[原创]裴讯K3救砖TTL竟然进入openwrt终端无法进入CFE-强力救砖

救砖连串口的 ,我就不说了,网上大把教程

斐讯GND/RX/TX，对应TTL模块GND/RXD/TXD

网上大把的k3救砖教程,但是他们进入的压根不是那个CFE终端界面,我这是openwrt呀,
我的是openwrt的界面,压根就无法输入那个鬼东西,无法输入flash命令, 连nvm什么命令都只能show ,经过我反复的折腾,我观察到了一个日志

Could not load 192.168.2.3:vmlinuz: Timeout occured

另外 cmd 开启ping 192.168.2.1 -t然后重启路由器发现刚开始能ping通, ping通大概3次,我认为就对应了,这里,ping不通之后就会进入什么安全模式,这个模式自己也ping不同,跟别说ping其他的,
我的路由器和我的电脑都是连好的,于是我把我电脑ip 改成192.2.3
然后打开tftp软件,设置2.3

image.png

然后重启路由器,我发现竟然这里显示进度了,果然了,openwrt的系统会默认尝试加载一个固定ip地址的固件,而我呢,则把我的k3原厂固件改名为vmlinuz放到这个tftp服务器下面,就自然而然检测通了.

最后各种进度不同了

image.png

之后串口并没有断开,但是已经到了网页了

image.png

最后这个串口模式很好玩, 我打开路由器的网址这边发生了一些变化,或许他们的漏洞检测,就是利用这个东西查看日志结合的吧

image.png

补充
连接ttl线后,第二根灯是亮的,关于有时候连不上有时候乱码可能是某些短路,可先关机,连上串口115200 ,然后红灯亮了也就是第二个灯,第一个红灯稍微亮一点点, 绿灯是百分百亮的.
这里是没有按重置键,是直接开机的显示.

image.png

再次重启, 跳过提示,直接开机,能看日志.

