文章目录

  • 前言
  • 一、硬件细节
  • 二、原始固件LOG

前言

之前就有买过EBAZ4205控制板当开发板使，但是那块板子怎么说都是个四层板的丐板，板子还被抄了，立创0元打个板也一样能用。上面的内存还是杂牌的128M 16bit位宽内存，就连SD卡槽都没焊上去。改个启动方式还要挪0402的电阻，就连网口还是100M的而且占用的是PL端的IO，属实是不容易。虽然买的是块淘汰的板子，但是我还是有点最求，起码希望它不要那么丐。

于是在咸鱼上看到了T9+这块控制板，直接解决了我在EBAZ4205上面的大部分痛点，可以说是我对EBAZ4205改动的地方了。先上大图！

一、硬件细节

  1. 这次购买的板子总体比较旧，应该有长时间使用的迹象，板子上有的地方的灰比较大。同时可能长时间工作在潮湿环境中，板子上许多原件已经受潮，腐蚀的比较严重。比如下图的电感，及其周边电容的引脚，包括有些焊盘都是明显的锈蚀。

  2. 但是整板的质量比EBAZ4205要好得多，不管是布线还是字符的印刷。板子没有层数标注，推测应该是4层板，但是不排除6层的可能性，主要是因为部分布线不可见。电路板顶层还画了均流块（Copper Thieving）如下图，也称平衡铜、电镀块，指添加在多层PCB外层图形区、PCB装配辅条和制造面板辅条区域的铜平衡块。其作用是在电镀的过程中把电镀电流从铜箔密集区夺过来，让电流分布更平均，也就是避免成品铜厚的不均匀。 可以说是有做类似于阻抗控制一类的工作，还是不错的。
  3. 电源部分使用了5颗德仪的TLV62130，3-17V输入 3A 降压型DCDC，用于产生1V 1.5V 1.8V 2.5V 3.3V。没什么好说的，算是中规中矩的配置。内存方面倒是加了TPS51200，用于 DDR3、DDR3L 的 VTTREF 缓冲基准的 3A 灌电流/拉电流 DDR 终端稳压器，这玩意在EBAZ4205上就没焊！也是我抱怨的重点，而且这芯片没焊也就算了，在抄板的电路图上标了个14脚的芯片，人家明明是11脚的芯片，就是地焊盘长得奇怪了些，不至于这样吧，反正当时有点无语。
    PS:这货是用的DDR3L，怎么出1.5V电压（挠头）
  4. 网卡部分是使用了Broadcom 的 B50612E，由于实在是找不到资料，所以无法评价。但是比EBAZ4205的百兆要强太多了。
  5. 储存方面，用的是两颗镁光的DDR3L，一共512M的内存，可以说是相当够用了。

