内容介绍

原文档由会员 bshhty 发布

本论文共27页，12000余字

摘要

采用电力电子变频装置实现电压频率协调控制，改变了同步电机历来的恒速运行不能调速的面貌，使它和异步电机一样成为调速电机大家庭的一员。本文针对同步电机中具有代表性的凸极机，在忽略了一部分对误差影响较小而使算法复杂度大大增加的因素(如谐波磁势等)，对其内部电流、电压、磁通、磁链及转矩的相互关系进行了一系列定量分析，建立了简化的基于abc三相变量上的数学模型，并将其进行派克变换，转换成易于计算机控制的d/q坐标下的模型。再使用MATLAB中用于仿真模拟系统的SIMULINK对系统的各个部分进行封装及连接，系统总体分为电源、abc/dq转换器、电机内部模拟、控制反馈四个主要部分，并为其设计了专用的模块，同时对其中的一系列参数进行了配置。系统启动仿真后，在经历了一开始的振荡后，各输出相对于输出时间的响应较稳定。

关键词：同步电机 d/q模型 MATLAB SIMULINK 仿真。

The Simulation Platform of Synchronous Machine by MATLAB

Abstract:

The utilization of transducer realizes the control of voltage’s frequency. It changes the situation that Synchronous Machine is always running with constant speed. Just like Asynchronous Machine, Synchronous machine can also be viewed as a member of the timing machine. This thesis intends to aim at the typical salient pole machine in Synchronous Machine. Some quantitative analysis are made on relations of salient pole machine among current, voltage, flux, flux linkage and torque, under the condition that some factors such as harmonic electric potential are ignored. These factors have less influence on error but greatly increase complexity of arithmetic. Thus, simplified mathematic model is established on the basis of a, b, c three phase variables. By the Park transformation, this model is transformed to d, q model which, is easy to be controlled by computer. Simulink is used to masking and linking all the parts of the system. The system can be divided into four main parts, namely power system, abc/dq transformation, simulation model of the machine and feedback control. Special blocks are designed for the four parts and a series of parameters in these parts are configured. The results of simulation show that each output has a satisfactory response when there is disturbance.

Key Words: Synchronous Machine Simulation d/q Model MATLAB SIMULINK

参考文献

1．S. Wiggins. Introduction to Applied Nonlinear Dynamical System and Chaos. Springer-Verlag， 1990。

2．D. W. Novotny and T. A. Lipo. Vector Control and Dynamics of AC Drives， Oxford Science Publication， 1996。

3．陈伯石. 电力拖动自动控制系统(第2版). 北京：机械工业出版社， 2000。

4．薛定宇 陈阳泉. 系统仿真技术与应用. 北京：清华大学出版社， 2002。

5．任兴权. 控制系统仿真与计算机辅助设计. 沈阳：东北大学出版社， 1986。

6．陈衍. 同步电机运行基本理论与计算机算法. 北京：水力电子出版社，1992。

7．李发海 王岩 电机与拖动基础(第2版). 北京：清华大学出版社，1994。

8．Mohand mokhtari and Michel Marie. Matlab与Simulink工程应用. 北京：电子工业出版社，2002。

9．李海涛 邓樱. Matlab6.1基础与应用技巧 北京：国防工业出版社，2002。