WRDMW0 00000025
WRDMW0 00000024ADDR0000000000111111111122222222223333333333444444444455555555556666012345678901234567890123456789012345678901234567890123456789012300 +++++++++++++++++++++S+++++++++X++++++++++++++++++++++++++++++++Decompressing...doneCFE version 7.14.164.303 (r666427) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: Tue Aug 10 20:24:59 CST 2021 (rokis@rokis-virtual-machine)
Copyright (C) 2000-2008 Broadcom Corporation.Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
DDR Clock: 800 MHz
Info: DDR frequency set from clkfreq=1400,*800*
robo_eee_advertise_init: GPHY0: EEE advertisement is disabled
robo_eee_advertise_init: GPHY1: EEE advertisement is disabled
robo_eee_advertise_init: GPHY2: EEE advertisement is disabled
robo_eee_advertise_init: GPHY3: EEE advertisement is disabled
robo_eee_advertise_init: GPHY4: EEE advertisement is disabled
et2: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.164.303 (r666427)
CPU type 0x0: 1400MHz
Tot mem: 524288 KBytesCFE mem:    0x00F00000 - 0x017C8668 (9209448)
Data:       0x00F5081C - 0x00F50D60 (1348)
BSS:        0x00F50D70 - 0x00FC6668 (481528)
Heap:       0x00FC6668 - 0x017C6668 (8388608)
Stack:      0x017C6668 - 0x017C8668 (8192)
Text:       0x00F00000 - 0x00F46A68 (289384)Device eth0:  hwaddr 2C-B2-1A-5D-63-D8, ipaddr 192.168.50.1, mask 255.255.255.0gateway not set, nameserver not set
Null Rescue Flag.
boot the image...nflash1.trx
go load
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: TFTP Server.
..tftp retry wait 0
Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
Loading: ..... 4724640 bytes read
Entry at 0x00008000
Closing network.
Starting program at 0x00008000
console [ttyS0] enabled, bootconsole disabled
serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117) is a 16550
brd: module loaded
loop: module loaded
pflash: found no supported devices
bcmsflash: found no supported devices
Boot partition size = 524288(0x80000)
lookup_nflash_rootfs_offset: offset = 0x400000
nflash: squash filesystem with lzma found at block 46
Creating 5 MTD partitions on "nflash":
0x000000000000-0x000000080000 : "boot"
0x000000080000-0x000000180000 : "nvram"
0x000000180000-0x000000400000 : "phicomm"
0x000000400000-0x000004000000 : "linux"
0x0000005dc960-0x000004000000 : "rootfs"
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
=== PPTP init ===
Mirror/redirect action on
u32 classifierPerformance counters onActions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (8041 buckets, 32164 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
NET: Registered protocol family 15
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Registering the dns_resolver key type
Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Unknown NAND 128MiB 3,3V 8-bit)
Spare area=64 eccbytes 28, ecc bytes located at:9 10 11 12 13 14 15 25 26 27 28 29 30 31 41 42 43 44 45 46 47 57 58 59 60 61 62 63
Available 35 bytes at (off,len):
(1,8) (16,9) (32,9) (48,9) (0,0) (0,0) (0,0) (0,0)
Scanning device for bad blocks
Bad eraseblock 87 at 0x000000ae0000
Bad eraseblock 179 at 0x000001660000
Bad eraseblock 625 at 0x000004e20000
Options: NO_AUTOINCR,NO_READRDY,NO_SUBPAGE_WRITE,
Creating 1 MTD partitions on "brcmnand":
0x000004000000-0x000008000000 : "brcmnand"
VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
devtmpfs: mounted
Freeing init memory: 296K
init_main start1: set_action 0Hit ENTER for console...firmware version: 386.3_2
_ifconfig: name=lo flags=1043 IFUP addr=127.0.0.1 netmask=255.0.0.0
_ifconfig: name=lo:0 flags=1043 IFUP addr=127.0.1.1 netmask=255.0.0.0
route_manip: cmd=ADD name=lo addr=127.0.0.0 netmask=255.0.0.0 gateway=0.0.0.0 metric=0
[1 preinit:init_nvram +8] init_nvram for model(58)
reset phy_ed_thresh.mtd
**** k3.c[k3_init(153)] k3 init begin.
**** k3.c[update_cfe_k3(65)] Check CFE version...
ctf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
et_module_init: passivemode set to 0x0
et_module_init: txworkq set to 0x0
et_module_init: et_txq_thresh set to 0xce4
et_module_init: et_rxlazy_timeout set to 0x3e8
et_module_init: et_rxlazy_framecnt set to 0x20
et_module_init: et_rxlazy_dyn_thresh set to 0
et0: bhdr_sz 0 bhdr_roff 0
fwd0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.164.303 (r666427)
et1: bhdr_sz 0 bhdr_roff 0
fwd1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.164.303 (r666427)
robo_eee_advertise_init: GPHY0: EEE advertisement is disabled
robo_eee_advertise_init: GPHY1: EEE advertisement is disabled
robo_eee_advertise_init: GPHY2: EEE advertisement is disabled
robo_eee_advertise_init: GPHY3: EEE advertisement is disabled
robo_eee_advertise_init: GPHY4: EEE advertisement is disabled
agg_attach: bhdr_enable 1
et2: bhdr_sz 4 bhdr_roff 12
et2: vlan1map 0xa7
et2: vlan2map 0x8
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.164.303 (r666427)
[config_lacp][144] RT-AC3100 could enable LACP
hotplug net INTERFACE=fwd1 ACTION=add SEQNUM=267
hotplug net INTERFACE=fwd0 ACTION=add SEQNUM=265
hotplug net INTERFACE=eth0 ACTION=add SEQNUM=271
hotplug net INTERFACE=agg ACTION=add SEQNUM=269
config_location(0x002e): [tcode_langcode] location is [XX]
config_location(0x0038): [tcode] location is [XX]config_location:p_location is modern, rev is 4
config_location(0x0053): [tcode] config location: [0:ccode]=[Q1], [0:regrev]=[947]
config_location(0x005d): [tcode] set_wl_country, 0, [Q1], [947]
config_location(0x0077): [tcode] config location 5G: [1:ccode]=[Q1], [1:regrev]=[947]
config_location(0x0082): [tcode] set_wl_country, 1, [Q1], [947]
set_wltxpower(0x025a): unit: 0, txpower: 100
set_wltxpower(0x025a): unit: 1, txpower: 100
dpsta_init: Jun 12 2019 19:06:52 msglevel 0x1
hotplug net INTERFACE=dpsta ACTION=add SEQNUM=275
dhd_chk_cnt: 1
load_wl(): starting...
load_wl(): insmod dhd instance_base=0 dhd_msg_level=0.
PCI_PROBE:  bus 1, slot 0,vendor 14E4, device 4365(good PCI location)
PCI: Enabling device 0002:01:00.0 (0140 -> 0142)
dhd_attach(): thread:dhd_watchdog_thread:7d started
Dongle Host Driver, version 1.363.2 (r665954)
Compiled in drivers/net/wireless/bcmdhd on May 18 2021 at 20:55:17
Register interface [eth1]  MAC: 00:90:4c:18:d2:34hotplug net INTERFACE=eth1 ACTION=add SEQNUM=278
load_wl(): insmod dhd24 instance_base=1 dhd_msg_level=0.
load_wl(): end.
1: check_action 0: 1(preinit)
*** ubifs: jffs2 (5, 67108864)
*** ubifs: attach (/dev/mtd5, 1260662)
*** ubifs: jffs2 0, 0, 63741952
<rc_service> [i:service] 290:notify_rc start_skipd/jffs/.asusrouter killdon: errno: 3 pid 258
_ifconfig: name=eth0 flags=1043 IFUP addr= netmask=
hotplug net INTERFACE=vlan1 ACTION=add SEQNUM=292
hotplug net INTERFACE=vlan2 ACTION=add SEQNUM=294
update_lan_state(lan_, 0, 0)
generate_wl_para(0x0fe0): unit 0 subunit -1
generate_wl_para(0x1390): set vhtmode -1
generate_wl_para(0x1486): bw: 1
generate_wl_para(0x1488): chanspec: 0
generate_wl_para(0x1489): bw_cap: 1
generate_wl_para(0x148f): obss_coex: 0
generate_wl_para(0x0fe0): unit 1 subunit -1
eth2: WLC_GET_VAR(cap): No such device
eth2: cmd=39 (errno 19): No such device
generate_wl_para(0x13b1): set vhtmode 1
generate_wl_para(0x1486): bw: 0
generate_wl_para(0x1488): chanspec: 0
generate_wl_para(0x1489): bw_cap: 3
generate_wl_para(0x148f): obss_coex: 0
_ifconfig: name=fwd0 flags=0000  addr= netmask=
_ifconfig: name=fwd0 flags=1343 IFUP addr= netmask=
_ifconfig: name=fwd1 flags=0000  addr= netmask=
_ifconfig: name=fwd1 flags=1343 IFUP addr= netmask=
vlan1: cmd=14 (errno 95): Operation not supported
_ifconfig: name=vlan1 flags=1243 IFUP addr= netmask=
_ifconfig: name=eth1 flags=1243 IFUP addr= netmask=
generate_wl_para(0x0fe0): unit 0 subunit -1
generate_wl_para(0x1390): set vhtmode -1
generate_wl_para(0x1486): bw: 1
generate_wl_para(0x1488): chanspec: 0
generate_wl_para(0x1489): bw_cap: 1
generate_wl_para(0x148f): obss_coex: 0
generate_wl_para(0x0fe0): unit 0 subunit 1
generate_wl_para(0x0fe0): unit 0 subunit 2
generate_wl_para(0x0fe0): unit 0 subunit 3
generate_wl_para(0x0fe0): unit 0 subunit 4
hotplug net INTERFACE=br0 ACTION=add SEQNUM=296
eth2: cmd=14 (errno 19): No such device
_ifconfig: name=eth2 flags=1243 IFUP addr= netmask=
eth2: No such device
start_lan: setting MAC address of bridge br0 as 2C:B2:1A:5D:63:D8
_ifconfig: name=br0 flags=1243 IFUP addr=192.168.50.1 netmask=255.255.255.0
_ifconfig: name=lo flags=1043 IFUP addr=127.0.0.1 netmask=255.0.0.0
_ifconfig: name=lo:0 flags=1043 IFUP addr=127.0.1.1 netmask=255.0.0.0
route_manip: cmd=ADD name=lo addr=127.0.0.0 netmask=255.0.0.0 gateway=0.0.0.0 metric=0
lo: File exists
update_lan_state(lan_, 2, 0)
nat_rule: stop_nat_rules 1.
stop_nat_rules: apply the redirect_rules state 0 ret 0
eth2: WLC_GET_VAR(chanspecs): No such device
failed to get valid chanspec list
: WLC_GET_VAR(chanspecs): No such device
failed to get valid chanspec list
: WLC_GET_VAR(chanspecs): No such device
failed to get valid chanspec list
: WLC_GET_VAR(chanspecs): No such device
failed to get valid chanspec listset exclchans base:
0:[0x100c,0x190a,0x100d,0x190b,0x100e,0x190c]
1:[0xd0a5]
2:[]
rc: ==> binding interface(vlan1,eth1,eth2,wds0.*,wds1.*,wds2.*) for lldpd
# wanduck: Got LAN(-1) information:
wanduck: delay 1 seconds before the first detect...
wanduck: delay 2 seconds before the first detect...
wanduck: delay 3 seconds before the first detect...
start_lan 2325
vlan1: cmd=14 (errno 95): Operation not supported
eth2: cmd=14 (errno 19): No such device
wanduck: delay 4 seconds before the first detect...
[1 preinit:start_dnsmasq +19] begin
[1 preinit:stop_dnsmasq +19] begin
[1 preinit:stop_stubby +19] begin
[1 preinit:stop_stubby +19] end
[1 preinit:stop_dnsmasq +19] end