  6. NAND用的也是镁光，但是这商家拿东西给我贴上了，看不到型号，很生气。
  7. 其他接口方面，留了一个标准14Pin的JTAG，和一堆跳线用来更改启动方式，这个特别好

二、原始固件LOG

原始固件看起来也是基于linux的，不过固件开发版本确实太老了。有兴趣的可以自行观看，暂时不做讲解了

=~=~=~=~=~=~=~=~=~=~=~= MobaXterm log 2022.04.04 15:38:14 =~=~=~=~=~=~=~=~=~=~=~=Xilinx First Stage Boot Loader Release 2015.4Mar 29 2018-17:25:31
Devcfg driver initialized
Silicon Version 3.1
Boot mode is NAND
InitNand: Geometry = 0x8
Nand driver initialized NAND Init Done
Flash Base Address: 0xE1000000
Reboot status register: 0x60400000
Multiboot Register: 0x0000C000
Image Start Address: 0x00000000
Partition Header Offset:0x00000C80
Partition Count: 3
Partition Number: 1
Header Dump
Image Word Len: 0x0007F2E8
Data Word Len: 0x0007F2E8
Partition Word Len:0x0007F2E8
Load Addr: 0x00000000
Exec Addr: 0x00000000
Partition Start: 0x000075D0
Partition Attr: 0x00000020
Partition Checksum Offset: 0x00000000
Section Count: 0x00000001
Checksum: 0xFFE7AF06
Bitstream
In FsblHookBeforeBitstreamDload function
PCAP:StatusReg = 0x40000A30
PCAP:device ready
PCAP:Clear done
Level Shifter Value = 0xA
Devcfg Status register = 0x40000A30
PCAP:Fabric is Initialized done
PCAP register dump:
PCAP CTRL 0xF8007000: 0x4C00E07F
PCAP LOCK 0xF8007004: 0x0000001A
PCAP CONFIG 0xF8007008: 0x00000508
PCAP ISR 0xF800700C: 0x0802000B
PCAP IMR 0xF8007010: 0xFFFFFFFF
PCAP STATUS 0xF8007014: 0x50000F30
PCAP DMA SRC ADDR 0xF8007018: 0x00100001
PCAP DMA DEST ADDR 0xF800701C: 0xFFFFFFFF
PCAP DMA SRC LEN 0xF8007020: 0x0007F2E8
PCAP DMA DEST LEN 0xF8007024: 0x0007F2E8
PCAP ROM SHADOW CTRL 0xF8007028: 0xFFFFFFFF
PCAP MBOOT 0xF800702C: 0x0000C000
PCAP SW ID 0xF8007030: 0x00000000
PCAP UNLOCK 0xF8007034: 0x757BDF0D
PCAP MCTRL 0xF8007080: 0x30800100DMA Done ! FPGA Done ! In FsblHookAfterBitstreamDload function
Partition Number: 2
Header Dump
Image Word Len: 0x00015B20
Data Word Len: 0x00015B20
Partition Word Len:0x00015B20
Load Addr: 0x04000000
Exec Addr: 0x04000000
Partition Start: 0x000868C0
Partition Attr: 0x00000010
Partition Checksum Offset: 0x00000000
Section Count: 0x00000001
Checksum: 0xF7F3836E
Application
Handoff Address: 0x04000000
In FsblHookBeforeHandoff function
SUCCESSFUL_HANDOFF
FSBL Status = 0x1U-Boot 2014.01-gfb1d3e7-dirty (Mar 09 2018 - 19:36:04)I2C:   ready
Write: cnt = 0x08000000, addr = 0x20000000, *addr = 0xf7ffffff
Write: cnt = 0x04000000, addr = 0x10000000, *addr = 0xfbffffff
Write: cnt = 0x02000000, addr = 0x08000000, *addr = 0xfdffffff
Write: cnt = 0x01000000, addr = 0x04000000, *addr = 0xfeffffff
Write: cnt = 0x00800000, addr = 0x02000000, *addr = 0xff7fffff
Write: cnt = 0x00400000, addr = 0x01000000, *addr = 0xffbfffff
Write: cnt = 0x00200000, addr = 0x00800000, *addr = 0xffdfffff
Write: cnt = 0x00100000, addr = 0x00400000, *addr = 0xffefffff
Write: cnt = 0x00080000, addr = 0x00200000, *addr = 0xfff7ffff
Write: cnt = 0x00040000, addr = 0x00100000, *addr = 0xfffbffff
Write: cnt = 0x00020000, addr = 0x00080000, *addr = 0xfffdffff
Write: cnt = 0x00010000, addr = 0x00040000, *addr = 0xfffeffff
Write: cnt = 0x00008000, addr = 0x00020000, *addr = 0xffff7fff
Write: cnt = 0x00004000, addr = 0x00010000, *addr = 0xffffbfff
Write: cnt = 0x00002000, addr = 0x00008000, *addr = 0xffffdfff
Write: cnt = 0x00001000, addr = 0x00004000, *addr = 0xffffefff
Write: cnt = 0x00000800, addr = 0x00002000, *addr = 0xfffff7ff
Write: cnt = 0x00000400, addr = 0x00001000, *addr = 0xfffffbff
Write: cnt = 0x00000200, addr = 0x00000800, *addr = 0xfffffdff
Write: cnt = 0x00000100, addr = 0x00000400, *addr = 0xfffffeff
Write: cnt = 0x00000080, addr = 0x00000200, *addr = 0xffffff7f
