测控专业英语复习资料
2024-04-22 04:12:46
测控专业英语复习资料
- 短语互译
- 第一次
- 第二次
- 第三次
- 第四次
- 长句翻译
- 第一次
- 第二次
- 第三次
- 第四次
- 论文摘要翻译
- 第一篇: Observations of offshore wind characteristics by Doppler-LiDAR for wind energy applications
- 第二篇: A survey on consumers empowerment, communication technologies, and renewable generation penetration within Smart Grid
- 第三篇: Mastering the game of Go with deep neural networks and tree search
短语互译
第一次
| 原文 | 翻译 |
|---|---|
| sensor characteristics | 传感器特性 |
| electrical supply | 供电 |
| signal conditioning unit | 信号调节单元 |
| accuracy rating | 精度等级 |
| 温度计 | thermometer |
| 速度计 | speedometer |
| dead-band characteristics | 死区特性 |
| static friction | 静摩擦 |
| full operating range of the device | 设备的全工作范围 |
| ambient temperature | 环境温度 |
| aging effect(s) | 老化效应 |
| mechanical wear | 机械磨损 |
| self-heating | 自热效应 |
| bridge-circuit | 电桥电路 |
| the smallest detectable change | 最小的可检测变化 |
| contact friction | 接触摩擦 |
| mechanical strain | 机械应变 |
| resistance temperature detector | 电阻温度检测器 |
| power dissipation | 功率损耗 |
| lead impedance | 引线阻抗 |
第二次
| 原文 | 翻译 |
|---|---|
| the rated voltage and current | 额定电压和电流 |
| gear drive | 齿轮传动 |
| micro-actuator | 微执行器 |
| a binary actuator | 二元执行器 |
| stable-state output | 稳态输出 |
| stepper motor | 步进电机 |
| small incremental motion | 小增量运动 |
| on-off type control action | 开关型控制动作 |
| a low energy level command signal | 低能级指令信号 |
| actuator load | 执行器负载 |
| thousands of horsepower motor | 千马力电机 |
| motor shaft | 电机轴 |
| synchronous motor | 同步电动机 |
| three-phase induction motor | 三相感应电动机 |
| large-horsepower application | 大马力应用 |
| two-phase motor | 两相电动机 |
| solid-state drive | 固态硬盘 |
| unipolar stepper motor | 单极步进电机 |
| bottom stator pole | 定子底极 |
| a permanent magnet with six poles | 六极永磁体 |
| counterclockwise direction | 逆时针方向 |
| a soft iron core | 柔软的铁心 |
| directional control valve | 方向控制阀 |
| hydraulic or pneumatic actuator | 液压或气动执行机构 |
| analog to digital converter | 模数转换器 |
| transfer function | 传递函数 |
| discrete output states | 离散输出状态 |
| a sample-and-hold circuit | 采样保持电路 |
| high-input impedance | 高输入阻抗 |
| the highest frequency component | 最高频率分量 |
| propagation delay | 传播延迟 |
| least significant bit | 最低有效位 |
第三次
| 原文 | 翻译 |
|---|---|
| virtual instrument | 虚拟仪器 |
| computational size, cost | 计算量，成本 |
| bulk storage | 大容量存储 |
| off-line instrument | 离线仪表 |
| data processing | 数据处理 |
| custom developed | 定制开发 |
| with the advent of microelectronics | 随着微电子技术的出现 |
| realtime application | 实时应用 |
| special/general-purpose computer | 专用/通用计算机 |
| a considerable breadth of measurement and control | 相当广泛的测量和控制 |
| industrial field | 工业领域 |
| high-speed application | 高速应用 |
| user-interface operations | 用户界面操作 |
| windows-type software | 窗口类型软件 |
| complex manipulations along with memory, look-up tables, and intelligent displays and controls | 复杂的操作以及内存、查找表、智能显示和控件 |
| large memory capacity | 大存储容量 |
| a conditioning circuit | 调节电路 |
| local area network | 局域网 |
| remote radio communication protocol | 远程无线电通信协议 |
| interconnection buses | 互连总线 |
| application software | 应用程序软件 |
| General-purpose Interface Bus | 通用接口总线 |
