orif-match ipv6 acl 3050
#
traffic behavior k_b1
 redirect ipv6 nexthop FC00::48:174
#
traffic policy k_p1classifier k_c1 behavior k_b1 precedence 5
#
interface Eth-Trunk13undo portswitchipv6 enableip address 60.1.40.1 255.255.255.0ipv6 address FC00::1/112traffic-policy k_p1 inbound
#
display traffic-policy applied-record
Total records : 1
-------------------------------------------------------------------------------
Policy Type/Name                 Apply Parameter             Slot   State
-------------------------------------------------------------------------------
k_p1                             Eth-Trunk13 inbound            1   fail(4)
-------------------------------------------------------------------------------
Fail reason:
   4 -- Insufficient ACL resources.Error: Failed to apply the traffic policy k_p1 on slot 1. To check the cause, run the display traffic-policy applied-record command.# display version
Huawei Versatile Routing Platform Software
VRP (R) software, Version 8.120 (CE6870EI V200R001C00SPC700)
Copyright (C) 2012-2016 Huawei Technologies Co., Ltd.
HUAWEI CE6870-48S6CQ-EI uptime is 0 day, 1 hour, 7 minutes
Patch Version: V200R001SPH007

添加ipv6 策略路由失败，报Insufficient ACL resources
同样版本的另外一台CE6870就没有问题

解决

在尝试N次后，手动编辑一个CE6870的配置，清空所有，只保留管理口配置. 通过ftp get 引用后重启，居然解决了。只是仍未发现问题在哪里。-_-

ftp get host-ip x.x.x.x username xxxx soure xx.cfg
startup saved-configuration xx.cfg
reboot

配置

#
sysname HUAWEI
#
device board 1 board-type CE6870-48S6CQ-EI
#
drop-profile default
#
dcb pfc
#
dcb ets-profile default
#
undo anti-attack abnormal enable
undo anti-attack fragment enable
undo anti-attack icmp-flood enable
undo anti-attack tcp-syn enable
undo anti-attack udp-flood enable
#
arp learning strict
#
telnet ipv6 server disable
#
observe-port 1 interface 10GE1/0/31
#
diffserv domain default
##authentication-scheme default#authorization-scheme default#accounting-scheme default#domain default#domain default_admin
#
stack
#
interface MEth0/0/0ip address 192.168.1.243 255.255.255.0
#
interface 10GE1/0/1device transceiver 10GBASE-FIBER
#
interface 10GE1/0/2device transceiver 10GBASE-FIBER
#
interface 10GE1/0/3
#
interface 10GE1/0/4
#
interface 10GE1/0/5device transceiver 10GBASE-FIBER
#
interface 10GE1/0/6device transceiver 10GBASE-FIBER
#
interface 10GE1/0/7device transceiver 10GBASE-FIBER
#
interface 10GE1/0/8device transceiver 10GBASE-FIBER
#
interface 10GE1/0/9
#
interface 10GE1/0/10
#
interface 10GE1/0/11device transceiver 10GBASE-FIBER
#
interface 10GE1/0/12
#
interface 10GE1/0/13
#
interface 10GE1/0/14
#
interface 10GE1/0/15device transceiver 10GBASE-FIBER
#
interface 10GE1/0/16device transceiver 10GBASE-FIBER
#
interface 10GE1/0/17device transceiver 10GBASE-FIBER
#
interface 10GE1/0/18device transceiver 10GBASE-FIBER
#
interface 10GE1/0/19device transceiver 1000BASE-X
#
interface 10GE1/0/20device transceiver 1000BASE-X
#
interface 10GE1/0/21device transceiver 10GBASE-FIBER
#
interface 10GE1/0/22device transceiver 10GBASE-FIBER
#
interface 10GE1/0/23device transceiver 10GBASE-FIBER
#
interface 10GE1/0/24device transceiver 10GBASE-FIBER
#
interface 10GE1/0/25device transceiver 10GBASE-FIBER
#
interface 10GE1/0/26device transceiver 10GBASE-FIBER
#
interface 10GE1/0/27device transceiver 10GBASE-FIBER
#
interface 10GE1/0/28device transceiver 10GBASE-FIBER
#
interface 10GE1/0/29device transceiver 10GBASE-FIBER
#
interface 10GE1/0/30device transceiver 10GBASE-FIBER
#
interface 10GE1/0/31device transceiver 10GBASE-FIBER
#
interface 10GE1/0/32device transceiver 1000BASE-X
#
interface 10GE1/0/33device transceiver 10GBASE-FIBER
#
interface 10GE1/0/34
#
interface 10GE1/0/35device transceiver 10GBASE-FIBER
#
interface 10GE1/0/36loopback-detect enable
#
interface 10GE1/0/37device transceiver 10GBASE-FIBER
#
interface 10GE1/0/38
#
interface 10GE1/0/39device transceiver 10GBASE-FIBER
#
interface 10GE1/0/40device transceiver 10GBASE-FIBER
#
interface 10GE1/0/41
#
interface 10GE1/0/42device transceiver 10GBASE-FIBER
#
interface 10GE1/0/43device transceiver 10GBASE-FIBER
#
interface 10GE1/0/44device transceiver 10GBASE-FIBER
#
interface 10GE1/0/45device transceiver 10GBASE-FIBER
#
interface 10GE1/0/46device transceiver 10GBASE-FIBER
#
interface 10GE1/0/47device transceiver 10GBASE-FIBER
#
interface 10GE1/0/48device transceiver 10GBASE-FIBER
#
interface 100GE1/0/1
#
interface 100GE1/0/2
#
interface 100GE1/0/3
#
interface 100GE1/0/4
#
interface 100GE1/0/5
#
interface 100GE1/0/6
#
interface NULL0
#
ssh authorization-type default aaa
#
vm-manager
#
return