Write: cnt = 0x00000040, addr = 0x00000100, *addr = 0xffffffbf
Write: cnt = 0x00000020, addr = 0x00000080, *addr = 0xffffffdf
Write: cnt = 0x00000010, addr = 0x00000040, *addr = 0xffffffef
Write: cnt = 0x00000008, addr = 0x00000020, *addr = 0xfffffff7
Write: cnt = 0x00000004, addr = 0x00000010, *addr = 0xfffffffb
Write: cnt = 0x00000002, addr = 0x00000008, *addr = 0xfffffffd
Write: cnt = 0x00000001, addr = 0x00000004, *addr = 0xfffffffe
Read: cnt = 0x00000001, addr = 0x00000004, val = 0xfffffffe
Read: cnt = 0x00000002, addr = 0x00000008, val = 0xfffffffd
Read: cnt = 0x00000004, addr = 0x00000010, val = 0xfffffffb
Read: cnt = 0x00000008, addr = 0x00000020, val = 0xfffffff7
Read: cnt = 0x00000010, addr = 0x00000040, val = 0xffffffef
Read: cnt = 0x00000020, addr = 0x00000080, val = 0xffffffdf
Read: cnt = 0x00000040, addr = 0x00000100, val = 0xffffffbf
Read: cnt = 0x00000080, addr = 0x00000200, val = 0xffffff7f
Read: cnt = 0x00000100, addr = 0x00000400, val = 0xfffffeff
Read: cnt = 0x00000200, addr = 0x00000800, val = 0xfffffdff
Read: cnt = 0x00000400, addr = 0x00001000, val = 0xfffffbff
Read: cnt = 0x00000800, addr = 0x00002000, val = 0xfffff7ff
Read: cnt = 0x00001000, addr = 0x00004000, val = 0xffffefff
Read: cnt = 0x00002000, addr = 0x00008000, val = 0xffffdfff
Read: cnt = 0x00004000, addr = 0x00010000, val = 0xffffbfff
Read: cnt = 0x00008000, addr = 0x00020000, val = 0xffff7fff
Read: cnt = 0x00010000, addr = 0x00040000, val = 0xfffeffff
Read: cnt = 0x00020000, addr = 0x00080000, val = 0xfffdffff
Read: cnt = 0x00040000, addr = 0x00100000, val = 0xfffbffff
Read: cnt = 0x00080000, addr = 0x00200000, val = 0xfff7ffff
Read: cnt = 0x00100000, addr = 0x00400000, val = 0xffefffff
Read: cnt = 0x00200000, addr = 0x00800000, val = 0xffdfffff
Read: cnt = 0x00400000, addr = 0x01000000, val = 0xffbfffff
Read: cnt = 0x00800000, addr = 0x02000000, val = 0xff7fffff
Read: cnt = 0x01000000, addr = 0x04000000, val = 0xfeffffff
Read: cnt = 0x02000000, addr = 0x08000000, val = 0xfdffffff
Read: cnt = 0x04000000, addr = 0x10000000, val = 0xfbffffff
Read: cnt = 0x08000000, addr = 0x20000000, val = 0xf7ffffff
---1 sys_sdram_size = 0x40000000
--- dram_init: sys_sdram_size = 1 GB---3 gd->ram_size = 0x3f000000
Memory: ECC disabled
DRAM:  1008 MiB
NAND:  256 MiB
MMC:   zynq_sdhci: 0
*** Warning - bad CRC, using default environmentIn:    serial
Out:   serial
Err:   serial
~~~1 gd->ram_size = 0x3f000000
~~~ board_late_init: ddr_size_type = 0--- gpio value = 0x000cc0ff
--- mount angstrom file system
bootargs: noinitrd mem=1008M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
--- upgrade marker upgrade_buf[0] = 0xff ---
--- upgrade marker upgrade_buf[1] = 0xff ---
--- upgrade marker upgrade_buf[2] = 0xff ---
--- upgrade marker upgrade_buf[3] = 0xff ---
--- upgrade marker upgrade_buf[4] = 0xff ---
--- upgrade marker upgrade_buf[5] = 0xff ---
--- upgrade marker upgrade_buf[6] = 0xff ---
--- upgrade marker upgrade_buf[7] = 0xff ---
--- upgrade marker upgrade_buf[8] = 0xff ---
--- upgrade marker upgrade_buf[9] = 0xff ---
--- upgrade marker upgrade_buf[10] = 0xff ---
--- upgrade marker upgrade_buf[11] = 0xff ---
--- upgrade marker upgrade_buf[12] = 0xff ---
--- upgrade marker upgrade_buf[13] = 0xff ---
--- upgrade marker upgrade_buf[14] = 0xff ---
--- upgrade marker upgrade_buf[15] = 0xff ---
bootargs: noinitrd mem=1008M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
Net:   Gem.e000b000
Hit any key to stop autoboot:  3  2  1  0