| Industry Standard Architecture Bus | 行业标准架构总线 |
| addressing width of a processor | 处理器的寻址宽度 |
| one-byte wide | 一字节宽 |
| a full 16-bit data bus | 完整的16位数据总线 |
| two-clock-cycle | 两个时钟周期 |
| direct memory access | 直接内存访问 |
| Plug and play | 即插即用 |
| micro-channel architecture | 微通道架构 |
| serial communication peripherals | 串行通讯外设 |
| novice users | 新手用户 |
| high-speed peer to peer communication | 高速对等通信 |
第四次
| 原文 | 翻译 |
|---|---|
| yaw damper system | 偏航阻尼系统 |
| autopilot | 自动驾驶 |
| trail-and-error | 试错法 |
| dynamic analysis | 动态分析 |
| control system design | 控制系统设计 |
| classical control theory | 经典控制理论 |
| high-speed digital computers | 高速数字计算机 |
| state variables | 状态变量 |
| open-loop control systems | 开环控制系统 |
| a negative feedback system | 负面反馈系统 |
| differential equation | 微分方程 |
| difference equation | 差分方程 |
| time interval | 时间间隔 |
| a sampled-data system | 采样数据系统 |
| nonlinear system | 非线性系统 |
| time-invariant system | 时不变系统 |
| stationary/nonstationary system | 平稳/非平稳系统 |
| time-dependent | 时间相关的 |
| lumped parameter system | 集总参数系统 |
| distributed parameter system | 分布参数系统 |
| ordinary/partial differential equation | 常/偏微分方程 |
| deterministic/stochastic system | 确定性/随机系统 |
| multi-variable system | 多变量系统 |
| single-input single-output system | 单输入单输出系统 |
| performance criteria and indices | 绩效标准和指标 |
| transient response | 瞬态响应 |
| steady-state value of the output | 输出的稳态值 |
| nonzero initial conditions | 非零初始条件 |
| complex variable in the Laplace domain | Laplace域中的复变量 |
| linearity and superposition theorems | 线性和叠加定理 |
| shifting theorem | 移位定理 |
| piecewise continuous inputs | 分段连续输入 |
| analytic function | 分析函数 |
| homogeneous/particular solution | 均匀/特殊溶液 |
| unilateral Fourier integral | 单边傅里叶积分 |
| DC-motor drive | 直流电动机驱动 |
| zero internal impedance | 零内部阻抗 |
| dc voltage source | 直流电压源 |
| Pulse-Width Modulation | 脉冲宽度调制 |
| switch duty ratio | 开关占空比 |
| a resistive load | 电阻负载 |
| uninterruptible AC power supplies | 不间断交流电源 |
| two-quadrant converter | 二象限转换器 |
| voltage/current source inverters | 电压/电流源逆变器 |
| square-wave inverter | 方波逆变器 |
| voltage cancellation | 电压抵消 |
| switch-mode converter | 开关模式转换器 |
| linear vector space | 线性向量空间 |
| power transistor | 功率晶体管 |
| very large scale integrated circuits | 超大规模集成电路 |
长句翻译
第一次
| 第一次 |
|---|
| The major reason for the availability of such equipment has been the development of computers and microprocessors which are used as sophisticated, flexible and yet low cost controllers. |
| 这种设备的可用性的主要原因是计算机和微处理器的发展，它们被用作精密、灵活且低成本的控制器。 |
| However, the operation of such systems would be very poor, if possible at all, if the computer’s decision making programs were not being supplied with suitable, up to date, quality information about the state of the external system. |
| 但是，如果没有为计算机的决策程序提供有关外部系统状态的适当的最新质量信息，那么，如果可能的话，此类系统的操作将非常糟糕。 |
| Electrical noise (i.e. unwanted signals) may be generated by variation in contact resistance, by mechanical wear due to contact fiction, and by contact vibration transmitted from the sensing element. |
| 电噪声（即不需要的信号）可能由接触电阻的变化、接触摩擦引起的机械磨损和传感元件传输的接触振动产生。 |
