int ibv_query_qp(struct ibv_qp *qp, struct ibv_qp_attr *attr,enum ibv_qp_attr_mask attr_mask,struct ibv_qp_init_attr *init_attr);

struct ibv_qp_attr {enum ibv_qp_state qp_state;enum ibv_qp_state  cur_qp_state;enum ibv_mtu       path_mtu;enum ibv_mig_state path_mig_state;uint32_t     qkey;uint32_t       rq_psn;uint32_t     sq_psn;uint32_t     dest_qp_num;int         qp_access_flags;struct ibv_qp_cap   cap;struct ibv_ah_attr  ah_attr;struct ibv_ah_attr  alt_ah_attr;uint16_t        pkey_index;uint16_t     alt_pkey_index;uint8_t          en_sqd_async_notify;uint8_t         sq_draining;uint8_t         max_rd_atomic;uint8_t           max_dest_rd_atomic;uint8_t          min_rnr_timer;uint8_t           port_num;uint8_t            timeout;uint8_t         retry_cnt;uint8_t           rnr_retry;uint8_t           alt_port_num;uint8_t            alt_timeout;
};

Assume that this is the current QP state. This is useful if it is known to the application that the QP state is different from the assumed state by the low-level driver. It can be one of the enumerated values as qp_state. Not relevant for ibv_query_qp()

假设这是当前的QP状态。如果应用程序知道QP状态与底层驱动程序假定的状态不同，这将很有用。它可以是qp_state枚举值之一。与ibv_query_qp（）不相关

路径MTU（path MTU）（最大传输单位），即可以在路径中传输的数据包的最大有效负载大小。它可以是下列枚举值之一：

• IBV_MTU_256 - 256 bytes
• IBV_MTU_512 - 512 bytes
• IBV_MTU_1024 - 1024 bytes
• IBV_MTU_2048 - 2048 bytes
• IBV_MTU_4096 - 4096 bytes

对于UC和RC QP，在需要时，RDMA设备将自动将消息分段为该大小的数据包。

The state of the QP's path migration state machine if supported by the device (IBV_DEVICE_AUTO_PATH_MIG is set in dev_cap.device_cap_flags). It can be one of the following enumerated values:

如果设备支持QP的路径迁移状态机的状态（IBV_DEVICE_AUTO_PATH_MIG在dev_cap.device_cap_flags中设置）。它可以是下列枚举值之一：

• IBV_MIG_MIGRATED - 迁移了路径迁移的状态机，即完成了迁移的初始状态The state machine of path migration is Migrated, i.e. initial state of migration was done
• IBV_MIG_REARM - The state machine of path migration is Rearm, i.e. attempt to try to coordinate the remote RC QP to move both local and remote QPs to Armed state
• IBV_MIG_ARMED - The state machine of path migration is Armed, i.e. both local and remote QPs are ready to perform a path migration

将检查传入消息的Q_Key并可能将其用作传出的Q_Key（如果已设置“发送请求”中q_key的MSB）。仅与UD QP相关

RC和UC模式的 QP收到的数据包的包序号（24bit的值）

发送包的包序号。（24bit的值）

RC and UC模式的远端QP的number。（24bit的值）

当发送就是发往这个number的QP，接收数据也只接收从这个number的QP发来的数据。

Allowed access flags of the remote operations for incoming packets of RC and UC QPs. It is either 0 or the bitwise OR of one or more of the following flags:

RC和UC QP传入数据包的远程操作的允许访问标志。它是0或以下一个或多个标志的按位或：

• IBV_ACCESS_REMOTE_WRITE - Allow incoming RDMA Writes on this QP
• IBV_ACCESS_REMOTE_READ - Allow incoming RDMA Reads on this QP
• IBV_ACCESS_REMOTE_ATOMIC - Allow incoming Atomic operations on this QP

QP中的Wore Requests数的属性，如下表所述

Address vector of the primary path which describes the path information to the remote QP as described in the table below

主路径的地址向量，描述到远程QP的路径的信息，具体描述见下表。

Address vector of the alternate path which describes the path information to the remote QP as described in the table below. Can be used only if supported by the device (IBV_DEVICE_AUTO_PATH_MIG is set in dev_cap.device_cap_flags)

替代路径的地址向量，描述了到远程QP的路径信息，如下表所述。仅在设备支持的情况下才能使用（在dev_cap.device_cap_flags中设置了IBV_DEVICE_AUTO_PATH_MIG）

Primary P_Key index. The value of the entry in the P_Key table that outgoing packets from this QPwill be sent with and incoming packets to this QP will be verified within the Primary path

主P_Key索引。 P_Key表中与该QP的出站数据包一起发送以及到该QP的入站数据包将被验证的条目的值 将在主路径中进行验证

Alternate P_Key index. The value of the entry in the P_Key table that outgoing packets from this QP will be sent with and incoming packets to this QP will be verified within the Alternate path

备用P_Key索引。将在备用路径中验证P_Key表中与该QP一起发送的出站数据包以及与该QP的传入数据包一起发送的条目的值

If non-zero, generate the affiliated asynchronous event IBV_EVENT_SQ_DRAINED when the QP state becomes SQD.drained, i.e. the Send Queue is drained. Not relevant for ibv_query_qp()

如果非零，则在QP状态变为SQD.drained（即发送队列被耗尽）时生成关联的异步事件IBV_EVENT_SQ_DRAINED。与ibv_query_qp（）不相关

