1、Burst Mode和Pulse Skipping Mode（PSM）的区别

Burst Mode ≠ Pulse Skipping Mode，论坛有人认为Burst Mode就是Pulse Skipping Mode，这是不对的。

以LTC3624为例：

Burst Mode operation provides the highest efficiency at light loads, while pulse-skipping mode provides the lowest voltage ripple.

To minimize VOUT ripple, pulse-skipping mode can be selected by grounding the MODE/SYNC pin. In the LTC3624/ LTC3624-2, pulse-skipping mode is implemented similarly to Burst Mode operation with the peak inductor current set to be at least 132mA. This results in lower ripple than in Burst Mode operation with the trade-off being slightly lower efficiency.

以LTC3412A为例：

Burst Mode Operation

Connecting the SYNC/MODE pin to a voltage in the range of 0V to 1V enables Burst Mode operation. In Burst Mode operation, the internal power MOSFETs operate intermittently at light loads. This increases efficiency by minimizing switching losses. During Burst Mode operation, the minimum peak inductor current is externally set by the voltage on the SYNC/MODE pin and the voltage on the ITH pin is monitored by the burst comparator to determine when sleep mode is enabled and disabled. When the average inductor current is greater than the load current, the voltage on the ITH pin drops. As the ITH voltage falls below 150mV, the burst comparator trips and enables sleep mode. During sleep mode, the top power MOSFET is held off and the ITH pin is disconnected from the output of the error amplifier. The majority of the internal circuitry is also turned off to reduce the quiescent current to 64µA while the load current is solely supplied by the output capacitor. When the output voltage drops, the ITH pin is reconnected to the output of the error amplifier and the top power MOSFET along with all the internal circuitry is switched back on. This process repeats at a rate that is dependent on the load demand.

Pulse-skipping operation

Pulse-skipping operation is implemented by connecting the SYNC/MODE pin to ground. This forces the burst clamp level to be at 0V. As the load current decreases, the peak inductor current will be determined by the voltage on the ITH pin until the ITH voltage drops below 400mV. At this point, the peak inductor current is determined by the minimum on-time of the current comparator. If the load demand is less than the average of the minimum on-time inductor current, switching cycles will be skipped to keep the output voltage in regulation.

1.1、Burst Mode

LTC7871不同模式对比：

FCM（Forced Continuous Conduction Mode）电流连续
DCM（Discontinuous Conduction Mode）电流不连续
Burst Mode 电流不连续

1.2、Pulse Skipping Mode（PSM）

2、Burst Mode作用

在轻载的时候，提高效率
在轻载货空载的时候，防止输出电压过冲

DCDC--Burst Mode和Pulse Skipping Mode相关推荐

PFM与PWM的技术总结
PFM与PWM的技术总结做电源设计的应该都知道PWM 和PFM 这两个概念: 开关电源的控制技术主要有三种:(1)脉冲宽度调制(PWM):(2)脉冲频率调制(PFM):(3)脉冲宽度频率调制(PWM ...
PFM和PWM技术总结
开关电源的控制技术主要有三种: (1)脉冲宽度调制(PWM):(2)脉冲频率调制(PFM):(3)脉冲宽度频率调制(PWM-PFM)． PWM:(pulse width modulation)脉冲宽度 ...
为您的DC/DC 转换器选择最佳开关频率
作者: 德州仪器Richard Nowakowski 及Brian King 提高开关频率的好处很明显,但也有些缺点,设计人员应了解其中的得失利弊,才能选择最合适的开关频率来加以应用.这篇实用文章将逐 ...
罗姆BD9P308MUF-C----- Nano Pulse Control™ 车载用 3.5V～40V输入 3.0A 单通道降压DC-DC转换器
产品特点: 纳米脉冲控制 AEC-Q100合格(注1) 最小ON脉冲50 ns (Max) 同步降压DC/DC变换器集成功率场效应管软启动功能电流模式控制 Reset功能轻载模式(LLM) 强 ...
关于DC-DC电源的总体概述
图(1) DC-DC变换器是将一种直流电转换成另一种固定的或者可调的直流电压,也称为直流---直流变换器. 通常把DC-DC电源分成两类:线性稳压电源和开关稳压电源.当然除了以上两种电源外,还有一种使 ...
ROHM | 面向高端ADAS开发出业界超稳定运行的DC-DC转换器IC“BD9S402MUF-C”
采用QuiCur™技术,显著减少日益复杂的车载应用的电源电路设计工时. 全球知名半导体制造商ROHM(总部位于日本京都)面向包括车载传感器和摄像头等在内的ADAS(高级驾驶辅助系统).信息娱乐系统等日 ...
HT7733 DC-DC升压芯片
HT7733 DC-DC升压芯片为盛群半导体*新推出的高效率升压型DC/DC转换器,利用CMOS制程以及PFM (Pulse Frequency Modulation) 技术,呈现低功耗及低噪音的** ...
内置MOS 同步DC-DC升压IC
内置MOS 同步DC-DC升压IC 型号工作模式工作电压范围输出电压输出电压形式输出电压精度输出电流限制效率静态电流工作频率封装直接替代型号 HM6382 ...
HT7727 DC-DC升压芯片
HT7727 DC-DC升压芯片为盛群半导体*新推出的高效率升压型DC/DC转换器,利用CMOS制程以及PFM (Pulse Frequency Modulation) 技术,呈现低功耗及低噪音的** ...

DCDC--Burst Mode和Pulse Skipping Mode

1、Burst Mode和Pulse Skipping Mode（PSM）的区别

1.1、Burst Mode

1.2、Pulse Skipping Mode（PSM）

2、Burst Mode作用

DCDC--Burst Mode和Pulse Skipping Mode相关推荐

最新文章

热门文章