| When a specification refers to a dead-zone or dead-band, it is referring to the largest change in the quantity to be measured to which the output does not change, or the change of input to which there is no output. |
| 当一个规范是指一个死区或死区时，它指的是待测量中输出不变的最大变化，或是没有输出的输入变化。 |
| This means that if we take a temperature measurement with the thermometer and find it to be ±20.1°C, then the actual temperature lies somewhere between 15.9°C and 20.3°C. |
| 这意味着，如果我们用温度计测量温度，发现温度为±20.1°C，那么实际温度介于15.9°C和20.3°C之间。 |
第二次
| 第二次 |
|---|
| Actuators are basically the muscle behind a mechatronics system that accepts a control command (mostly in the form of an electrical signal) and produces a change in the physical system by generating force, motion, heat, flow, etc. |
| 执行器基本上是机电一体化系统背后的肌肉，该机电一体化系统接受控制命令（主要是电信号的形式），并通过产生力，运动，热量，流量等在物理系统中产生变化。 |
| The stepper motor is a discrete (incremental) positioning device that moves one step at a time for each pulse command input. Since they accept direct digital commands and produce a mechanical motion, the stepper motors are used widely in industrial control applications. |
| 步进电机是一种离散（增量）定位装置，每次为每个脉冲指令输入移动一步。由于步进电机接受直接的数字指令并产生机械运动，因此在工业控制应用中得到了广泛的应用。 |
| Normally, due to the spring force, the soft iron core is pushed to the extreme left position; when the solenoid is excited, the soft iron core will move to the right extreme position thus providing the electromagnetic actuation. |
| 正常情况下，由于弹簧力的作用，软铁心被推到最左边的位置；当电磁阀被激发时，软铁心会移动到最右边的位置，从而提供电磁驱动。 |
| A/D conversion is essentially a quantizing process, whereby an analog signal is represented by discrete states. |
| A / D转换本质上是量化过程，通过这个过程将模拟信号用离散状态表示。 |
| An A/D converter requires a certain amount of time, called conversion time, to change an analog signal into the corresponding digital signal. If the analog signal changes during the conversion time, the converter output may be in error. To prevent this, a sample-and-hold circuit is used to sense the analog signal at the start of conversion, and store it on a capacitor during the remaining conversion time. |
| A/D转换器需要一定的时间（称为转换时间）将模拟信号转换成相应的数字信号。如果在转换期间模拟信号发生变化，则转换器输出可能出错。为了防止这种情况，在转换开始时使用采样保持电路来检测模拟信号，并在剩余的转换时间内将其存储在电容器上。 |
第三次
| 第三次 |
|---|
| As a result, rudimental control systems were developed. Relays were attached to the instruments so that processes could respond to parametric changes. Soon, the single relay grew into more than one, allowing for multipoint control. Then, rate detectors were added and finally integrators, creating the PID control system. |
| 因此，开发了基本的控制系统。继电器连接到仪器上，以便过程能够对参数变化作出响应。很快，单继电器发展成多个，允许多点控制。然后加入速率检测器，最后加入积分器，构成PID控制系统。 |
| It became normal for a measuring instrument to accept a signal; condition the input by linearizing, shaping, band limiting, etc.; and then digitize the result. The digital output was manipulated in a special, onboard processor in order to provide control or analytical decisions. |
| 测量仪器接收信号变得正常；通过线性化、整形、频带限制等调节输入；然后将结果数字化。数字输出在一个特殊的机载处理器中进行操作，以提供控制或分析决策。 |
| At the same time, the sphere of measurement and control systems expanded from merely measuring electrical and electronics parameters to encompassing all ancillary technologies including the mechanical, chemical, civil, and medical fields. |