[1 preinit:start_stubby +19] begin
[register_feature] blockfile registered
[register_feature] chknvram registered
[register_feature] misc registered
[are_all_sig_file_valid] Local version file is invalid!
[init] Remove all invalid files
wanduck: delay 5 seconds before the first detect...
[1 preinit:start_dnsmasq +20] end
amaslib_lease_main():: add, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
vendor class=MSFT 5.0
start_lan_port(0) 1
msgget ok
### onboarding model=RT-AC3100, reboot_time=120, connection_timeout=60, traffic_timeout=60
TZ watchdog
wanduck(0): NC send SYS_WAN_CABLE_UNPLUGGED_EVENT.# Enable direct rule
get_all_pc_list, enabled_str=, enabled=0.
disk_monitor: starting...
disk_monitor: day=5, week=6, time=13:5.
disk_monitor: decide if scan the target...
disk_monitor: 0: wait_second=36000...
disk_monitor: 1: wait_second=36000...
disk_monitor: wait_second=36000...
disk_monitor: Pause...[bwdpi check] starting...
rc: ==> binding interface(vlan1,eth1,eth2,wds0.*,wds1.*,wds2.*) for lldpd
rc: ==> binding interface match lldpd_bind_ifnames(vlan1,eth1,eth2,wds0.*,wds1.*,wds2.*)...
get_all_pc_list, enabled_str=, enabled=0.
Couldn't get the enabled rules of Parental-control correctly!
start_wan: start_wan_if(0)!
[1 preinit:start_wan_if +22] unit=0.
update_wan_state(wan0_, 0, 0)
convert_wan_nvram(wan0_)
_ifconfig: name=eth0 flags=0000  addr= netmask=
** wan_ifname: eth0 is NOT UP
_ifconfig: name=eth0 flags=1043 IFUP addr= netmask=
update_wan_state(wan0_, 1, 0)
start_wan_if(0x0767): ifup:eth0
_ifconfig: name=eth0 flags=1043 IFUP addr= netmask=
start_wan_if(0x077a): start auth:0
start_auth:: done
start_wan_if(0x077e): start udhcpc:eth0, 0
start_wan_if(): End.
udhcpc_wan:: deconfig
_ifconfig: name=eth0 flags=1043 IFUP addr=0.0.0.0 netmask=
wan_down(eth0)
wan_down(eth0): .
stop_auth:: done
route_manip: cmd=DEL name=eth0 addr=0.0.0.0 netmask=0.0.0.0 gateway=(null) metric=0
update_wan_state(wan0_, 3, 0)
update_wan_state(wan0_, 4, 3)
udhcpc:: deconfig done
amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
amaslib_lease_main():: done
vendor class=
eth2: WLC_GET_VAR(fabid): No such device
Enable USB power.
Start USB with the original procedure.
start_usb
no tune_bdflush
amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
amaslib_lease_main():: done
vendor class=MSFT 5.0
**** k3.c[start_k3screen(212)] k3screen: start
**** k3.c[start_k3screen(216)] k3screen: ok
**** k3.c[k3_init_done(197)] softcenter: init done
[1 preinit:init_main +25] recv signal 10 from pid [290:] (from user)
udhcpc_wan:: bound
error adding IE: -19
_ifconfig: name=eth0 flags=1043 IFUP addr=0.0.0.0 netmask=
_ifconfig: name=eth0 flags=1043 IFUP addr=192.168.1.124 netmask=255.255.255.0
wan_up(eth0)
update_wan_state(wan0_, 2, 0)
writting prerouting eth0 192.168.1.124 eth0 0.0.0.0 br0 192.168.50.1
get_all_pc_list, enabled_str=, enabled=0.
Couldn't get the enabled rules of Parental-control correctly!
nat_rule: start_nat_rules 1.
start_nat_rules: apply the nat_rules (/tmp/nat_rules_eth0_eth0) state 3 ret 0
[959 udhcpc:filter_setting +30] writing Internet Control
Couldn't get the enabled rules of Parental-control correctly!
Couldn't get the enabled rules of Parental-control correctly!
get_all_pc_list, enabled_str=, enabled=0.
Couldn't get the enabled rules of Parental-control correctly!
Couldn't get the enabled rules of Parental-control correctly!
[959 udhcpc:filter_setting +30] write porttrigger
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
start_auth:: done
add_multi_routes: running...
amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
amaslib_lease_main():: done
vendor class=NO default route!!!
hotplug net INTERFACE=zt6ovuxnwx ACTION=add SEQNUM=387
<rc_service> [i:udhcpc] 959:notify_rc stop_ntpd<rc_service> [i:udhcpc] 959:notify_rc start_ntpd[1 preinit:init_main +32] recv signal 10 from pid [959:/tmp/udhcpc] (from user)
959: wait for previous script(14/15): stop_ntpd 959 udhcpc.
cmd[0]=stop_ntpd
[1 preinit:handle_notifications +32] running: 1 ntpd
handle_notifications() end
[1 preinit:init_main +33] recv signal 10 from pid [959:/tmp/udhcpc] (from user)
cmd[0]=start_ntpd
[1 preinit:handle_notifications +33] running: 2 ntpd
stop igmpproxy
handle_notifications() end
RAST 33: ROAMAST Start...
RAST 33: ROAMING Start...
wan_up: wan_mac=D4:EE:07:00:00:00.
<rc_service> [i:udhcpc] 959:notify_rc stop_samba[1 preinit:init_main +34] recv signal 10 from pid [959:/tmp/udhcpc] (from user)
cmd[0]=stop_samba
[1 preinit:handle_notifications +34] running: 1 samba
<rc_service> [i:udhcpc] 959:notify_rc start_samba959: wait for previous script(29/30): stop_samba 959 udhcpc.
[rast_init_bssinfo]: WIF[eth1], idx[0]
rssi threshold: [0]
rssi hit count: [2]
idle period: [10]
idle rate: [100]gro disabled
handle_notifications() end
[WARNING] get instance eth2 error!!!
[rast_init_bssinfo]: WIF[eth2], idx[1]
rssi threshold: [0]
rssi hit count: [6]
idle period: [20]
idle rate: [10]
[rast_init_bssinfo]: TotalWI[2] RAST 35: [WARNING] eth2 get macmode error!!!
RAST 35: ipc accept socket...
wan_up(eth0): done.
udhcpc:: bound done
[1 preinit:init_main +35] recv signal 10 from pid [959:/tmp/udhcpc] (from user)
cmd[0]=start_samba
[1 preinit:handle_notifications +35] running: 2 samba
[1 preinit:start_dnsmasq +35] begin
[1 preinit:stop_dnsmasq +35] begin
killall_tk: waiting name=dnsmasq n=9
killall_tk: waiting name=dnsmasq n=8
killall_tk: waiting name=dnsmasq n=7
killall_tk: waiting name=dnsmasq n=6
killall_tk: waiting name=dnsmasq n=5
killall_tk: waiting name=dnsmasq n=4
killall_tk: waiting name=dnsmasq n=3
killall_tk: waiting name=dnsmasq n=2
killall_tk: waiting name=dnsmasq n=1
[1 preinit:stop_stubby +36] begin
[1 preinit:stop_stubby +36] end
[1 preinit:stop_dnsmasq +36] end
[1 preinit:start_stubby +36] begin
RAST 36: internal ipc accept socket...# Disable direct rule(D2C)......
nat_rule: start_nat_rules 3.
[1 preinit:start_dnsmasq +37] end
handle_notifications() end
<rc_service> [i:ntpd_synced] 1301:notify_rc restart_diskmon[1 preinit:init_main +37] recv signal 10 from pid [1301:/sbin/ntpd_synced] (from user)
cmd[0]=restart_diskmon
[1 preinit:handle_notifications +37] running: 3 diskmon
killall_tk: waiting name=disk_monitor n=9
killall_tk: waiting name=disk_monitor n=8
killall_tk: waiting name=disk_monitor n=7
killall_tk: waiting name=disk_monitor n=6
disk_monitor: Finish!
killall_tk: waiting name=disk_monitor n=5
handle_notifications() end
amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
amaslib_lease_main():: done
vendor class=
amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
disk_monitor: starting...
disk_monitor: day=4, week=0, time=1:13.
disk_monitor: decide if scan the target...
disk_monitor: 0: wait_second=2820...
disk_monitor: 1: wait_second=2820...
disk_monitor: wait_second=2820...
disk_monitor: Pause...amaslib_lease_main():: done
vendor class=
wanduck(0): NC send SYS_WAN_UNPUBLIC_IP_EVENT.
[Mastiff]exit.
Digital core power voltage set to 1.05V
Decompressing...done
Digital core power voltage set to 1.05VSHMOO VER 1.13PKID07DC06011801080000000000001A103F01000000S300001F7
00001510RDLYW0 00000004RDENW0 00000036RDQSW0 0000000000111111111122222222223333333333444444444455555555556666012345678901234567890123456789012345678901234567890123456789012300 ---------+++++++++++++++++++++++X+++++++++++++++++++++++--------01 -----------++++++++++++++++++++++++++X+++++++++++++++++++++++++-02 -----------+++++++++++++++++++++++++X++++++++++++++++++++++++---03 -------+-+++++++++++++++++++++++++X++++++++++++++++++++++++-----04 --++++++++++++++++++++++++X++++++++++++++++++++++++-------------05 ----------+++++++++++++++++++++++++++X++++++++++++++++++++++++--06 ---+++++++++++++++++++++++++X+++++++++++++++++++++++++----------07 ---------+++++++++++++++++++++++++X+++++++++++++++++++++++++----08 --++++++++++++++++++++++++++X+++++++++++++++++++++++++----------09 ------+++++++++++++++++++++++++X++++++++++++++++++++++++--------10 ------++++++++++++++++++++++++++X+++++++++++++++++++++++++------11 -------++++++++++++++++++++++++X++++++++++++++++++++++++--------12 --++++++++++++++++++++++++++X+++++++++++++++++++++++++----------13 ----++++++++++++++++++++++++X++++++++++++++++++++++++-----------14 ----+++++++++++++++++++++++++X++++++++++++++++++++++++----------15 ---+++++++++++++++++++++++++X+++++++++++++++++++++++++----------PW0 0000000000111111111122222222223333333333444444444455555555556666012345678901234567890123456789012345678901234567890123456789012300 -----+++++++++++++++++++++++++X+++++++++++++++++++++++++--------01 --------++++++++++++++++++++++++++++X++++++++++++++++++++++++++-02 ----++++++++++++++++++++++++++++X++++++++++++++++++++++++++++---03 -----+++++++++++++++++++++++++++X++++++++++++++++++++++++++-----04 +++++++++++++++++++++++++X+++++++++++++++++++++++++-------------05 -------++++++++++++++++++++++++++++X+++++++++++++++++++++++++++-06 +++++++++++++++++++++++++++X++++++++++++++++++++++++++----------07 ------++++++++++++++++++++++++++X++++++++++++++++++++++++++-----08 --+++++++++++++++++++++++++++X++++++++++++++++++++++++++--------09 -----++++++++++++++++++++++++++X++++++++++++++++++++++++++------10 -----+++++++++++++++++++++++++++X+++++++++++++++++++++++++++----11 ------+++++++++++++++++++++++++++X+++++++++++++++++++++++++++---12 --+++++++++++++++++++++++++++X+++++++++++++++++++++++++++-------13 --++++++++++++++++++++++++++X+++++++++++++++++++++++++----------14 -----++++++++++++++++++++++++++X+++++++++++++++++++++++++-------15 ---+++++++++++++++++++++++++++X++++++++++++++++++++++++++-------NW0 0000000000111111111122222222223333333333444444444455555555556666012345678901234567890123456789012345678901234567890123456789012300 ----------++++++++++++++++++++++++X+++++++++++++++++++++++------01 -----------++++++++++++++++++++++++++X+++++++++++++++++++++++++-02 ----------+++++++++++++++++++++++++X+++++++++++++++++++++++++---03 --------+++++++++++++++++++++++++X+++++++++++++++++++++++++-----04 --+++++++++++++++++++++++++X+++++++++++++++++++++++++-----------05 -----------++++++++++++++++++++++++++X+++++++++++++++++++++++++-06 ----++++++++++++++++++++++++++X+++++++++++++++++++++++++--------07 ---------+++++++++++++++++++++++++X+++++++++++++++++++++++++----08 -++++++++++++++++++++++++++X++++++++++++++++++++++++++----------09 ------+++++++++++++++++++++++++X++++++++++++++++++++++++--------10 ------++++++++++++++++++++++++++X+++++++++++++++++++++++++------11 -----+++++++++++++++++++++++++X++++++++++++++++++++++++---------12 -+++++++++++++++++++++++++++X++++++++++++++++++++++++++---------13 ---+++++++++++++++++++++++++X+++++++++++++++++++++++++----------14 ----++++++++++++++++++++++++X++++++++++++++++++++++++-----------15 --+++++++++++++++++++++++++X+++++++++++++++++++++++++-----------WRDQW0 0000000000111111111122222222223333333333444444444455555555556666012345678901234567890123456789012345678901234567890123456789012300 ++++++++++++++++++++++++X++++++++++++++++++++++++-------+++++++-01 +++++++++++++++++++++++++++X++++++++++++++++++++++++++-------++-02 ++++++++++++++++++++++++++X+++++++++++++++++++++++++------+++++-03 +++++++++++++++++++++++++X+++++++++++++++++++++++++-------+++++-04 +++++++++++++++++++++++X++++++++++++++++++++++-----------++++++-05 ++++++++++++++++++++++++++X+++++++++++++++++++++++++-------++++-06 +++++++++++++++++++++++X+++++++++++++++++++++++----------++++++-07 ++++++++++++++++++++++++++X++++++++++++++++++++++++++------++++-08 ++++++++++++++++++++++++X+++++++++++++++++++++++----------+++++-09 +++++++++++++++++++++++++X++++++++++++++++++++++++-------++++++-10 ++++++++++++++++++++++++++X++++++++++++++++++++++++++-----+++++-11 +++++++++++++++++++++++++X+++++++++++++++++++++++++-------+++++-12 +++++++++++++++++++++++X+++++++++++++++++++++++----------++++++-13 +++++++++++++++++++++++++X++++++++++++++++++++++++--------+++++-14 ++++++++++++++++++++++++X++++++++++++++++++++++++--------++++++-15 ++++++++++++++++++++++++X+++++++++++++++++++++++---------++++++-WRDMW0 00000025
WRDMW0 00000024ADDR0000000000111111111122222222223333333333444444444455555555556666012345678901234567890123456789012345678901234567890123456789012300 +++++++++++++++++++++S+++++++++X++++++++++++++++++++++++++++++++Decompressing...doneCFE version 7.14.164.303 (r666427) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: Tue Aug 10 20:24:59 CST 2021 (rokis@rokis-virtual-machine)
Copyright (C) 2000-2008 Broadcom Corporation.Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
DDR Clock: 800 MHz
Info: DDR frequency set from clkfreq=1400,*800*
robo_eee_advertise_init: GPHY0: EEE advertisement is disabled
robo_eee_advertise_init: GPHY1: EEE advertisement is disabled
robo_eee_advertise_init: GPHY2: EEE advertisement is disabled
robo_eee_advertise_init: GPHY3: EEE advertisement is disabled
robo_eee_advertise_init: GPHY4: EEE advertisement is disabled
et2: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.164.303 (r666427)
CPU type 0x0: 1400MHz
Tot mem: 524288 KBytesCFE mem:    0x00F00000 - 0x017C8668 (9209448)
Data:       0x00F5081C - 0x00F50D60 (1348)
BSS:        0x00F50D70 - 0x00FC6668 (481528)
Heap:       0x00FC6668 - 0x017C6668 (8388608)
Stack:      0x017C6668 - 0x017C8668 (8192)
Text:       0x00F00000 - 0x00F46A68 (289384)Device eth0:  hwaddr 2C-B2-1A-5D-63-D8, ipaddr 192.168.50.1, mask 255.255.255.0gateway not set, nameserver not set
Null Rescue Flag.
boot the image...nflash1.trx
go load
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: TFTP Server.
..tftp retry wait 0
Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
Loading: ..... 4724640 bytes read
Entry at 0x00008000
Closing network.
Starting program at 0x00008000
console [ttyS0] enabled, bootconsole disabled
serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117) is a 16550
brd: module loaded
loop: module loaded
pflash: found no supported devices
bcmsflash: found no supported devices
Boot partition size = 524288(0x80000)
lookup_nflash_rootfs_offset: offset = 0x400000
nflash: squash filesystem with lzma found at block 46
Creating 5 MTD partitions on "nflash":
0x000000000000-0x000000080000 : "boot"
0x000000080000-0x000000180000 : "nvram"
0x000000180000-0x000000400000 : "phicomm"
0x000000400000-0x000004000000 : "linux"
0x0000005dc960-0x000004000000 : "rootfs"
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
=== PPTP init ===
Mirror/redirect action on
u32 classifierPerformance counters onActions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (8041 buckets, 32164 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
NET: Registered protocol family 15
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Registering the dns_resolver key type
Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Unknown NAND 128MiB 3,3V 8-bit)
Spare area=64 eccbytes 28, ecc bytes located at:9 10 11 12 13 14 15 25 26 27 28 29 30 31 41 42 43 44 45 46 47 57 58 59 60 61 62 63
Available 35 bytes at (off,len):
(1,8) (16,9) (32,9) (48,9) (0,0) (0,0) (0,0) (0,0)
Scanning device for bad blocks
Bad eraseblock 87 at 0x000000ae0000
Bad eraseblock 179 at 0x000001660000
Bad eraseblock 625 at 0x000004e20000
Options: NO_AUTOINCR,NO_READRDY,NO_SUBPAGE_WRITE,
Creating 1 MTD partitions on "brcmnand":
0x000004000000-0x000008000000 : "brcmnand"
VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
devtmpfs: mounted
Freeing init memory: 296K
init_main start1: set_action 0Hit ENTER for console...firmware version: 386.3_2
_ifconfig: name=lo flags=1043 IFUP addr=127.0.0.1 netmask=255.0.0.0
_ifconfig: name=lo:0 flags=1043 IFUP addr=127.0.1.1 netmask=255.0.0.0
route_manip: cmd=ADD name=lo addr=127.0.0.0 netmask=255.0.0.0 gateway=0.0.0.0 metric=0
[1 preinit:init_nvram +8] init_nvram for model(58)
reset phy_ed_thresh.mtd
**** k3.c[k3_init(153)] k3 init begin.
**** k3.c[update_cfe_k3(65)] Check CFE version...
ctf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
et_module_init: passivemode set to 0x0
et_module_init: txworkq set to 0x0
et_module_init: et_txq_thresh set to 0xce4
et_module_init: et_rxlazy_timeout set to 0x3e8
et_module_init: et_rxlazy_framecnt set to 0x20
et_module_init: et_rxlazy_dyn_thresh set to 0
et0: bhdr_sz 0 bhdr_roff 0
fwd0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.164.303 (r666427)
et1: bhdr_sz 0 bhdr_roff 0
fwd1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.164.303 (r666427)
robo_eee_advertise_init: GPHY0: EEE advertisement is disabled
robo_eee_advertise_init: GPHY1: EEE advertisement is disabled
robo_eee_advertise_init: GPHY2: EEE advertisement is disabled
robo_eee_advertise_init: GPHY3: EEE advertisement is disabled
robo_eee_advertise_init: GPHY4: EEE advertisement is disabled
agg_attach: bhdr_enable 1
et2: bhdr_sz 4 bhdr_roff 12
et2: vlan1map 0xa7
et2: vlan2map 0x8
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.164.303 (r666427)
[config_lacp][144] RT-AC3100 could enable LACP
config_location(0x002e): [tcode_langcode] location is [XX]
config_location(0x0038): [tcode] location is [XX]config_location:p_location is modern, rev is 4
config_location(0x0053): [tcode] config location: [0:ccode]=[Q1], [0:regrev]=[947]
config_location(0x005d): [tcode] set_wl_country, 0, [Q1], [947]
config_location(0x0077): [tcode] config location 5G: [1:ccode]=[Q1], [1:regrev]=[947]
config_location(0x0082): [tcode] set_wl_country, 1, [Q1], [947]
set_wltxpower(0x025a): unit: 0, txpower: 100
set_wltxpower(0x025a): unit: 1, txpower: 100
dpsta_init: Jun 12 2019 19:06:52 msglevel 0x1
dhd_chk_cnt: 1
load_wl(): starting...
load_wl(): insmod dhd instance_base=0 dhd_msg_level=0.
hotplug net INTERFACE=fwd0 ACTION=add SEQNUM=265
hotplug net INTERFACE=eth0 ACTION=add SEQNUM=271
hotplug net INTERFACE=dpsta ACTION=add SEQNUM=275
hotplug net INTERFACE=agg ACTION=add SEQNUM=269
hotplug net INTERFACE=fwd1 ACTION=add SEQNUM=267
PCI_PROBE:  bus 1, slot 0,vendor 14E4, device 4365(good PCI location)
PCI: Enabling device 0002:01:00.0 (0140 -> 0142)
dhd_attach(): thread:dhd_watchdog_thread:7d started
Dongle Host Driver, version 1.363.2 (r665954)
Compiled in drivers/net/wireless/bcmdhd on May 18 2021 at 20:55:17
Register interface [eth1]  MAC: 00:90:4c:18:d2:34hotplug net INTERFACE=eth1 ACTION=add SEQNUM=278
load_wl(): insmod dhd24 instance_base=1 dhd_msg_level=0.
load_wl(): end.
1: check_action 0: 1(preinit)
*** ubifs: jffs2 (5, 67108864)
*** ubifs: attach (/dev/mtd5, 1260662)
*** ubifs: jffs2 0, 0, 63741952
<rc_service> [i:service] 290:notify_rc start_skipd/jffs/.asusrouter killdon: errno: 3 pid 258
_ifconfig: name=eth0 flags=1043 IFUP addr= netmask=
hotplug net INTERFACE=vlan1 ACTION=add SEQNUM=292
hotplug net INTERFACE=vlan2 ACTION=add SEQNUM=294
update_lan_state(lan_, 0, 0)
generate_wl_para(0x0fe0): unit 0 subunit -1
generate_wl_para(0x1390): set vhtmode -1
generate_wl_para(0x1486): bw: 1
generate_wl_para(0x1488): chanspec: 0
generate_wl_para(0x1489): bw_cap: 1
generate_wl_para(0x148f): obss_coex: 0
generate_wl_para(0x0fe0): unit 1 subunit -1
eth2: WLC_GET_VAR(cap): No such device
eth2: cmd=39 (errno 19): No such device
generate_wl_para(0x13b1): set vhtmode 1
generate_wl_para(0x1486): bw: 0
generate_wl_para(0x1488): chanspec: 0
generate_wl_para(0x1489): bw_cap: 3
generate_wl_para(0x148f): obss_coex: 0
_ifconfig: name=fwd0 flags=0000  addr= netmask=