Copying Linux from NAND flash to RAM...NAND read: device 0 offset 0x1100000, size 0x8000008388608 bytes read: OKNAND read: device 0 offset 0x1020000, size 0x20000131072 bytes read: OK
## Booting kernel from Legacy Image at 02000000 ...Image Name:   Linux-3.14.0-xilinx-gb190cb0-dirImage Type:   ARM Linux Kernel Image (uncompressed)Data Size:    3779264 Bytes = 3.6 MiBLoad Address: 00008000Entry Point:  00008000Verifying Checksum ... OK
## Flattened Device Tree blob at 03000000Booting using the fdt blob at 0x3000000Loading Kernel Image ... OKLoading Device Tree to 1fffb000, end 1ffffdce ... OKStarting kernel ...Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-gb190cb0-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #57 SMP PREEMPT Fri Dec 9 14:49:22 CST 2016
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 27800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 256528
[    0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 884148K/1032192K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 148044K reserved, 253952K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to f0004000
[    0.000000] zynq_clock_init: clkc starts at f0004100
[    0.000000] Zynq clock init
[    0.000014] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000294] ps7-ttc #0 at f0006000, irq=43
[    0.000597] Console: colour dummy device 80x30
[    0.000632] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040202] pid_max: default: 32768 minimum: 301
[    0.040418] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.040439] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.042583] CPU: Testing write buffer coherency: ok
[    0.042905] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.042963] Setting up static identity map for 0x4c4af8 - 0x4c4b50
[    0.043179] L310 cache controller enabled
[    0.043197] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.120992] CPU1: Booted secondary processor
[    0.210223] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210351] Brought up 2 CPUs
[    0.210369] SMP: Total of 2 processors activated.
[    0.210378] CPU: All CPU(s) started in SVC mode.
[    0.211039] devtmpfs: initialized
[    0.213425] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214602] regulator-dummy: no parameters
[    0.221495] NET: Registered protocol family 16
[    0.223777] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.226021] cpuidle: using governor ladder
[    0.226034] cpuidle: using governor menu
[    0.233350] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.234841] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.234855] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.234964] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[    0.256473] bio: create slab <bio-0> at 0
[    0.257833] vgaarb: loaded
[    0.258531] SCSI subsystem initialized
[    0.259410] usbcore: registered new interface driver usbfs
[    0.259585] usbcore: registered new interface driver hub
[    0.259806] usbcore: registered new device driver usb
[    0.260638] media: Linux media interface: v0.10
[    0.260808] Linux video capture interface: v2.00
[    0.261355] pps_core: LinuxPPS API ver. 1 registered
[    0.261368] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.261502] PTP clock support registered
[    0.261861] EDAC MC: Ver: 3.0.0
[    0.262887] Advanced Linux Sound Architecture Driver Initialized.
[    0.265581] DMA-API: preallocated 4096 debug entries
[    0.265593] DMA-API: debugging enabled by kernel config
[    0.265659] Switched to clocksource arm_global_timer
[    0.285839] NET: Registered protocol family 2