| 同时，测量和控制系统的范围从仅仅测量电气和电子参数扩展到包括机械、化学、民用和医疗领域在内的所有辅助技术。 |
| The speed and capability of general-purpose computers advanced exponentially. It soon became possible to adapt standard, high-speed computers to the online applications required in real time measurement and control. |
| 通用计算机的速度和功能呈指数级增长。 很快就可以使标准的高速计算机适应实时测量和控制所需的在线应用程序。 |
| With the addition of computers and computational capability, the cost of the instruments increased, How do we improve performance without adding cost? |
| 随着计算机和计算能力的增加，仪器的成本增加，如何在不增加成本的情况下提高性能？ |
| Consider what a virtual instrument and control system might contain. For a measurement instrument, there must be a sensor. If the parameter being measured is not electrical, this must incorporate a transducer to change the information to an electrical signal. |
| 考虑一下虚拟仪器和控制系统可能包含的内容。 对于测量仪器，必须有一个传感器。 如果要测量的参数不是电气参数，则必须包含一个传感器才能将信息更改为电气信号。 |
第四次
| 第四次 |
|---|
| Control systems designed by humans are used to extend their physical capabilities, to compensate for their physical limitations, to relieve them of routine or tedious tasks, or to save money. |
| 由人类设计的控制系统被用来扩展他们的物理能力，补偿他们的物理限制，减轻他们的日常或乏味的任务，或是节省资金。 |
| Freed of this routine task, the pilot can perform other tasks, such as navigation and/or communications, thus reducing the number of crew required and consequently the operating cost of the aircraft. |
| 摆脱了这一例行任务，飞行员可以执行其他任务，如导航和/或通信，从而减少所需的机组人员数量，从而降低飞机的运行成本。 |
| The definition of the transfer function requires the system to be linear and stationary, with continuous variables and with zero initial conditions. The transfer function is most useful when the system is also lumped parameter and when transport lags are absent or neglected. |
| 传递函数的定义要求系统是线性和平稳的，具有连续变量且初始条件为零。 当系统也是集总参数且缺少或忽略运输滞后时，传递函数最有用。 |
| One of the methods for controlling the output voltage employs switching at a constant frequency (hence, a constant switching time period TS=ton+toff), and adjusting the on-duration of the switch to control the average output voltage. |
| 控制输出电压的方法之一是以恒定频率（因此，恒定的开关时间周期ts＝ton+toff）进行切换，并调整开关的接通持续时间以控制平均输出电压。 |
| In transfer function models these equations are transformed and variables are eliminated between them to find the relation between selected input and output variables. |
| 在传递函数模型中，对这些方程式进行了转换，并消除了它们之间的变量，以找到所选输入变量和输出变量之间的关系。 |
论文摘要翻译
第一篇: Observations of offshore wind characteristics by Doppler-LiDAR for wind energy applications
| 原文 | 译文 |
|---|---|
| The interest of investigating offshore wind characteristics is receiving growing attention worldwide, which mainly attempts to boost the development of offshore wind energy and accelerate sustainable development. In particular, the understanding of offshore wind characteristics at the hub heights of wind turbines is of great significance in regard to the assessment of economic feasibility and structural design of wind turbines. Since traditional meteorological masts have limitations in height due to economic and technical considerations, remote sensing techniques have increasingly been employed for offshore wind observations. | 海上风电特性的研究在世界范围内受到越来越多的关注，其主要目的是促进海上风能的开发和促进可持续发展。特别是了解风电机组枢纽高度处的海上风特性，对于评估风电机组的经济可行性和结构设计具有重要意义。由于传统的气象桅杆由于经济和技术上的考虑，高度受到限制，遥感技术越来越多地应用于海上风场观测。 |