CE6870 添加ipv6 策略路由失败问题解决相关推荐

Linux 添加IPv6策略路由,基于策略的路由通过IPv6配置示例
基于策略的路由为表示和实现转发提供一机制/根据策略的路由数据包定义由网络管理员.基于策略的路由应用到流入数据包并且使用路由映射定义策略.基于在路由映射定义的标准,数据包转发/路由对适当的下一跳.本文为 ...
VS +QT 手动添加Q_OBJECT 报错问题解决
VS+QT 手动添加Q_OBJECT 报错问题解决参考QT Ide上,需要重新Qmake 在vs上,手动添加Q_OBJECT,后moc_XXX文件也生成,但是编译却失败,出现无法打开moc_xxx ...
Kubernetes 纳管节点卡住导致加入集群失败问题解决
问题现象之前自己搭建了一个k8s集群,配置如下: os: centos8 master: 8U8G 192.168.2.106 worker1: 4U4G 192.168.2.240 worker2 ...
LINUX学习笔记1 网卡配置（网络适配器安装失败问题解决）
LINUX学习笔记1 网卡配置(网络适配器安装失败问题解决) 概述每一次选修课总会碰到一堆问题,我真的是幸运得很.这次是LINUX服务器管理这门课,最开始安装虚拟机一切正常(用的是VMware安装u ...
shiro realm 注解失败问题解决过程
shiro realm 注解失败问题解决过程参考文章: (1)shiro realm 注解失败问题解决过程 (2)https://www.cnblogs.com/ASPNET2008/p/55072 ...
xmanager 开启X11转发失败问题解决
xmanager 开启X11转发失败问题解决参考文章: (1)xmanager 开启X11转发失败问题解决 (2)https://www.cnblogs.com/xuelangos/p/107862 ...
MariaDB 修改存储路径后启动失败问题解决
MariaDB 修改存储路径后启动失败问题解决参考文章: (1)MariaDB 修改存储路径后启动失败问题解决 (2)https://www.cnblogs.com/dizhiyaochang/p/ ...
Linux入门实践笔记（七）——云服务器中配置Java项目的JMX连接失败问题解决记录
Linux入门实践笔记(七)--云服务器中配置Java项目的JMX连接失败问题解决记录参考文章: (1)Linux入门实践笔记(七)--云服务器中配置Java项目的JMX连接失败问题解决记录 (2) ...
记录sqoop同步失败问题解决过程，过程真的是很崎岖。(1月6日解决)
记录sqoop同步失败问题解决过程,过程真的是很崎岖.(1月6日解决) 参考文章: (1)记录sqoop同步失败问题解决过程,过程真的是很崎岖.(1月6日解决) (2)https://www.cnbl ...
pip 更新版本失败问题解决
pip 更新版本失败问题解决参考文章: (1)pip 更新版本失败问题解决 (2)https://www.cnblogs.com/math98/p/11588228.html (3)https:// ...

CE6870 添加ipv6 策略路由失败问题解决

CE6870 添加ipv6 策略路由失败问题解决

问题

解决

CE6870 添加ipv6 策略路由失败问题解决相关推荐

最新文章

热门文章