[    0.286616] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.286711] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.286870] TCP: Hash tables configured (established 8192 bind 8192)
[    0.286927] TCP: reno registered
[    0.286946] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.286996] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.287249] NET: Registered protocol family 1
[    0.287614] RPC: Registered named UNIX socket transport module.
[    0.287626] RPC: Registered udp transport module.
[    0.287635] RPC: Registered tcp transport module.
[    0.287643] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.288080] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.290072] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.291416] bounce pool size: 64 pages
[    0.292286] jffs2: version 2.2. (NAND) ?2001-2006 Red Hat, Inc.
[    0.292483] msgmni has been set to 1486
[    0.293244] io scheduler noop registered
[    0.293257] io scheduler deadline registered
[    0.293297] io scheduler cfq registered (default)
[    0.305549] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.305569] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.426847] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    0.999033] console [ttyPS0] enabled
[    1.003285] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[    1.010903] [drm] Initialized drm 1.1.0 20060810
[    1.027705] brd: module loaded
[    1.037052] loop: module loaded
[    1.046548] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.052302] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.060212] libphy: XEMACPS mii bus: probed
[    1.064584] ------------- phy_id = 0x3625e62
[    1.069467] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.078067] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.084687] ehci-pci: EHCI PCI platform driver
[    1.091910] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.098743] usbcore: registered new interface driver usb-storage
[    1.105575] mousedev: PS/2 mouse device common for all mice
[    1.111727] i2c /dev entries driver
[    1.118679] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.124152] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.130045] Xilinx Zynq CpuIdle Driver started
[    1.134883] sdhci: Secure Digital Host Controller Interface driver
[    1.141004] sdhci: Copyright(c) Pierre Ossman
[    1.145316] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.152163] mmc0: no vqmmc regulator found
[    1.156206] mmc0: no vmmc regulator found
[    1.195691] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.204399] usbcore: registered new interface driver usbhid
[    1.209919] usbhid: USB HID core driver
[    1.214602] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.220898] nand: Micron MT29F2G08ABAEAWP
[    1.224863] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.230799] Bad block table found at page 131008, version 0x01
[    1.237023] Bad block table found at page 130944, version 0x01
[    1.243074] 3 ofpart partitions found on MTD device pl353-nand
[    1.248856] Creating 3 MTD partitions on "pl353-nand":
[    1.253945] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.261963] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.269274] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.278166] TCP: cubic registered
[    1.281397] NET: Registered protocol family 17
[    1.286101] Registering SWP/SWPB emulation handler
[    1.291944] regulator-dummy: disabling
[    1.296216] UBI: attaching mtd1 to ubi0
[    1.821947] UBI: scanning is finished
