3.3 示例程序

编程环境：Arduino 1.8.19

将参考例程（_1_servoWrite.ino）下载到主控板，调试时可以先只安装舵机输出头，或者安装输出头及L1连杆，运行观察舵机转动状况。

/*------------------------------------------------------------------------------------版权说明：Copyright 2023 Robottime(Beijing) Technology Co., Ltd. All Rights Reserved.Distributed under MIT license.See file LICENSE for detail or copy athttps://opensource.org/licenses/MITby 机器谱 2023-03-31 https://www.robotway.com/------------------------------*/#define SERVOLEFTNULL 500      //左侧舵机转动到0度的值#define SERVORIGHTNULL 500     //右侧舵机转动到0度的值#define SERVOFAKTORLEFT 603    //左侧舵机转动到0度右侧舵机转动到90度时的值#define SERVOFAKTORRIGHT 610   //左侧舵机转动到90度右侧舵机转动到180度时的值#define LIFT0 2000             //落笔写字时舵机转动的值#define LIFT1 1800             //一笔写完换笔时舵机转动的值#define LIFT2 1400             //初始及完成写字后抬笔时舵机的值#define SERVOPINLEFT 4         //定义一些舵机引脚#define SERVOPINRIGHT 7#define SERVOPINLIFT 11#define LIFTSPEED 1500         //定义抬笔落笔时舵机转动的速度#define L1 90                  //定义与舵机相连杆的长度 mm  #define L2 117.6               //定义与舵机相连杆的端点铰接处中心到笔中心的距离 mm#define L3 31.6                //定义中间杆顶端铰接处中心到笔的距离 mm#define X1 40.0                //定义左侧舵机中心轴到原点在X方向上的距离#define Y1 -42                 //定义左侧舵机中心轴到X轴的垂直距离#define X2 111.4               //定义右侧舵机中心轴到原点在X方向上的距离#define Y2 -42                 //定义右侧舵机中心轴到到X轴的垂直距离//坐标系建立第一象限，X轴方向为140mm,Y轴方向为120mm，选取坐标点时Y值建议大于70int coAry[10][10][2] = {         //汉字   王{{25,110},{0,0},{51,110},{1,1}},{{26,98},{0,0},{49,98},{1,1}},{{25,84},{0,0},{51,84},{1,1}},{{37,110},{0,0},{37,84},{1,1}},//汉字   云{{61,110},{0,0},{81,110},{1,1}},{{58,100},{0,0},{85,100},{1,1}},{{68,100},{0,0},{62,85},{86,85},{1,1}},{{80,96},{0,0},{91,82},{1,1}},//汉字   飞{{99,110},{0,0},{114,110},{114,98},{115,90},{115,86},{118,84},{121,82},{126,88},{1,1}},{{121,103},{0,0},{116,98},{122,94},{1,1}}};#include <Servo.h>int servoLift = LIFT2;Servo servo1;Servo servo2;Servo servo3;volatile double lastX = 57;   //笔初始坐标值volatile double lastY = 93;void setup() {Serial.begin(9600);        //开启串口通信/*servo1.attach(SERVOPINLEFT);servo2.attach(SERVOPINRIGHT);servo3.attach(SERVOPINLIFT);*/}void loop() {Serial.println("begin");if(1){  if(!servo1.attached()) servo1.attach(SERVOPINLEFT);if(!servo2.attached()) servo2.attach(SERVOPINRIGHT);if(!servo3.attached()) servo3.attach(SERVOPINLIFT);lift(2);//delay(1000);//汉字坐标处理for(int i=0;i<10;i++){for(int j=0;j<10;j++){int x = coAry[i][j][0];int y = coAry[i][j][1];//Serial.println(x);//Serial.println(y);if(x == 0 && y == 0){lift(0);continue;}else if(x == 1 && y == 1){lift(1);break;}drawTo(x,y);//delay(10);}}/*//摆臂测试坐标，左侧舵机转动到0度，右侧舵机转动到90度；左侧舵机转动到90度，右侧舵机转动到180度，依次循环drawTo(0,120.0);delay(1000);Serial.println("----------------------");drawTo(140.0, 