_ifconfig: name=fwd0 flags=1343 IFUP addr= netmask=
_ifconfig: name=fwd1 flags=0000  addr= netmask=
_ifconfig: name=fwd1 flags=1343 IFUP addr= netmask=
vlan1: cmd=14 (errno 95): Operation not supported
_ifconfig: name=vlan1 flags=1243 IFUP addr= netmask=
_ifconfig: name=eth1 flags=1243 IFUP addr= netmask=
generate_wl_para(0x0fe0): unit 0 subunit -1
generate_wl_para(0x1390): set vhtmode -1
generate_wl_para(0x1486): bw: 1
generate_wl_para(0x1488): chanspec: 0
generate_wl_para(0x1489): bw_cap: 1
generate_wl_para(0x148f): obss_coex: 0
generate_wl_para(0x0fe0): unit 0 subunit 1
generate_wl_para(0x0fe0): unit 0 subunit 2
generate_wl_para(0x0fe0): unit 0 subunit 3
generate_wl_para(0x0fe0): unit 0 subunit 4
hotplug net INTERFACE=br0 ACTION=add SEQNUM=296
eth2: cmd=14 (errno 19): No such device
_ifconfig: name=eth2 flags=1243 IFUP addr= netmask=
eth2: No such device
start_lan: setting MAC address of bridge br0 as 2C:B2:1A:5D:63:D8
_ifconfig: name=br0 flags=1243 IFUP addr=192.168.50.1 netmask=255.255.255.0
_ifconfig: name=lo flags=1043 IFUP addr=127.0.0.1 netmask=255.0.0.0
_ifconfig: name=lo:0 flags=1043 IFUP addr=127.0.1.1 netmask=255.0.0.0
route_manip: cmd=ADD name=lo addr=127.0.0.0 netmask=255.0.0.0 gateway=0.0.0.0 metric=0
lo: File exists
update_lan_state(lan_, 2, 0)
nat_rule: stop_nat_rules 1.
stop_nat_rules: apply the redirect_rules state 0 ret 0
eth2: WLC_GET_VAR(chanspecs): No such device
failed to get valid chanspec list
: WLC_GET_VAR(chanspecs): No such device
failed to get valid chanspec list
: WLC_GET_VAR(chanspecs): No such device
failed to get valid chanspec list
: WLC_GET_VAR(chanspecs): No such device
failed to get valid chanspec listset exclchans base:
0:[0x100c,0x190a,0x100d,0x190b,0x100e,0x190c]
1:[0xd0a5]
2:[]
rc: ==> binding interface(vlan1,eth1,eth2,wds0.*,wds1.*,wds2.*) for lldpd
# wanduck: Got LAN(-1) information:
wanduck: delay 1 seconds before the first detect...
wanduck: delay 2 seconds before the first detect...
wanduck: delay 3 seconds before the first detect...
start_lan 2325
vlan1: cmd=14 (errno 95): Operation not supported
eth2: cmd=14 (errno 19): No such device
wanduck: delay 4 seconds before the first detect...
[register_feature] blockfile registered
[register_feature] chknvram registered
[register_feature] misc registered
[are_all_sig_file_valid] Local version file is invalid!
[init] Remove all invalid files
[1 preinit:start_dnsmasq +19] begin
[1 preinit:stop_dnsmasq +19] begin
[1 preinit:stop_stubby +19] begin
[1 preinit:stop_stubby +19] end
[1 preinit:stop_dnsmasq +19] end
[1 preinit:start_stubby +19] begin
wanduck: delay 5 seconds before the first detect...
[1 preinit:start_dnsmasq +20] end
start_lan_port(0) 1
amaslib_lease_main():: add, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
vendor class=MSFT 5.0
### onboarding model=RT-AC3100, reboot_time=120, connection_timeout=60, traffic_timeout=60
TZ watchdog
msgget ok
wanduck(0): NC send SYS_WAN_MODEM_OFFLINE_EVENT.# Enable direct rule
get_all_pc_list, enabled_str=, enabled=0.
disk_monitor: starting...
disk_monitor: day=5, week=6, time=13:5.
disk_monitor: decide if scan the target...
disk_monitor: 0: wait_second=36000...
disk_monitor: 1: wait_second=36000...
disk_monitor: wait_second=36000...
disk_monitor: Pause...get_all_pc_list, enabled_str=, enabled=0.
Couldn't get the enabled rules of Parental-control correctly!
[bwdpi check] starting...
rc: ==> binding interface(vlan1,eth1,eth2,wds0.*,wds1.*,wds2.*) for lldpd
rc: ==> binding interface match lldpd_bind_ifnames(vlan1,eth1,eth2,wds0.*,wds1.*,wds2.*)...
start_wan: start_wan_if(0)!
[1 preinit:start_wan_if +22] unit=0.
update_wan_state(wan0_, 0, 0)
convert_wan_nvram(wan0_)
_ifconfig: name=eth0 flags=0000  addr= netmask=
** wan_ifname: eth0 is NOT UP
_ifconfig: name=eth0 flags=1043 IFUP addr= netmask=
update_wan_state(wan0_, 1, 0)
start_wan_if(0x0767): ifup:eth0
_ifconfig: name=eth0 flags=1043 IFUP addr= netmask=
start_wan_if(0x077a): start auth:0
start_auth:: done
start_wan_if(0x077e): start udhcpc:eth0, 0
start_wan_if(): End.
udhcpc_wan:: deconfig
_ifconfig: name=eth0 flags=1043 IFUP addr=0.0.0.0 netmask=
wan_down(eth0)
wan_down(eth0): .
stop_auth:: done
route_manip: cmd=DEL name=eth0 addr=0.0.0.0 netmask=0.0.0.0 gateway=(null) metric=0
update_wan_state(wan0_, 3, 0)
update_wan_state(wan0_, 4, 3)
udhcpc:: deconfig done
amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
amaslib_lease_main():: done
vendor class=
udhcpc_wan:: bound
_ifconfig: name=eth0 flags=1043 IFUP addr=0.0.0.0 netmask=
_ifconfig: name=eth0 flags=1043 IFUP addr=192.168.1.124 netmask=255.255.255.0
wan_up(eth0)
update_wan_state(wan0_, 2, 0)
writting prerouting eth0 192.168.1.124 eth0 0.0.0.0 br0 192.168.50.1
get_all_pc_list, enabled_str=, enabled=0.
Couldn't get the enabled rules of Parental-control correctly!
nat_rule: start_nat_rules 1.
start_nat_rules: apply the nat_rules (/tmp/nat_rules_eth0_eth0) state 3 ret 0
[728 udhcpc:filter_setting +23] writing Internet Control
Couldn't get the enabled rules of Parental-control correctly!
Couldn't get the enabled rules of Parental-control correctly!
get_all_pc_list, enabled_str=, enabled=0.
Couldn't get the enabled rules of Parental-control correctly!
Couldn't get the enabled rules of Parental-control correctly!
[728 udhcpc:filter_setting +23] write porttrigger
eth2: WLC_GET_VAR(fabid): No such device
Enable USB power.
Start USB with the original procedure.
start_usb
no tune_bdflush
amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
amaslib_lease_main():: done
vendor class=MSFT 5.0
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
start_auth:: done
add_multi_routes: running...
amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
amaslib_lease_main():: done
vendor class=
<rc_service> [i:udhcpc] 728:notify_rc stop_ntpd<rc_service> [i:udhcpc] 728:notify_rc start_ntpd728: wait for previous script(14/15): stop_ntpd 728 udhcpc.
hotplug net INTERFACE=zt6ovuxnwx ACTION=add SEQNUM=376
error adding IE: -19
728: wait for previous script(13/15): stop_ntpd 728 udhcpc.
**** k3.c[start_k3screen(212)] k3screen: start
728: wait for previous script(12/15): stop_ntpd 728 udhcpc.
**** k3.c[start_k3screen(216)] k3screen: ok
**** k3.c[k3_init_done(197)] softcenter: init done# Disable direct rule(D2C)......
[1 preinit:init_main +26] recv signal 10 from pid [290:] (from user)
cmd[0]=stop_ntpd
[1 preinit:handle_notifications +27] running: 1 ntpd
handle_notifications() end
nat_rule: start_nat_rules 3.
[1 preinit:init_main +27] recv signal 10 from pid [728:/tmp/udhcpc] (from user)
cmd[0]=start_ntpd
[1 preinit:handle_notifications +27] running: 2 ntpd
stop igmpproxy
handle_notifications() end
wan_up: wan_mac=D4:EE:07:00:00:00.
<rc_service> [i:udhcpc] 728:notify_rc stop_samba[1 preinit:init_main +29] recv signal 10 from pid [728:/tmp/udhcpc] (from user)
cmd[0]=stop_samba
[1 preinit:handle_notifications +29] running: 1 samba
<rc_service> [i:udhcpc] 728:notify_rc start_samba728: wait for previous script(29/30): stop_samba 728 udhcpc.
amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GTgro disabled
handle_notifications() end
amaslib_lease_main():: done
vendor class=
wan_up(eth0): done.
udhcpc:: bound done
[1 preinit:init_main +30] recv signal 10 from pid [728:/tmp/udhcpc] (from user)
cmd[0]=start_samba
[1 preinit:handle_notifications +30] running: 2 samba
[1 preinit:start_dnsmasq +30] begin
[1 preinit:stop_dnsmasq +30] begin
killall_tk: waiting name=dnsmasq n=9
killall_tk: waiting name=dnsmasq n=8
killall_tk: waiting name=dnsmasq n=7
killall_tk: waiting name=dnsmasq n=6
killall_tk: waiting name=dnsmasq n=5
[1 preinit:stop_stubby +31] begin
[1 preinit:stop_stubby +31] end
[1 preinit:stop_dnsmasq +31] end
[1 preinit:start_stubby +31] begin
<rc_service> [i:ntpd_synced] 1171:notify_rc restart_diskmon1171: wait for previous script(14/15): start_samba 728 .
[1 preinit:start_dnsmasq +32] end
handle_notifications() end
wanduck(0): NC send SYS_WAN_UNPUBLIC_IP_EVENT.
[1 preinit:init_main +32] recv signal 10 from pid [1171:/sbin/ntpd_synced] (from user)
cmd[0]=restart_diskmon
[1 preinit:handle_notifications +32] running: 3 diskmon
killall_tk: waiting name=disk_monitor n=9
killall_tk: waiting name=disk_monitor n=8
killall_tk: waiting name=disk_monitor n=7
disk_monitor: Finish!
killall_tk: waiting name=disk_monitor n=6
killall_tk: waiting name=disk_monitor n=5
handle_notifications() end
amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
amaslib_lease_main():: done
vendor class=
disk_monitor: starting...
disk_monitor: day=4, week=0, time=1:19.
disk_monitor: decide if scan the target...
disk_monitor: 0: wait_second=2460...
disk_monitor: 1: wait_second=2460...
disk_monitor: wait_second=2460...
disk_monitor: Pause...amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
amaslib_lease_main():: done
vendor class=
RAST 34: ROAMAST Start...
RAST 34: ROAMING Start...
[rast_init_bssinfo]: WIF[eth1], idx[0]
rssi threshold: [0]
rssi hit count: [2]
idle period: [10]
idle rate: [100]
[WARNING] get instance eth2 error!!!
[rast_init_bssinfo]: WIF[eth2], idx[1]
rssi threshold: [0]
rssi hit count: [6]
idle period: [20]
idle rate: [10]
[rast_init_bssinfo]: TotalWI[2] RAST 35: [WARNING] eth2 get macmode error!!!
RAST 35: ipc accept socket...
RAST 36: internal ipc accept socket...WRDMW0 00000025
WRDMW0 00000024ADDR0000000000111111111122222222223333333333444444444455555555556666012345678901234567890123456789012345678901234567890123456789012300 +++++++++++++++++++++S+++++++++X++++++++++++++++++++++++++++++++Decompressing...doneCFE version 7.14.164.303 (r666427) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: Tue Aug 10 20:24:59 CST 2021 (rokis@rokis-virtual-machine)