[    1.833554] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.840633] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.847393] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.854058] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.860936] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.866916] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.874023] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 2138264797
[    1.883066] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.892283] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.892288] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.896167] ALSA device list:
[    1.896170]   No soundcards found.
[    1.912588] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.941566] UBIFS: recovery needed
[    2.028878] UBIFS: recovery completed
[    2.032557] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.038502] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.047609] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.057497] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.062526] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 17F5A1A5-D13B-40BF-B801-9899D86E5DF6, small LPT model
[    2.073586] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.080549] devtmpfs: mounted
[    2.083652] Freeing unused kernel memory: 204K (c06d2000 - c0705000)INIT: version 2.88 booting
Starting Bootlog daemon: bootlogd.
Starting Monitor-ipsig daemon: monitor-ipsig.
[    2.923722] random: dd urandom read with 0 bits of entropy available
Starting initc
dropbear
cp: can't stat '/etc/minermonitor.conf.factory': No such file or directory
cp: can't stat '/etc/dataformatconfig': No such file or directory
[    3.335680]
[    3.335680] bcm54xx_config_init
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000link/ether 00:0a:35:00:01:22 brd ff:ff:ff:ff:ff:ff
ECC failed: 0
ECC corrected: 0
Number of bad blocks: 0
Number of bbt blocks: 0
Block size 131072, page size 2048, OOB size 64
Dumping data starting at 0x01080000 and ending at 0x01080020...
ECC failed: 0
ECC corrected: 0
Number of bad blocks: 0
Number of bbt blocks: 0
Block size 131072, page size 2048, OOB size 64
Dumping data starting at 0x01080000 and ending at 0x01080020...
ECC failed: 0
ECC corrected: 0
Number of bad blocks: 0
Number of bbt blocks: 0
Block size 131072, page size 2048, OOB size 64
Dumping data starting at 0x01080000 and ending at 0x01080001...
ECC failed: 0
ECC corrected: 0
Number of bad blocks: 0
Number of bbt blocks: 0
Block size 131072, page size 2048, OOB size 64
Dumping data starting at 0x01060000 and ending at 0x01060020...
ECC failed: 0
ECC corrected: 0
Number of bad blocks: 0
Number of bbt blocks: 0
Block size 131072, page size 2048, OOB size 64
Dumping data starting at 0x01060000 and ending at 0x01060020...
ECC failed: 0
ECC corrected: 0
Number of bad blocks: 0
Number of bbt blocks: 0
Block size 131072, page size 2048, OOB size 64
Dumping data starting at 0x01060000 and ending at 0x01060001...
06:41:07:f2:07:00
[    4.415711]
[    4.415711] bcm54xx_config_init
udhcpc (v1.21.1) started
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
No lease, forking to background
Error resolving pool.ntp.org: No address associated with hostname (-5)1 Jan 00:00:35 ntpdate[1458]: Can't find host pool.ntp.org: No address associated with hostname (-5)1 Jan 00:00:35 ntpdate[1458]: no servers can be used, exiting
Starting ntpd: done
Starting Avahi Daemon: Process 1473 died: No such process; trying to remove PID file. (/var/run/avahi-daemon//pid)