120.0);delay(1000);///*/lift(2);servo1.detach();servo2.detach();servo3.detach();   Serial.println("end");}}//抬笔舵机转动函数，三个动作，落笔、换笔、起笔, 0 ,1, 2void lift(char lift){switch(lift){case 0:Serial.println("lift0");if(servoLift >= LIFT0){while(servoLift >= LIFT0){servoLift--;servo3.writeMicroseconds(servoLift);delayMicroseconds(LIFTSPEED);}}else{while(servoLift <= LIFT0){servoLift++;servo3.writeMicroseconds(servoLift);delayMicroseconds(LIFTSPEED);}}break;case 1:Serial.println("lift1");if(servoLift >= LIFT1){while(servoLift >= LIFT1){servoLift--;servo3.writeMicroseconds(servoLift);delayMicroseconds(LIFTSPEED);}}else{while(servoLift <= LIFT1){servoLift++;servo3.writeMicroseconds(servoLift);delayMicroseconds(LIFTSPEED);}}break;case 2:Serial.println("lift2");if(servoLift >= LIFT2){while(servoLift >= LIFT2){servoLift--;servo3.writeMicroseconds(servoLift);delayMicroseconds(LIFTSPEED);}}else{while(servoLift <= LIFT2){servoLift++;servo3.writeMicroseconds(servoLift);delayMicroseconds(LIFTSPEED);}}break;default:break;}}//笔移动函数，参数为点坐标值，计算两点坐标距离来控制笔移动void drawTo(double pX, double pY) {double dx, dy, c;int i;Serial.println(pX);Serial.println(pY);// dx dy of new pointdx = pX - lastX;dy = pY - lastY;//path lenght in mm, times 4 equals 4 steps per mmc = floor(1 * sqrt(dx * dx + dy * dy));if (c < 1) c = 1;for (i = 0; i <= c; i++) {// draw line point by pointset_XY(lastX + (i * dx / c), lastY + (i * dy / c));}lastX = pX;lastY = pY;}double return_angle(double a, double b, double c) {// cosine rule for angle between c and areturn acos((a * a + c * c - b * b) / (2 * a * c));}//用各种三角函数把位置坐标换算成舵机的角度，如何计算，请参考//http://www.thingiverse.com/thing:248009/void set_XY(double Tx, double Ty){delay(1);double dx, dy, c, a1, a2, Hx, Hy;// calculate triangle between pen, servoLeft and arm joint// cartesian dx/dydx = Tx - X1;dy = Ty - Y1;// polar lemgth (c) and angle (a1)c = sqrt(dx * dx + dy * dy); //a1 = atan2(dy, dx); //a2 = return_angle(L1, L2, c);//Serial.println(floor(((M_PI-a1 - a2) * SERVOFAKTORLEFT) + SERVOLEFTNULL));servo1.writeMicroseconds(floor(((M_PI-a1 - a2) * SERVOFAKTORLEFT) + SERVOLEFTNULL));// calculate joinr arm point for triangle of the right servo arma2 = return_angle(L2, L1, c);Hx = Tx + L3 * cos((a1 - a2 + 0.621) + M_PI); //36,5掳Hy = Ty + L3 * sin((a1 - a2 + 0.621) + M_PI);// calculate triangle between pen joint, servoRight and arm jointdx = Hx - X2;dy = Hy - Y2;c = sqrt(dx * dx + dy * dy);a1 = atan2(dy, dx);a2 = return_angle(L1, (L2 - L3), c);//Serial.println(floor(((M_PI - a1 + a2) * SERVOFAKTORRIGHT) + SERVORIGHTNULL));servo2.writeMicroseconds(floor(((M_PI - a1 + a2) * SERVOFAKTORRIGHT) + SERVORIGHTNULL));}