5G场强测试关键指标

*REFERENCE:********5G NR*

[外链图片转存失败,源站可能有防盗链机制,建议将图片保存下来直接上传(img-I4UXz3Yh-1591947841851)(file:///C:\Users\ybb\AppData\Local\Temp\ksohtml18180\wps18.jpg)]

FIGURE 6.17

In most wireless communication systems, the device can be in different states depending on the traffic activity. This is true also for NR and an NR device can be in one of three RRC states, RRC_IDLE, RRC_ACTIVE, and RRC_INACTIVE.

The first two RRC states, RRC_IDLE and RRC_CONNECTED,are similar to the counterparts in LTE, while RRC_INACTIVE is a new state introduced in NR and not present in the original LTE design. There are also corenetwork states not discussed further herein, CN_IDLE and CN_CONNECTED,

depending on whether the device has established a connection with the core network or not.

*REFERENCE:TS********38********.********215*

*LTE—R场强测试方法研究********-魏来*

*Key indicators of the field strength measurements：*

intra-frequency cell:

inter-frequency cell:

inter-RAT cell:

SS-RSRP:

Applicable for：All

Definition：SS-RSRP is defined as the linear average over the power contributions of the resource that carry SSS.

Name	Applicable State	Definition
SS-RSRP	ALL	SS-RSRP is defined as the linear average over the power contributions of the resource that carry SSS.
CSI-RSRP	RRC_CONNECTED	CSI-RSRP is defined as the linear average over the power contributions of the resource elements that carry CSI reference signals configured for RSRP measurements within the considerated measurement frequency bandwidth in the configured CSI-RS occassions.
SS-RSRQ	ALL	SS-RSRQ is defined as the ratio of N*SS-RSRP/NR carrier RSSI.
CSI-RSRQ	RRC_CONNECTED	CSI-RSRQ is defined as the ratio of N*CSI-RSRP/CSI-RSSI
SS-SINR	RRC_CONNECTED	SS-SINR is defined as the linear average over the power contribution of the resource elements carrying secondary synchronization signals divided by the linear average of the noise and interference power contribution over the resource elements carrying secondary synchronization signals within the same frequency bandwidth.
CSI-SINR	RRC_CONNECTED	CSI-SINR is defined as the linear average over the power contribution of the resource elements carrying CSI reference signials divided by the linear average of the noise and interference power contribution over the resource elements carrying CSI reference signals within the same frequency bandwidth.
RSSI	inter-RAT

*REFERENCE:*

*3GPP TS 38.213:5G NR; Physical layer procedures for control channels*

*3GPP TS 38.214: 5G NR; Physical layer procedures for data channels*

*3GPP TS 38.215: 5G NR; Physical layer measurements*

*Key indicators of the field strength measurements：*

In LTE, the UE measurements are done for RSRP, RSRQ and SNR associated with CRS (Cell Specific Reference Signal) .5G NR uses SS (Synchronization Signal) and CSI (Channel State Information) instead of CRS, so 3GPP had put new definitions for UE measurements in place, and some of these are discussed below.

· For FR-1, the reference point for the measurement shall be the antenna connector of the UE.

· For FR-2, it shall be measured based on the combined signal from antenna elements corresponding to a given receiver branch.

（whether 5G-R will consider high frequency？）

****SS-RSRP****: SS-RSRP stands for Synchronization Signal reference signal received power. It is defined as the linear average over the power contributions (in Watt) of the resource elements that carry SSS. The measurement time resource for SS-RSRP are confined within SS/PBCH Block Measurement Time Configuration (SMTC) window duration.

For SS-RSRP determination, demodulation reference signals for PBCH and, if indicated by higher layers, CSI RS in addition to SSS may be used.SS-RSRP using demodulation reference signal for PBCH or CSI reference signal shall be measured by linear averaging over the power contributions of the resource elements that carry corresponding reference signals taking into account power scaling for the reference signals. This measurement is applicable for following:

· RRC_CONNECTED intra-frequency

· RRC_IDLE intra-frequency

· RRC_IDLE inter-frequency

· RRC_INACTIVE intra-frequency

· RRC_INACTIVE inter-frequency

· RRC_CONNECTED intra-frequency

· RRC_CONNECTED inter-frequency

****CSI-RSRP****: CSI-RSRP stands for CSI reference signal received power. It is defined as the linear average over the power contributions (in watt) of the resource elements that carry CSI-RS configured for RSRP measurements within the considered measurement frequency bandwidth in the configured CSI-RS occasions. For CSI-RSRP determination CSI reference signals transmitted on antenna port 3000 shall be used, if CSI_RSRP is used for L1-RSRP, CSI reference signals transmitted on antenna ports 3000, 3001 can be used.

For intra-frequency CSI-RSRP measurements, if the measurement gap is not configured, UE is not expected to measure the CSI-RS resource outside of the active downlink bandwidth part. CSI-RSRP measurement is applicable for following:

· If CSI-RSRP is used for L1-RSRP, RRC_CONNECTED intra-frequency.
Otherwise,

· RRC_CONNECTED intra-frequency,

· RRC_CONNECTED inter-frequency

****NR-RSSI****: NR-RSSI stands for NR carrier Received Signal Strength Indicator, it comprises the linear average of the total received power (in Watt) observed only in certain OFDM symbols of measurement time resource, in the measurement bandwidth, over N number of resource blocks from all sources, including co-channel serving and non-serving cells, adjacent channel interference, thermal noise etc. The measurement time resource for NR Carrier RSSI are confined within SS/PBCH Block Measurement Time Configuration (SMTC) window duration.