Copyright (C) 2000-2008 Broadcom Corporation.Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
DDR Clock: 800 MHz
Info: DDR frequency set from clkfreq=1400,*800*
robo_eee_advertise_init: GPHY0: EEE advertisement is disabled
robo_eee_advertise_init: GPHY1: EEE advertisement is disabled
robo_eee_advertise_init: GPHY2: EEE advertisement is disabled
robo_eee_advertise_init: GPHY3: EEE advertisement is disabled
robo_eee_advertise_init: GPHY4: EEE advertisement is disabled
et2: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.164.303 (r666427)
CPU type 0x0: 1400MHz
Tot mem: 524288 KBytesCFE mem:    0x00F00000 - 0x017C8668 (9209448)
Data:       0x00F5081C - 0x00F50D60 (1348)
BSS:        0x00F50D70 - 0x00FC6668 (481528)
Heap:       0x00FC6668 - 0x017C6668 (8388608)
Stack:      0x017C6668 - 0x017C8668 (8192)
Text:       0x00F00000 - 0x00F46A68 (289384)Device eth0:  hwaddr 2C-B2-1A-5D-63-D8, ipaddr 192.168.50.1, mask 255.255.255.0gateway not set, nameserver not set
Null Rescue Flag.
boot the image...nflash1.trx
go load
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: TFTP Server.
..tftp retry wait 0
Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
Loading: ..... 4724640 bytes read
Entry at 0x00008000
Closing network.
Starting program at 0x00008000
console [ttyS0] enabled, bootconsole disabled
serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117) is a 16550
brd: module loaded
loop: module loaded
pflash: found no supported devices
bcmsflash: found no supported devices
Boot partition size = 524288(0x80000)
lookup_nflash_rootfs_offset: offset = 0x400000
nflash: squash filesystem with lzma found at block 46
Creating 5 MTD partitions on "nflash":
0x000000000000-0x000000080000 : "boot"
0x000000080000-0x000000180000 : "nvram"
0x000000180000-0x000000400000 : "phicomm"
0x000000400000-0x000004000000 : "linux"
0x0000005dc960-0x000004000000 : "rootfs"
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
=== PPTP init ===
Mirror/redirect action on
u32 classifierPerformance counters onActions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (8041 buckets, 32164 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
NET: Registered protocol family 15
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Registering the dns_resolver key type
Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Unknown NAND 128MiB 3,3V 8-bit)
Spare area=64 eccbytes 28, ecc bytes located at:9 10 11 12 13 14 15 25 26 27 28 29 30 31 41 42 43 44 45 46 47 57 58 59 60 61 62 63
Available 35 bytes at (off,len):
(1,8) (16,9) (32,9) (48,9) (0,0) (0,0) (0,0) (0,0)
Scanning device for bad blocks
Bad eraseblock 87 at 0x000000ae0000
Bad eraseblock 179 at 0x000001660000
Bad eraseblock 625 at 0x000004e20000
Options: NO_AUTOINCR,NO_READRDY,NO_SUBPAGE_WRITE,
Creating 1 MTD partitions on "brcmnand":
0x000004000000-0x000008000000 : "brcmnand"
VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
devtmpfs: mounted
Freeing init memory: 296K
init_main start1: set_action 0Hit ENTER for console...firmware version: 386.3_2
_ifconfig: name=lo flags=1043 IFUP addr=127.0.0.1 netmask=255.0.0.0
_ifconfig: name=lo:0 flags=1043 IFUP addr=127.0.1.1 netmask=255.0.0.0
route_manip: cmd=ADD name=lo addr=127.0.0.0 netmask=255.0.0.0 gateway=0.0.0.0 metric=0
[1 preinit:init_nvram +8] init_nvram for model(58)
reset phy_ed_thresh.mtd
**** k3.c[k3_init(153)] k3 init begin.
**** k3.c[update_cfe_k3(65)] Check CFE version...
ctf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
et_module_init: passivemode set to 0x0
et_module_init: txworkq set to 0x0
et_module_init: et_txq_thresh set to 0xce4
et_module_init: et_rxlazy_timeout set to 0x3e8
et_module_init: et_rxlazy_framecnt set to 0x20
et_module_init: et_rxlazy_dyn_thresh set to 0
et0: bhdr_sz 0 bhdr_roff 0
fwd0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.164.303 (r666427)
et1: bhdr_sz 0 bhdr_roff 0
fwd1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.164.303 (r666427)
robo_eee_advertise_init: GPHY0: EEE advertisement is disabled
robo_eee_advertise_init: GPHY1: EEE advertisement is disabled
robo_eee_advertise_init: GPHY2: EEE advertisement is disabled
robo_eee_advertise_init: GPHY3: EEE advertisement is disabled
robo_eee_advertise_init: GPHY4: EEE advertisement is disabled
agg_attach: bhdr_enable 1
et2: bhdr_sz 4 bhdr_roff 12
et2: vlan1map 0xa7
et2: vlan2map 0x8
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.164.303 (r666427)
[config_lacp][144] RT-AC3100 could enable LACP
hotplug net INTERFACE=fwd1 ACTION=add SEQNUM=267
hotplug net INTERFACE=fwd0 ACTION=add SEQNUM=265
hotplug net INTERFACE=eth0 ACTION=add SEQNUM=271
hotplug net INTERFACE=agg ACTION=add SEQNUM=269
config_location(0x002e): [tcode_langcode] location is [XX]
config_location(0x0038): [tcode] location is [XX]config_location:p_location is modern, rev is 4
config_location(0x0053): [tcode] config location: [0:ccode]=[Q1], [0:regrev]=[947]
config_location(0x005d): [tcode] set_wl_country, 0, [Q1], [947]
config_location(0x0077): [tcode] config location 5G: [1:ccode]=[Q1], [1:regrev]=[947]
config_location(0x0082): [tcode] set_wl_country, 1, [Q1], [947]
set_wltxpower(0x025a): unit: 0, txpower: 100
set_wltxpower(0x025a): unit: 1, txpower: 100
dpsta_init: Jun 12 2019 19:06:52 msglevel 0x1
hotplug net INTERFACE=dpsta ACTION=add SEQNUM=275
dhd_chk_cnt: 1
load_wl(): starting...
load_wl(): insmod dhd instance_base=0 dhd_msg_level=0.
PCI_PROBE:  bus 1, slot 0,vendor 14E4, device 4365(good PCI location)
PCI: Enabling device 0002:01:00.0 (0140 -> 0142)
dhd_attach(): thread:dhd_watchdog_thread:7d started
Dongle Host Driver, version 1.363.2 (r665954)
Compiled in drivers/net/wireless/bcmdhd on May 18 2021 at 20:55:17
Register interface [eth1]  MAC: 00:90:4c:18:d2:34hotplug net INTERFACE=eth1 ACTION=add SEQNUM=278
load_wl(): insmod dhd24 instance_base=1 dhd_msg_level=0.
load_wl(): end.
1: check_action 0: 1(preinit)
*** ubifs: jffs2 (5, 67108864)
*** ubifs: attach (/dev/mtd5, 1260662)
*** ubifs: jffs2 0, 0, 63741952
<rc_service> [i:service] 290:notify_rc start_skipd/jffs/.asusrouter killdon: errno: 3 pid 258
_ifconfig: name=eth0 flags=1043 IFUP addr= netmask=
hotplug net INTERFACE=vlan1 ACTION=add SEQNUM=292
hotplug net INTERFACE=vlan2 ACTION=add SEQNUM=294
update_lan_state(lan_, 0, 0)
generate_wl_para(0x0fe0): unit 0 subunit -1
generate_wl_para(0x1390): set vhtmode -1
generate_wl_para(0x1486): bw: 1
generate_wl_para(0x1488): chanspec: 0
generate_wl_para(0x1489): bw_cap: 1
generate_wl_para(0x148f): obss_coex: 0
generate_wl_para(0x0fe0): unit 1 subunit -1
eth2: WLC_GET_VAR(cap): No such device
eth2: cmd=39 (errno 19): No such device
generate_wl_para(0x13b1): set vhtmode 1
generate_wl_para(0x1486): bw: 0
generate_wl_para(0x1488): chanspec: 0
generate_wl_para(0x1489): bw_cap: 3
generate_wl_para(0x148f): obss_coex: 0
_ifconfig: name=fwd0 flags=0000  addr= netmask=
_ifconfig: name=fwd0 flags=1343 IFUP addr= netmask=
_ifconfig: name=fwd1 flags=0000  addr= netmask=
_ifconfig: name=fwd1 flags=1343 IFUP addr= netmask=
vlan1: cmd=14 (errno 95): Operation not supported
_ifconfig: name=vlan1 flags=1243 IFUP addr= netmask=
_ifconfig: name=eth1 flags=1243 IFUP addr= netmask=
generate_wl_para(0x0fe0): unit 0 subunit -1
generate_wl_para(0x1390): set vhtmode -1
generate_wl_para(0x1486): bw: 1
generate_wl_para(0x1488): chanspec: 0
generate_wl_para(0x1489): bw_cap: 1
generate_wl_para(0x148f): obss_coex: 0
generate_wl_para(0x0fe0): unit 0 subunit 1
generate_wl_para(0x0fe0): unit 0 subunit 2
generate_wl_para(0x0fe0): unit 0 subunit 3
generate_wl_para(0x0fe0): unit 0 subunit 4
hotplug net INTERFACE=br0 ACTION=add SEQNUM=296
eth2: cmd=14 (errno 19): No such device
_ifconfig: name=eth2 flags=1243 IFUP addr= netmask=
eth2: No such device
start_lan: setting MAC address of bridge br0 as 2C:B2:1A:5D:63:D8
_ifconfig: name=br0 flags=1243 IFUP addr=192.168.50.1 netmask=255.255.255.0
_ifconfig: name=lo flags=1043 IFUP addr=127.0.0.1 netmask=255.0.0.0
_ifconfig: name=lo:0 flags=1043 IFUP addr=127.0.1.1 netmask=255.0.0.0
route_manip: cmd=ADD name=lo addr=127.0.0.0 netmask=255.0.0.0 gateway=0.0.0.0 metric=0
lo: File exists
update_lan_state(lan_, 2, 0)
nat_rule: stop_nat_rules 1.
stop_nat_rules: apply the redirect_rules state 0 ret 0
eth2: WLC_GET_VAR(chanspecs): No such device
failed to get valid chanspec list
: WLC_GET_VAR(chanspecs): No such device
failed to get valid chanspec list
: WLC_GET_VAR(chanspecs): No such device
failed to get valid chanspec list
: WLC_GET_VAR(chanspecs): No such device
failed to get valid chanspec listset exclchans base:
0:[0x100c,0x190a,0x100d,0x190b,0x100e,0x190c]
1:[0xd0a5]
2:[]
rc: ==> binding interface(vlan1,eth1,eth2,wds0.*,wds1.*,wds2.*) for lldpd
# wanduck: Got LAN(-1) information:
wanduck: delay 1 seconds before the first detect...
wanduck: delay 2 seconds before the first detect...
wanduck: delay 3 seconds before the first detect...
start_lan 2325
vlan1: cmd=14 (errno 95): Operation not supported
eth2: cmd=14 (errno 19): No such device
wanduck: delay 4 seconds before the first detect...
[1 preinit:start_dnsmasq +19] begin
[1 preinit:stop_dnsmasq +19] begin
[1 preinit:stop_stubby +19] begin
[1 preinit:stop_stubby +19] end
[1 preinit:stop_dnsmasq +19] end
[1 preinit:start_stubby +19] begin
[register_feature] blockfile registered
[register_feature] chknvram registered
[register_feature] misc registered
[are_all_sig_file_valid] Local version file is invalid!
[init] Remove all invalid files
wanduck: delay 5 seconds before the first detect...
[1 preinit:start_dnsmasq +20] end