如果已设置，则表明正在进行发送队列排空(draining )。仅当QP处于SQD状态时相关

The number of RDMA Reads & atomic operations outstanding at any time that can be handled by this QP as an initiator. Relevant only for RC QPs

QP作为启动程序,在任何时候可以处理的RDMA读取和原子操作的数量。仅与RC QP相关

Minimum RNR NAK Timer Field Value. When an incoming message to this QP should consume a Work Request from the Receive Queue, but not Work Request is outstanding on that Queue, the QP will send an RNR NAK packet to the initiator. It does not affect RNR NAKs sent for other reasons. The value can be one of the following numeric values since those values aren’t enumerated:

最小RNR NAK计时器字段值。当传入消息到达此QP，将消费接收队列中的一个WR (Work Request)。但该队列上未完成工作请求时，QP将向发起方发送RNR NAK数据包。它不会影响由于其他原因发送的RNR NAK。该值可以是以下数字值之一（这些值未被枚举）：

仅与RC QP相关。

• 0 - 655.36 milliseconds delay
• 1 - 0.01 milliseconds delay
• 2 - 0.02 milliseconds delay
• 3 - 0.03 milliseconds delay
• 4 - 0.04 milliseconds delay
• 5 - 0.06 milliseconds delay
• 6 - 2.56 milliseconds delay
• 7 - 3.84 milliseconds delay
• 8 - 5.12 milliseconds delay
• 9 - 7.68 milliseconds delay
• 10 - 10.24 milliseconds delay
• 11 - 15.36 milliseconds delay
• 12 - 0.08 milliseconds delay
• 13 - 0.12 milliseconds delay
• 14 - 0.16 milliseconds delay
• 15 - 0.24 milliseconds delay
• 16 - 0.32 milliseconds delay
• 17 - 0.48 milliseconds delay
• 18 - 0.64 milliseconds delay
• 19 - 0.96 milliseconds delay
• 20 - 1.28 milliseconds delay
• 21 - 1.92 milliseconds delay
• 22 - 20.48 milliseconds delay
• 23 - 30.72 milliseconds delay
• 24 - 40.96 milliseconds delay
• 25 - 61.44 milliseconds delay
• 26 - 81.92 milliseconds delay
• 27 - 122.88 milliseconds delay
• 28 - 163.84 milliseconds delay
• 29 - 245.76 milliseconds delay
• 30 - 327.68 milliseconds delay
• 31 - 491.52 milliseconds delay

• 0 - infinite
• 1 - 8.192 usec (0.000008 sec)
• 2 - 16.384 usec (0.000016 sec)
• 3 - 32.768 usec (0.000032 sec)
• 4 - 65.536 usec (0.000065 sec)
• 5 - 131.072 usec (0.000131 sec)
• 6 - 262.144 usec (0.000262 sec)
• 7 - 524.288 usec (0.000524 sec)
• 8 - 1048.576 usec (0.00104 sec)
• 9 - 2097.152 usec (0.00209 sec)
• 10 - 4194.304 usec (0.00419 sec)
• 11 - 8388.608 usec (0.00838 sec)
• 12 - 16777.22 usec (0.01677 sec)
• 13 - 33554.43 usec (0.0335 sec)
• 14 - 67108.86 usec (0.0671 sec)
• 15 - 134217.7 usec (0.134 sec)
• 16 - 268435.5 usec (0.268 sec)
• 17 - 536870.9 usec (0.536 sec)
• 18 - 1073742 usec (1.07 sec)
• 19 - 2147484 usec (2.14 sec)
• 20 - 4294967 usec (4.29 sec)
• 21 - 8589935 usec (8.58 sec)
• 22 - 17179869 usec (17.1 sec)
• 23 - 34359738 usec (34.3 sec)
• 24 - 68719477 usec (68.7 sec)
• 25 - 137000000 usec (137 sec)
• 26 - 275000000 usec (275 sec)
• 27 - 550000000 usec (550 sec)
• 28 - 1100000000 usec (1100 sec)
• 29 - 2200000000 usec (2200 sec)
• 30 - 4400000000 usec (4400 sec)
• 31 - 8800000000 usec (8800 sec)

Relevant only to RC QPs

struct ibv_qp_init_attr {void            *qp_context;struct ibv_cq           *send_cq;struct ibv_cq          *recv_cq;struct ibv_srq         *srq;struct ibv_qp_cap   cap;enum ibv_qp_type    qp_type;int         sq_sig_all;
};

struct ibv_qp_cap {uint32_t       max_send_wr;uint32_t        max_recv_wr;uint32_t        max_send_sge;uint32_t       max_recv_sge;uint32_t       max_inline_data;
};

struct ibv_ah_attr {struct ibv_global_route   grh;uint16_t        dlid;uint8_t            sl;uint8_t          src_path_bits;uint8_t           static_rate;uint8_t         is_global;uint8_t           port_num;
};

struct ibv_global_route {union ibv_gid        dgid;uint32_t       flow_label;uint8_t          sgid_index;uint8_t          hop_limit;uint8_t           traffic_class;
};

用于标识数据包目标端口的GID

要查询的QP属性的掩码

将被QP的队列（QP's）属性填充

struct ibv_qp *qp;
struct ibv_qp_attr attr;
struct ibv_qp_init_attr init_attr;if (ibv_query_qp(qp, &attr,IBV_QP_STATE, &init_attr)) {fprintf(stderr, "Failed to query QP state\n");return -1;
}