| This paper presents a comprehensive assessment of offshore wind characteristics on the basis of measurements from a light detection and ranging (LiDAR) system at an offshore site in Hong Kong. The fidelity of the wind LiDAR measurements was firstly examined by comparing with those obtained from anemometers on a nearby meteorological mast. Statistical analysis of wind speed was performed by means of the Weibull distribution function, and the results were subsequently used to facilitate the determination of several characteristic parameters associated with wind energy applications. The vertical profiles of wind speed derived from the LiDAR system were compared with existing models. Characteristics of wind shear coefficient were examined within different height ranges. Furthermore, the offshore turbulence characteristics were investigated, including the turbulence intensity and gust factor. The outcomes of this study are expected to provide useful information for the development of offshore wind energy. | 本文基于香港近海光探测和测距（LIDAR）系统的测量结果，对海上风场特性进行了综合评价。通过与附近气象桅杆上风速计的测量结果进行比较，首次检验了测风激光雷达测量结果的保真度。利用Weibull分布函数对风速进行统计分析，结果随后用于确定与风能应用相关的几个特征参数。从激光雷达系统得到的风速垂直廓线与现有模型进行了比较。研究了不同高度范围内的风切变系数特征。此外，还研究了近海湍流特性，包括湍流强度和阵风因子。本文的研究成果有望为海上风能的开发提供有益的参考。 |
第二篇: A survey on consumers empowerment, communication technologies, and renewable generation penetration within Smart Grid
| 原文 | 译文 |
|---|---|
| The Smart Grid (SG) is a technological transformation from conventional electric grid, electro-mechanically controlled system, to smart, intelligent, and electronically controlled system called the “Smart Grid” (SG). There are about 20–30% losses present in the conventional electric grid due to substandard operations at generation, transmission and distribution side. The major players in the transformation are: (a) increased electricity cost, (b) aging infrastructure, © carbon footprint, (d) Green House Gas emissions, (e) climate change, and (f) less efficient electrical network. The promising features of the Smart Grid are: (a) intelligent de-centralized control, (b) resilience, © flexibility, (d) sustainability, (e) digitalization, (f) intelligence, (g) consumer empowerment, (h) green energy, and (i) smart infrastructure. | 智能电网（SG）是从传统的电力网、机电控制系统向智能化、智能化、电子控制系统（SG）的技术转型。由于发电、输电和配电侧运行不达标，传统电网约有20-30%的损耗。转型的主要参与者是：（a）电力成本增加，（b）基础设施老化，（c）碳足迹，（d）温室气体排放，（e）气候变化，以及（f）效率较低的电网。智能电网的有前途的特点是：（a）智能去集中式控制，（b）弹性，（c）灵活性，（d）可持续性，（e）数字化，（f）智能，（g）消费者授权，（H）绿色能源，和（I）智能基础设施。 |
| The fundamental issues and open challenges in the SG are lack of awareness, consumer acceptance, cyber terrorism, data collection management, energy metering, dynamic optimization and energy control. Considering above, in this paper, a comprehensive review exploring information of development, technologies, and techniques in the SG. The main goal is to investigate and reveal the key enabling technologies, to obtain better picture about the current status of SG development. The focus areas of this review study are Architectural