· For intra-frequency measurements, NR Carrier RSSI is measured with timing reference corresponding to the serving cell in the frequency layer

· For inter-frequency measurements, NR Carrier RSSI is measured with timing reference corresponding to any cell in the target frequency layer

****CSI-RSSI****: CSI-RSSI stands for CSI Received Signal Strength Indicator, it comprises the linear average of the total received power (in Watt) observed only in OFDM symbols of measurement time resource, in the measurement bandwidth, over N number of resource blocks from all sources, including co-channel serving and non-serving cells, adjacent channel interference, thermal noise etc. The measurement time resource for CSI-RSSI corresponds to OFDM symbols containing configured CSI-RS occasions.

****SS-RSRQ****: SS-RSRQ stands for Secondary synchronization Signal Reference Signal Received Quality. It is defined as the ratio of N×SS-RSRP /NR carrier RSSI, where N is the number of resource blocks in the NR carrier RSSI measurement bandwidth. The measurements in the numerator and denominator shall be made over the same set of resource blocks. SS-RSRQ measurement is applicable for following:

· RRC_IDLE intra-frequency

· RRC_IDLE inter-frequency

· RRC_INACTIVE intra-frequency

· RRC_INACTIVE inter-frequency

· RRC_CONNECTED intra-frequency

· RRC_CONNECTED inter-frequency

****CSI-RSRQ****: is defined as the ratio of N×CSI-RSRP to CSI-RSSI, where N is the number of resource blocks in the RSSI measurement bandwidth. The measurements in the numerator and denominator shall be made over the same set of resource blocks. CSI-RSRQ measurement is applicable for following:

· RRC_CONNECTED intra-frequency

· RRC_CONNECTED inter-frequency

****SS-SINR****: SS-SINR stands for SS signal-to-noise and interference ratio. It is defined as the linear average over the power contribution (in Watt) of the resource elements carrying SSS divided by the linear average of the noise and interference power contribution (in Watt) over the resource elements carrying SSS within the same frequency bandwidth. SS-SINR measurement is applicable for following:

· RRC_CONNECTED intra-frequency

· RRC_CONNECTED inter-frequency

****CSI-SINR****: CSI-SINR stands for CSI signal-to-noise and interference ratio.It is defined as the linear average over the power contribution (in Watt) of the resource elements carrying CSI reference signals divided by the linear average of the noise and interference power contribution (in Watt) over the resource elements carrying CSI reference signals within the same frequency bandwidth.SS-SINR measurement is applicable for following:

· RRC_CONNECTED intra-frequency

· RRC_CONNECTED inter-frequency

source elements carrying CSI reference signals within the same frequency bandwidth.SS-SINR measurement is applicable for following:

· RRC_CONNECTED intra-frequency

· RRC_CONNECTED inter-frequency

5G场强测试关键指标相关推荐

5g的八大关键指标_你对5G技术标准了解多少（干货）
业界齐心协力打造能满足移动宽带业务和物联网业务的5G技术标准,近期国际标准组织3GPP宣布冻结第一个独立组网5G标准.5G具有大带宽.低时延.灵活配置的特点,设计全新的基于服务化系统架构,并具备网络切 ...
5g的八大关键指标_5G的七大关键性能指标5G对生活的改变新5G时代的来临身边巨变...
为什么要发展5G 21 世纪初,第四代移动通信技术开始进入人们的生活,在其支撑下的移动数据传输,计算以及多媒体运作方面的应用大大得到了发展,推动了整个世界的发展.然而,随着世界的发展,大数据时代的来临 ...
5g的八大关键指标_【一起学5G】_5G NR关键性能KPI指标
更多学习内容,欢迎关注公众号"无线网络优化" 5G NR各厂家网管性能KPI跟LTE类似,统计维度分基站级和小区级随着无线网络云化架构演进,基站的操作维护对象分为CU和DU 测量 ...
5g的八大关键指标_5G关键性能指标解析
5G 关键性能指标解析李洪城,朱峰,卢彩玲 [摘要] 摘要:针对< 5G 技术研发试验总体方案>所要求的 5G 关键性能指标,借助 IMT-2020 推进组的 5G 白皮书. IT ...
5g的八大关键指标_【技术·航天】5G与卫星通信融合应用前景浅析
在地面通信领域,中国从2G跟随者过渡成为3G突破者及4G实现同步,如今在5G时代已渐进变成引领者:在卫星通信领域,国外"星链计划".Telesat星座等跑马圈地式布局,国内鸿雁计划 ...
5g的八大关键指标_2019互联网八大热门话题：总有一个击中你的表达欲
本期全媒派通过梳理2019年头牌观点小程序上的用户热议内容,与你共同盘点中文互联网八大话题,看看流行语或流行事件背后的网民心态. 来源:全媒派南京大学新闻传播学院教授杜骏飞曾归纳了网民心理的九大 ...
5g的八大关键指标_2019百度沸点十大科技热词出炉，AI、5G、智能家居......实力霸榜！...
12月9日,百度沸点2019年度榜单启动发布. 率先发布的是"百度沸点2019年度科技热词", AI.5G.区块链.机器人.VR.AI寻人.智能家居.物联网.刷脸支付.AR十个关键 ...
稳定性测试的要点、性能测试的监控的关键指标
一.稳定性测试的要点 1.长时间的以正常的业务负载进行运行(最低为用户实际使用时的负载量,如果用户实际负载量低于最优负载量,也可以使用最优负载量). 2.稳定性的测试数据(用户实际使用负载量)来源于运 ...
我国已建立30个5G基站仪表厂商发力5G第二阶段测试
在无线领域,5G毋庸置疑是今年最大的热点,虽然距离5G商用还有几年时间,但是各国都已经开始了5G的相关测试工作.中国5G国家试验是全球最大的区域性5G试验测试项目,该项目于2016年1月全面启动,分为 ...

5G场强测试关键指标

5G场强测试关键指标相关推荐

最新文章

热门文章