avahi-daemon.
Starting Lighttpd Web Server: lighttpd.
Starting bmminer daemon: ping: sendto: Network is unreachable
192.168.1.1 is reachable
No bitmain_axi.ko
[   40.543397] In axi fpga driver!
[   40.546485] request_mem_region OK!
[   40.549854] AXI fpga dev virtual address is 0xf01fe000
[   40.554962] *base_vir_addr = 0xc51e
memory_size = 1015424
fpga_mem_offset_addr=0x3F000000
[   40.569867] In fpga mem driver!
[   40.573068] request_mem_region OK!
[   40.576679] fpga mem virtual address is 0xf3000000
killall: bmminer: no process killed
killall: single-board-test: no process killed
bmminer.
Starting Monitor-recobtn daemon: monitor-recobtn.INIT: Entering runlevel: 5Stopping Bootlog daemon: workdataPathPrefix:/etc/config/minertest64/minertest64_Read Config.ini
Name:S9 HASH board
DataCount:912
PassCount1:912
PassCount2:912
PassCount3:912
Freq:600
Timeout:0
OpenCoreGap:50000
CheckTemp:0
freq_e:0
AsicNum:63
TestMode:0
CheckChain:1
CommandMode:0
ValidNonce1:57456
ValidNonce2:57456
ValidNonce3:57456
Pic:1d
IICPic:1d
dac = 1d
Voltage1:840d
Voltage2:840d
Voltage3:840d
OpenCoreNum1 = 4294967295d = 0xffffffff
OpenCoreNum2 = 4294967295d = 0xffffffff
OpenCoreNum3 = 4294967295d = 0xffffffff
OpenCoreNum4 = 262143d = 0x3ffff
GetTempFrom:1
TempSel:0
TempSensor1:62
TempSensor2:0
TempSensor3:0
TempSensor4:0
DefaultTempOffset:-70
StartTemp:0
year:2016
month:05
date:18
hour:10
minute:36
second:12parameter processed after Reading Config.ini
DataCount:912
PassCount1:912
PassCount2:912
PassCount3:912
Freq:600
Timeout:829
OpenCoreGap:50000
CheckTemp:0
TestMode:0
CommandMode:0
ValidNonce1:57456
ValidNonce2:57456
ValidNonce3:57456
Pic:1d
IICPic:1d
dac:1d
Voltage1:840d
Voltage2:840d
Voltage3:840d
OpenCoreNum1 = 4294967295d = 0xffffffff
OpenCoreNum2 = 4294967295d = 0xffffffff
OpenCoreNum3 = 4294967295d = 0xffffffff
OpenCoreNum4 = 262143d = 0x3ffff
GetTempFrom:1
TempSel:0
TempSensor1:62
TempSensor2:0
TempSensor3:0
TempSensor4:0
DefaultTempOffset:-70
StartTemp:0
year:2016
month:05
date:18
hour:10
minute:36
second:12bootlogd.
rm: can't remove '/config/temp_sensor': No such file or directory.---O---.                                           |       |                  .-.           o o        |   |   |-----.-----.-----.| |   .----..-----.-----.|       |     | __  |  ---'| '--.|  .-'|     |     ||   |   |  |  |     |---  ||  --'|  |  |  '  | | | |'---'---'--'--'--.  |-----''----''--'  '-----'-'-'-'-'  |'---'The Angstrom Distribution antMiner /dev/ttyPS0Angstrom v2013.12 - Kernel 3.14.0-xilinx-gb190cb0-dirtyantMiner login: single board test start
httpListenThread start ret=0
clement2 init_fpga
clement check_chain
clement2 init_fpga--- set command mode
clement2 set_dhash_acc_control vil
clement software_set_address--- set_baud
set_baud: system baudrate is: 0x0
clement2 set_nonce_fifo_interrupt
killall: bmminer: no process killed[1970-01-01 00:01:00.456] Miner compile time: Mon Jul 1 11:19:33 CST 2019 type: Antminer S9 rate: unknown                    [1970-01-01 00:01:00.457] Started bmminer 2.0.0                    [1970-01-01 00:01:00.457] Loaded configuration file /config/bmminer.conf                    [1970-01-01 00:01:08.481] Max fan speed: 0, Min fan speed: 0                    [1970-01-01 00:01:11.482] Max fan speed: 0, Min fan speed: 0
start listen on 6060 ...[1970-01-01 00:01:14.482] Max fan speed: 0, Min fan speed: 0                    [1970-01-01 00:01:17.482] Max fan speed: 0, Min fan speed: 0                    [1970-01-01 00:01:20.483] Max fan speed: 0, Min fan speed: 0