Model focusing Consumer Empowerment (CE), Demand Response Program (DRP), and Demand Side Management (DSM). Our survey discusses in detail the Communication Technologies, such as Wireless Advance Metering Infrastructure (AMI), Phasor Measurement Unit (PMU), Supervisory Control and Data Acquisition (SCADA), and Machine to Machine Communication (M2M). The power systems such as Micro Grid, Nano Grid, Pico Grid, Inter Grid, Virtual Power Plants, and Distributed Generation are also elaborated in this review study. Renewable Energy Resources (RERs) Integration with the SG and Integration issues related to Distributed generation (DG) are presented in this survey. This survey also analyzes Architectural Model of the Smart Grid focusing consumer empowerment and prosumers interaction. The aim of this study is to provide deep understanding of technologies and their applications in the SG. | SG存在的根本问题和面临的挑战是缺乏认识、消费者接受度、网络恐怖主义、数据收集管理、能源计量、动态优化和能源控制。综上所述，本文对蒸汽发生器的发展、技术和技术进行了全面的综述。主要目的是研究和揭示关键的使能技术，更好地了解SG的发展现状。本综述研究的重点领域是关注消费者授权（CE）、需求响应计划（DRP）和需求侧管理（DSM）的架构模型。我们的调查详细讨论了通信技术，如无线预计量基础设施（AMI）、相量测量单元（PMU）、监控与数据采集（SCADA）和机对机通信（M2M）。对微电网、纳米电网、微微电网、互联电网、虚拟电厂、分布式发电等电力系统进行了综述。本文介绍了可再生能源（RERs）与SG的集成以及与分布式发电（DG）相关的集成问题。本次调查还分析了以消费者授权和消费者互动为重点的智能电网架构模型。本研究的目的是深入了解技术及其在蒸汽发生器中的应用。 |
第三篇: Mastering the game of Go with deep neural networks and tree search
| 原文 | 译文 |
|---|---|
| The game of Go has long been viewed as the most challenging of classic games for artificial intelligence due to its enormous search space and the difficulty of evaluating board positions and moves. We introduce a new approach to computer Go that uses value networks to evaluate board positions and policy networks to select moves. These deep neural networks are trained by a novel combination of supervised learning from human expert games, and reinforcement learning from games of self-play. Without any lookahead search, the neural networks play Go at the level of state-of-the-art Monte-Carlo tree search programs that simulate thousands of random games of self-play. We also introduce a new search algorithm that combines Monte-Carlo simulation with value and policy networks. Using this search algorithm, our program AlphaGo achieved a 99.8% winning rate against other Go programs, and defeated the European Go champion by 5 games to 0. This is the first time that a computer program has defeated a human professional player in the full-sized game of Go, a feat previously thought to be at least a decade away. | 围棋由于其巨大的搜索空间以及棋盘位置和动作的评估难度，一直被视为人工智能领域最具挑战性的经典游戏。我们提出了一种新的计算机围棋方法，它使用价值网络来评估棋盘位置，使用策略网络来选择移动。这些深层神经网络是由一种新的组合训练的监督学习从人类专家游戏，并加强学习从游戏的自我发挥。在没有任何前瞻性搜索的情况下，神经网络发挥了最先进的蒙特卡罗树搜索程序的水平，模拟数千个随机游戏的自我发挥。我们还介绍了一种新的搜索算法，将蒙特卡罗模拟与价值和策略网络相结合。使用这种搜索算法，我们的程序AlphaGo在与其他围棋程序的比赛中获得了99.8%的获胜率，并以5比0击败了欧洲围棋冠军。这是计算机程序第一次在全尺寸围棋游戏中击败人类专业玩家，这一壮举此前被认为至少还有十年的时间。 |
测控专业英语复习资料相关推荐
- 计算机系统项目管理师,信息系统项目管理师英语复习资料：计算机专业英语汇总[5]...
信息系统项目管理师英语复习资料:计算机专业英语汇总[5] 来源:信管网 2012年03月13日 [所有评论] S Scanner扫描器 Search查找 Secondary storage devic ...
- 英语听力采用计算机化考试,高考英语复习资料及听力机考特点与应对建议
高考英语听力机考特点与应对建议 北京市西城研修学院研修员 闫雪梅 2018年北京市高考英语听力将首次采用计算机化考试,与统考笔试分离.英语听力一年两次考试,取听力最高成绩与笔试成绩一同组成英语科目成绩 ...
- 从事仪表专业学c语言有用吗,测控专业就业方向有哪些 就业前景比你想象中的好...
测控专业就业方向有哪些?这个专业的就业前景好不好?这些问题都是小伙伴们比较关心的问题,下面随小编一起来了解一下吧. 主要就业方向 1.智能仪器仪表方向,我觉得这个方向主要是从事仪器仪表,电子产品的软件 ...
- 计算机与测控技术专业就业方向,测控专业就业方向及前景
测控专业作为热门专业之一,那么测控专业就业方向及前景怎么样呢.以下是由出国留学网编辑为大家整理的"测控专业就业方向及前景",仅供参考,欢迎大家阅读. 测控专业 1.测控专业简介 测 ...
- 计算机测控专业主要课程,大连海事大学测控技术与仪器专业要学哪些课程，好学吗？...
考生:请问大连海事大学测控技术与仪器专业要学哪些课程,好学吗? 大连海事大学测控技术与仪器专业要学的课程小编已经收集整理好啦,至于好不好学,这个真说不上来,因人而异吧. 专业中文名称测控技术与仪器 专 ...
- 测控计算机三级有用吗,测控专业与计算机三级
测控专业与计算机三级 答案:2 信息版本:手机版 解决时间 2019-10-02 13:40 已解决 2019-10-01 21:00 我是学测控技术与仪器专业的,计算机二级报考的是VB,现在我想报 ...
- 电大 学位英语 计算机 资料,电大学位英语复习资料
电大学位英语复习资料 学位英语考试不是全国统考,而是由各省区市独立组织报名及考试,考试时间也不尽相同.但学位英语的复习很重要.下面是小编为您整理的关于电大学位英语复习资料的相关资料,欢迎阅读! 形容词 ...
- 计算机测控专业主要课程,测控技术与仪器专业有哪些课程
测控技术与仪器专业有哪些课程2020-02-28 11:21:15文/张敏 测控技术与仪器专业培养具备精密仪器设计制造以及测量与控制方面基础知识与应用能力,能在国民经济各部门从事精密仪器与系统的设计制 ...
- 测控专业属于计算机吗,测控技术与仪器专业属于什么门类
在高考志愿填报的时很多考生和家长都不知道测控技术与仪器专业属于什么门类,很是影响考生的志愿填报专业选择,下面有途网小编根据考生的要求整理出测控技术与仪器专业属于工学类提供给大家,希望能够帮助考试顺利的 ...
- 计算机网络专业英语内容,计算机网络专业英语词汇资料.doc
网络专业英语词汇 AMIAlternate mark inversion信号交替反转编码ALU逻辑运算单元A/N字符/数字方式ACF/VTAMAdvanced communication facili ...
最新文章
- MySQL数据库字符集和整理
- VMware vSphere 6.5 配置文档
- mac电脑 显示隐藏文件 取消显示隐藏文件
- iview构建基本html页面,使用vue-cli创造基于vue.js的iview工程
- python 使用全局变量_如何在Python中的不同模块中使用全局变量
- NickLee.FortuneBase数据库sql server版本系统配置说明
- 20171207L09-04老男孩Linux运维实战培训-Lamp系列-Apache服务生产实战应用
- Java：控制台输入车辆信息，将信息保存至数据库中
- ABB 机器人 IRBP系列转台的一段代码注释
- [react] 如何用React实现滚动动画？
- 高温津贴：关键是消除劳动者“权利贫困”
- 学习oracle的感悟,随笔：最近关于Oracle学习思考的一些感悟
- 在Linux上安装MySql
- 浅谈linux线程模型和线程切换
- [POI2010]Divine Divisor
- VS2017优质插件总结
- KASLR-内核地址空间布局随机化
- [CF1129E]Legendary Tree
- 无损播放器Linux系统,Ubuntu Linux下支持无损CUE的音乐播放器——Qmmp
- MATLAB-随机森林实现数据回归分析预测