【ZYNQ】T9+控制板硬件概览与修复 （持续更新中）相关推荐

  1. 【STM32-V7】STM32H743XIH6开发板，丰富软件资源，强劲硬件配置，大量软件解决方案持续更新中（2020-07-22）

    [STM32-V7]STM32H743XIH6开发板,丰富软件资源,强劲硬件配置,大量软件解决方案持续更新中(2020-07-22) 参考文章: (1)[STM32-V7]STM32H743XIH6开 ...

  2. 【STM32-V6】STM32F429BIT6开发板开源, 丰富软件资源, 强劲硬件配置, 配套600多实例,21套手册持续更新中

    淘宝购买链接 从2016年1月份发布至今,软件资料更新过108次.当前标准库最新版本V2.8,HAL库最新版本V7.6 安富莱微信公共平台,欢迎大家关注(打造高质量公众号) HAL库版V7.6 STM ...

  3. linux运维常用命令一句话（持续更新中）

    整理收集一些Linux运维管理.系统管理的常用命令,太多了记不住,只能记录下来方便日后查看.也可以和大家分享.如果你有好的一句话命令也贴出来吧.本文持续更新中. 1.linux启动过程 开启电源 -- ...

  4. Go语言开发学习笔记（持续更新中）

    Go语言开发学习笔记(持续更新中) 仅供自我学习 更好的文档请选择下方 https://studygolang.com/pkgdoc https://www.topgoer.com/go%E5%9F% ...

  5. 嵌入式相关开源项目、库、资料------持续更新中

    学习初期最难找的就是找学习资料了,本贴精心汇总了一些嵌入式相关资源,包括但不限于编程语言.单片机.开源项目.物联网.操作系统.Linux.计算机等资源,并且在不断地更新中,致力于打造全网最全的嵌入式资 ...

  6. STM32 之十五 奇怪问题处理及驱动库 BUG 汇总（持续更新中）

      在使用 STM32 的 MCU 开发过程中,难免遇到各种各样的奇葩问题.或许是开发环境的问题,或许是 MCU 使用的问题,也或许是驱动库的 BUG 等等.这些问题可能不局限于某一种具体型号的 MC ...

  7. Linux常见命令作用（持续更新中，欢迎提议支持）

    Linux常见命令作用(持续更新中,欢迎提议支持) 1.ifconfig 查看ip地址 2.cd 切换工作目录(跳转路径) cd 路径 切换至工作目录"路径" 下同,指令后面都可附 ...

  8. JAVA面试大全(持续更新中...)

    本文旨在收集Java面试过程中出现的问题,力求全面,仅作学习交流,欢迎补充,持续更新中-,部分段落选取自网上,部分引用文章已标注,部分已记不清了,如侵权,联系本人 Java基础 1.面向对象的概述 面 ...

  9. 猴子都能懂得Git(入门篇汇总版)持续更新中~~~

    文章目录 前言 一.Git的基础 1.Git是什么? 2.管理历史记录的数据库 远程数据库和本地数据库 创建数据库 修改记录的提交 工作树和索引 2.安装Git 初期设定 新建数据库 提交文件 pus ...

最新文章

  1. 谷歌开源 TFGAN，让训练和评估 GAN 变得更加简单
  2. 掌握技术思想比解决问题本身更重要
  3. Java8-5-Function函数式接口进阶与默认方法详解
  4. 关于抠图的一些文章方法收集
  5. 实战Cisco路由器交换机各型号密码恢复
  6. java 邮件跟踪_如何跟踪邮件已读状态(Java)
  7. 数组转List的3种方法和使用对比！
  8. 诸如北京现代 只有四个轮子和一电瓶由中国制造(转自新华网)
  9. 微软最近宣布了一项政策更新，将限制在Office 365中使用Flash，Shockwave和Sil
  10. 技术经济与企业管理复习知识点总结
  11. C# WinForm程序 PDF文档分割代码实现
  12. 机器视觉：高动态范围图像
  13. wlh机器人_恐怖谷理论：人类对仿真机器人的天生恐惧
  14. 理解Sortino索提诺比率及Python实现
  15. 6-23 sdust-Java-可实现多种排序的Book类
  16. 超级 POM，POM的层级关系
  17. 离职前一定要删除这几个文件，不然你的微信聊天记录全被别人看了
  18. 还在用邀请码邀请注册吗?落后咯！！！我家APP自带邀请码的
  19. 转载的一篇存储图片等信息的还不错的文章
  20. 基于Java+SpringBoot+vue实现图书借阅和销售商城一体化系统

热门文章

  1. IPC-共享内存 (七猫的藏经阁 )
  2. windows电影杀毒linux程序,两部Linux有关的电影：《操作系统革命》《代码》
  3. 正本清源：为什么区块链是一次新的信息化革命
  4. IrfanView 看图软件下载及汉化
  5. react中findDomNode的作用
  6. OC10 -- block / 多态
  7. CH423要如何使用，便宜的国产IO扩展芯片
  8. (转)阿里宝宝的漫漫求职路
  9. 通常所说微型计算机的奔3,求江西省2011年计算机等级一级考试试题
  10. 软件架构师：走钢索的人