amaslib_lease_main():: add, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
vendor class=MSFT 5.0
start_lan_port(0) 1
msgget ok
### onboarding model=RT-AC3100, reboot_time=120, connection_timeout=60, traffic_timeout=60
TZ watchdog
wanduck(0): NC send SYS_WAN_CABLE_UNPLUGGED_EVENT.# Enable direct rule
get_all_pc_list, enabled_str=, enabled=0.
disk_monitor: starting...
disk_monitor: day=5, week=6, time=13:5.
disk_monitor: decide if scan the target...
disk_monitor: 0: wait_second=36000...
disk_monitor: 1: wait_second=36000...
disk_monitor: wait_second=36000...
disk_monitor: Pause...[bwdpi check] starting...
rc: ==> binding interface(vlan1,eth1,eth2,wds0.*,wds1.*,wds2.*) for lldpd
rc: ==> binding interface match lldpd_bind_ifnames(vlan1,eth1,eth2,wds0.*,wds1.*,wds2.*)...
get_all_pc_list, enabled_str=, enabled=0.
Couldn't get the enabled rules of Parental-control correctly!
start_wan: start_wan_if(0)!
[1 preinit:start_wan_if +22] unit=0.
update_wan_state(wan0_, 0, 0)
convert_wan_nvram(wan0_)
_ifconfig: name=eth0 flags=0000  addr= netmask=
** wan_ifname: eth0 is NOT UP
_ifconfig: name=eth0 flags=1043 IFUP addr= netmask=
update_wan_state(wan0_, 1, 0)
start_wan_if(0x0767): ifup:eth0
_ifconfig: name=eth0 flags=1043 IFUP addr= netmask=
start_wan_if(0x077a): start auth:0
start_auth:: done
start_wan_if(0x077e): start udhcpc:eth0, 0
start_wan_if(): End.
udhcpc_wan:: deconfig
_ifconfig: name=eth0 flags=1043 IFUP addr=0.0.0.0 netmask=
wan_down(eth0)
wan_down(eth0): .
stop_auth:: done
route_manip: cmd=DEL name=eth0 addr=0.0.0.0 netmask=0.0.0.0 gateway=(null) metric=0
update_wan_state(wan0_, 3, 0)
update_wan_state(wan0_, 4, 3)
udhcpc:: deconfig done
amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
amaslib_lease_main():: done
vendor class=
eth2: WLC_GET_VAR(fabid): No such device
Enable USB power.
Start USB with the original procedure.
start_usb
no tune_bdflush
amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
amaslib_lease_main():: done
vendor class=MSFT 5.0
**** k3.c[start_k3screen(212)] k3screen: start
**** k3.c[start_k3screen(216)] k3screen: ok
**** k3.c[k3_init_done(197)] softcenter: init done
[1 preinit:init_main +25] recv signal 10 from pid [290:] (from user)
udhcpc_wan:: bound
error adding IE: -19
_ifconfig: name=eth0 flags=1043 IFUP addr=0.0.0.0 netmask=
_ifconfig: name=eth0 flags=1043 IFUP addr=192.168.1.124 netmask=255.255.255.0
wan_up(eth0)
update_wan_state(wan0_, 2, 0)
writting prerouting eth0 192.168.1.124 eth0 0.0.0.0 br0 192.168.50.1
get_all_pc_list, enabled_str=, enabled=0.
Couldn't get the enabled rules of Parental-control correctly!
nat_rule: start_nat_rules 1.
start_nat_rules: apply the nat_rules (/tmp/nat_rules_eth0_eth0) state 3 ret 0
[959 udhcpc:filter_setting +30] writing Internet Control
Couldn't get the enabled rules of Parental-control correctly!
Couldn't get the enabled rules of Parental-control correctly!
get_all_pc_list, enabled_str=, enabled=0.
Couldn't get the enabled rules of Parental-control correctly!
Couldn't get the enabled rules of Parental-control correctly!
[959 udhcpc:filter_setting +30] write porttrigger
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
start_auth:: done
add_multi_routes: running...
amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
amaslib_lease_main():: done
vendor class=NO default route!!!
hotplug net INTERFACE=zt6ovuxnwx ACTION=add SEQNUM=387
<rc_service> [i:udhcpc] 959:notify_rc stop_ntpd<rc_service> [i:udhcpc] 959:notify_rc start_ntpd[1 preinit:init_main +32] recv signal 10 from pid [959:/tmp/udhcpc] (from user)
959: wait for previous script(14/15): stop_ntpd 959 udhcpc.
cmd[0]=stop_ntpd
[1 preinit:handle_notifications +32] running: 1 ntpd
handle_notifications() end
[1 preinit:init_main +33] recv signal 10 from pid [959:/tmp/udhcpc] (from user)
cmd[0]=start_ntpd
[1 preinit:handle_notifications +33] running: 2 ntpd
stop igmpproxy
handle_notifications() end
RAST 33: ROAMAST Start...
RAST 33: ROAMING Start...
wan_up: wan_mac=D4:EE:07:00:00:00.
<rc_service> [i:udhcpc] 959:notify_rc stop_samba[1 preinit:init_main +34] recv signal 10 from pid [959:/tmp/udhcpc] (from user)
cmd[0]=stop_samba
[1 preinit:handle_notifications +34] running: 1 samba
<rc_service> [i:udhcpc] 959:notify_rc start_samba959: wait for previous script(29/30): stop_samba 959 udhcpc.
[rast_init_bssinfo]: WIF[eth1], idx[0]
rssi threshold: [0]
rssi hit count: [2]
idle period: [10]
idle rate: [100]gro disabled
handle_notifications() end
[WARNING] get instance eth2 error!!!
[rast_init_bssinfo]: WIF[eth2], idx[1]
rssi threshold: [0]
rssi hit count: [6]
idle period: [20]
idle rate: [10]
[rast_init_bssinfo]: TotalWI[2] RAST 35: [WARNING] eth2 get macmode error!!!
RAST 35: ipc accept socket...
wan_up(eth0): done.
udhcpc:: bound done
[1 preinit:init_main +35] recv signal 10 from pid [959:/tmp/udhcpc] (from user)
cmd[0]=start_samba
[1 preinit:handle_notifications +35] running: 2 samba
[1 preinit:start_dnsmasq +35] begin
[1 preinit:stop_dnsmasq +35] begin
killall_tk: waiting name=dnsmasq n=9
killall_tk: waiting name=dnsmasq n=8
killall_tk: waiting name=dnsmasq n=7
killall_tk: waiting name=dnsmasq n=6
killall_tk: waiting name=dnsmasq n=5
killall_tk: waiting name=dnsmasq n=4
killall_tk: waiting name=dnsmasq n=3
killall_tk: waiting name=dnsmasq n=2
killall_tk: waiting name=dnsmasq n=1
[1 preinit:stop_stubby +36] begin
[1 preinit:stop_stubby +36] end
[1 preinit:stop_dnsmasq +36] end
[1 preinit:start_stubby +36] begin
RAST 36: internal ipc accept socket...# Disable direct rule(D2C)......
nat_rule: start_nat_rules 3.
[1 preinit:start_dnsmasq +37] end
handle_notifications() end
<rc_service> [i:ntpd_synced] 1301:notify_rc restart_diskmon[1 preinit:init_main +37] recv signal 10 from pid [1301:/sbin/ntpd_synced] (from user)
cmd[0]=restart_diskmon
[1 preinit:handle_notifications +37] running: 3 diskmon
killall_tk: waiting name=disk_monitor n=9
killall_tk: waiting name=disk_monitor n=8
killall_tk: waiting name=disk_monitor n=7
killall_tk: waiting name=disk_monitor n=6
disk_monitor: Finish!
killall_tk: waiting name=disk_monitor n=5
handle_notifications() end
amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
amaslib_lease_main():: done
vendor class=
amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
disk_monitor: starting...
disk_monitor: day=4, week=0, time=1:13.
disk_monitor: decide if scan the target...
disk_monitor: 0: wait_second=2820...
disk_monitor: 1: wait_second=2820...
disk_monitor: wait_second=2820...
disk_monitor: Pause...amaslib_lease_main():: done
vendor class=
wanduck(0): NC send SYS_WAN_UNPUBLIC_IP_EVENT.
[Mastiff]exit.
Digital core power voltage set to 1.05V
Decompressing...done
Digital core power voltage set to 1.05VSHMOO VER 1.13PKID07DC06011801080000000000001A103F01000000S300001F7
00001510RDLYW0 00000004RDENW0 00000036RDQSW0 0000000000111111111122222222223333333333444444444455555555556666012345678901234567890123456789012345678901234567890123456789012300 ---------+++++++++++++++++++++++X+++++++++++++++++++++++--------01 -----------++++++++++++++++++++++++++X+++++++++++++++++++++++++-02 -----------+++++++++++++++++++++++++X++++++++++++++++++++++++---03 -------+-+++++++++++++++++++++++++X++++++++++++++++++++++++-----04 --++++++++++++++++++++++++X++++++++++++++++++++++++-------------05 ----------+++++++++++++++++++++++++++X++++++++++++++++++++++++--06 ---+++++++++++++++++++++++++X+++++++++++++++++++++++++----------07 ---------+++++++++++++++++++++++++X+++++++++++++++++++++++++----08 --++++++++++++++++++++++++++X+++++++++++++++++++++++++----------09 ------+++++++++++++++++++++++++X++++++++++++++++++++++++--------10 ------++++++++++++++++++++++++++X+++++++++++++++++++++++++------11 -------++++++++++++++++++++++++X++++++++++++++++++++++++--------12 --++++++++++++++++++++++++++X+++++++++++++++++++++++++----------13 ----++++++++++++++++++++++++X++++++++++++++++++++++++-----------14 ----+++++++++++++++++++++++++X++++++++++++++++++++++++----------15 ---+++++++++++++++++++++++++X+++++++++++++++++++++++++----------PW0 0000000000111111111122222222223333333333444444444455555555556666012345678901234567890123456789012345678901234567890123456789012300 -----+++++++++++++++++++++++++X+++++++++++++++++++++++++--------01 --------++++++++++++++++++++++++++++X++++++++++++++++++++++++++-02 ----++++++++++++++++++++++++++++X++++++++++++++++++++++++++++---03 -----+++++++++++++++++++++++++++X++++++++++++++++++++++++++-----04 +++++++++++++++++++++++++X+++++++++++++++++++++++++-------------05 -------++++++++++++++++++++++++++++X+++++++++++++++++++++++++++-06 +++++++++++++++++++++++++++X++++++++++++++++++++++++++----------07 ------++++++++++++++++++++++++++X++++++++++++++++++++++++++-----08 --+++++++++++++++++++++++++++X++++++++++++++++++++++++++--------09 -----++++++++++++++++++++++++++X++++++++++++++++++++++++++------10 -----+++++++++++++++++++++++++++X+++++++++++++++++++++++++++----11 ------+++++++++++++++++++++++++++X+++++++++++++++++++++++++++---12 --+++++++++++++++++++++++++++X+++++++++++++++++++++++++++-------13 --++++++++++++++++++++++++++X+++++++++++++++++++++++++----------14 -----++++++++++++++++++++++++++X+++++++++++++++++++++++++-------15 ---+++++++++++++++++++++++++++X++++++++++++++++++++++++++-------NW0 0000000000111111111122222222223333333333444444444455555555556666012345678901234567890123456789012345678901234567890123456789012300 ----------++++++++++++++++++++++++X+++++++++++++++++++++++------01 -----------++++++++++++++++++++++++++X+++++++++++++++++++++++++-02 ----------+++++++++++++++++++++++++X+++++++++++++++++++++++++---03 --------+++++++++++++++++++++++++X+++++++++++++++++++++++++-----04 --+++++++++++++++++++++++++X+++++++++++++++++++++++++-----------05 -----------++++++++++++++++++++++++++X+++++++++++++++++++++++++-06 ----++++++++++++++++++++++++++X+++++++++++++++++++++++++--------07 ---------+++++++++++++++++++++++++X+++++++++++++++++++++++++----08 -++++++++++++++++++++++++++X++++++++++++++++++++++++++----------09 ------+++++++++++++++++++++++++X++++++++++++++++++++++++--------10 ------++++++++++++++++++++++++++X+++++++++++++++++++++++++------11 -----+++++++++++++++++++++++++X++++++++++++++++++++++++---------12 -+++++++++++++++++++++++++++X++++++++++++++++++++++++++---------13 ---+++++++++++++++++++++++++X+++++++++++++++++++++++++----------14 ----++++++++++++++++++++++++X++++++++++++++++++++++++-----------15 --+++++++++++++++++++++++++X+++++++++++++++++++++++++-----------WRDQW0 0000000000111111111122222222223333333333444444444455555555556666012345678901234567890123456789012345678901234567890123456789012300 ++++++++++++++++++++++++X++++++++++++++++++++++++-------+++++++-01 +++++++++++++++++++++++++++X++++++++++++++++++++++++++-------++-02 ++++++++++++++++++++++++++X+++++++++++++++++++++++++------+++++-03 +++++++++++++++++++++++++X+++++++++++++++++++++++++-------+++++-04 +++++++++++++++++++++++X++++++++++++++++++++++-----------++++++-05 ++++++++++++++++++++++++++X+++++++++++++++++++++++++-------++++-06 +++++++++++++++++++++++X+++++++++++++++++++++++----------++++++-07 ++++++++++++++++++++++++++X++++++++++++++++++++++++++------++++-08 ++++++++++++++++++++++++X+++++++++++++++++++++++----------+++++-09 +++++++++++++++++++++++++X++++++++++++++++++++++++-------++++++-10 ++++++++++++++++++++++++++X++++++++++++++++++++++++++-----+++++-11 +++++++++++++++++++++++++X+++++++++++++++++++++++++-------+++++-12 +++++++++++++++++++++++X+++++++++++++++++++++++----------++++++-13 +++++++++++++++++++++++++X++++++++++++++++++++++++--------+++++-14 ++++++++++++++++++++++++X++++++++++++++++++++++++--------++++++-15 ++++++++++++++++++++++++X+++++++++++++++++++++++---------++++++-WRDMW0 00000025
WRDMW0 00000024ADDR0000000000111111111122222222223333333333444444444455555555556666012345678901234567890123456789012345678901234567890123456789012300 +++++++++++++++++++++S+++++++++X++++++++++++++++++++++++++++++++Decompressing...doneCFE version 7.14.164.303 (r666427) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: Tue Aug 10 20:24:59 CST 2021 (rokis@rokis-virtual-machine)
Copyright (C) 2000-2008 Broadcom Corporation.Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
DDR Clock: 800 MHz
Info: DDR frequency set from clkfreq=1400,*800*
robo_eee_advertise_init: GPHY0: EEE advertisement is disabled
robo_eee_advertise_init: GPHY1: EEE advertisement is disabled
robo_eee_advertise_init: GPHY2: EEE advertisement is disabled
robo_eee_advertise_init: GPHY3: EEE advertisement is disabled
robo_eee_advertise_init: GPHY4: EEE advertisement is disabled
et2: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.164.303 (r666427)
CPU type 0x0: 1400MHz
Tot mem: 524288 KBytesCFE mem:    0x00F00000 - 0x017C8668 (9209448)
Data:       0x00F5081C - 0x00F50D60 (1348)
BSS:        0x00F50D70 - 0x00FC6668 (481528)
Heap:       0x00FC6668 - 0x017C6668 (8388608)
Stack:      0x017C6668 - 0x017C8668 (8192)
Text:       0x00F00000 - 0x00F46A68 (289384)Device eth0:  hwaddr 2C-B2-1A-5D-63-D8, ipaddr 192.168.50.1, mask 255.255.255.0gateway not set, nameserver not set
Null Rescue Flag.
boot the image...nflash1.trx
go load
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: TFTP Server.
..tftp retry wait 0
Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
Loading: ..... 4724640 bytes read
Entry at 0x00008000
Closing network.
Starting program at 0x00008000
console [ttyS0] enabled, bootconsole disabled
serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117) is a 16550
brd: module loaded
loop: module loaded
pflash: found no supported devices
bcmsflash: found no supported devices
Boot partition size = 524288(0x80000)
lookup_nflash_rootfs_offset: offset = 0x400000
nflash: squash filesystem with lzma found at block 46
Creating 5 MTD partitions on "nflash":
0x000000000000-0x000000080000 : "boot"
0x000000080000-0x000000180000 : "nvram"
0x000000180000-0x000000400000 : "phicomm"
0x000000400000-0x000004000000 : "linux"
0x0000005dc960-0x000004000000 : "rootfs"
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
=== PPTP init ===
Mirror/redirect action on
u32 classifierPerformance counters onActions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (8041 buckets, 32164 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
NET: Registered protocol family 15
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Registering the dns_resolver key type
Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Unknown NAND 128MiB 3,3V 8-bit)
Spare area=64 eccbytes 28, ecc bytes located at:9 10 11 12 13 14 15 25 26 27 28 29 30 31 41 42 43 44 45 46 47 57 58 59 60 61 62 63
Available 35 bytes at (off,len):
(1,8) (16,9) (32,9) (48,9) (0,0) (0,0) (0,0) (0,0)
Scanning device for bad blocks
Bad eraseblock 87 at 0x000000ae0000
Bad eraseblock 179 at 0x000001660000
Bad eraseblock 625 at 0x000004e20000
Options: NO_AUTOINCR,NO_READRDY,NO_SUBPAGE_WRITE,
Creating 1 MTD partitions on "brcmnand":
0x000004000000-0x000008000000 : "brcmnand"
VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
devtmpfs: mounted
Freeing init memory: 296K
init_main start1: set_action 0Hit ENTER for console...firmware version: 386.3_2
_ifconfig: name=lo flags=1043 IFUP addr=127.0.0.1 netmask=255.0.0.0
_ifconfig: name=lo:0 flags=1043 IFUP addr=127.0.1.1 netmask=255.0.0.0
route_manip: cmd=ADD name=lo addr=127.0.0.0 netmask=255.0.0.0 gateway=0.0.0.0 metric=0
[1 preinit:init_nvram +8] init_nvram for model(58)
reset phy_ed_thresh.mtd
**** k3.c[k3_init(153)] k3 init begin.
**** k3.c[update_cfe_k3(65)] Check CFE version...
ctf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
et_module_init: passivemode set to 0x0
et_module_init: txworkq set to 0x0
et_module_init: et_txq_thresh set to 0xce4
et_module_init: et_rxlazy_timeout set to 0x3e8
et_module_init: et_rxlazy_framecnt set to 0x20
et_module_init: et_rxlazy_dyn_thresh set to 0
et0: bhdr_sz 0 bhdr_roff 0
fwd0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.164.303 (r666427)
et1: bhdr_sz 0 bhdr_roff 0
fwd1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.164.303 (r666427)
robo_eee_advertise_init: GPHY0: EEE advertisement is disabled
robo_eee_advertise_init: GPHY1: EEE advertisement is disabled
robo_eee_advertise_init: GPHY2: EEE advertisement is disabled
robo_eee_advertise_init: GPHY3: EEE advertisement is disabled
robo_eee_advertise_init: GPHY4: EEE advertisement is disabled
agg_attach: bhdr_enable 1
et2: bhdr_sz 4 bhdr_roff 12
et2: vlan1map 0xa7
et2: vlan2map 0x8
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.164.303 (r666427)
[config_lacp][144] RT-AC3100 could enable LACP
config_location(0x002e): [tcode_langcode] location is [XX]
config_location(0x0038): [tcode] location is [XX]config_location:p_location is modern, rev is 4
config_location(0x0053): [tcode] config location: [0:ccode]=[Q1], [0:regrev]=[947]
config_location(0x005d): [tcode] set_wl_country, 0, [Q1], [947]
config_location(0x0077): [tcode] config location 5G: [1:ccode]=[Q1], [1:regrev]=[947]
config_location(0x0082): [tcode] set_wl_country, 1, [Q1], [947]
set_wltxpower(0x025a): unit: 0, txpower: 100
set_wltxpower(0x025a): unit: 1, txpower: 100
dpsta_init: Jun 12 2019 19:06:52 msglevel 0x1
dhd_chk_cnt: 1
load_wl(): starting...
load_wl(): insmod dhd instance_base=0 dhd_msg_level=0.
hotplug net INTERFACE=fwd0 ACTION=add SEQNUM=265
hotplug net INTERFACE=eth0 ACTION=add SEQNUM=271
hotplug net INTERFACE=dpsta ACTION=add SEQNUM=275
hotplug net INTERFACE=agg ACTION=add SEQNUM=269
hotplug net INTERFACE=fwd1 ACTION=add SEQNUM=267
PCI_PROBE:  bus 1, slot 0,vendor 14E4, device 4365(good PCI location)
PCI: Enabling device 0002:01:00.0 (0140 -> 0142)
dhd_attach(): thread:dhd_watchdog_thread:7d started
Dongle Host Driver, version 1.363.2 (r665954)
Compiled in drivers/net/wireless/bcmdhd on May 18 2021 at 20:55:17
Register interface [eth1]  MAC: 00:90:4c:18:d2:34hotplug net INTERFACE=eth1 ACTION=add SEQNUM=278
load_wl(): insmod dhd24 instance_base=1 dhd_msg_level=0.
load_wl(): end.
1: check_action 0: 1(preinit)
*** ubifs: jffs2 (5, 67108864)
*** ubifs: attach (/dev/mtd5, 1260662)
*** ubifs: jffs2 0, 0, 63741952
<rc_service> [i:service] 290:notify_rc start_skipd/jffs/.asusrouter killdon: errno: 3 pid 258
_ifconfig: name=eth0 flags=1043 IFUP addr= netmask=
hotplug net INTERFACE=vlan1 ACTION=add SEQNUM=292
hotplug net INTERFACE=vlan2 ACTION=add SEQNUM=294
update_lan_state(lan_, 0, 0)
generate_wl_para(0x0fe0): unit 0 subunit -1
generate_wl_para(0x1390): set vhtmode -1
generate_wl_para(0x1486): bw: 1
generate_wl_para(0x1488): chanspec: 0
generate_wl_para(0x1489): bw_cap: 1
generate_wl_para(0x148f): obss_coex: 0
generate_wl_para(0x0fe0): unit 1 subunit -1
eth2: WLC_GET_VAR(cap): No such device
eth2: cmd=39 (errno 19): No such device
generate_wl_para(0x13b1): set vhtmode 1
generate_wl_para(0x1486): bw: 0
generate_wl_para(0x1488): chanspec: 0
generate_wl_para(0x1489): bw_cap: 3
generate_wl_para(0x148f): obss_coex: 0
_ifconfig: name=fwd0 flags=0000  addr= netmask=
_ifconfig: name=fwd0 flags=1343 IFUP addr= netmask=
_ifconfig: name=fwd1 flags=0000  addr= netmask=
_ifconfig: name=fwd1 flags=1343 IFUP addr= netmask=
vlan1: cmd=14 (errno 95): Operation not supported
_ifconfig: name=vlan1 flags=1243 IFUP addr= netmask=
_ifconfig: name=eth1 flags=1243 IFUP addr= netmask=
generate_wl_para(0x0fe0): unit 0 subunit -1
generate_wl_para(0x1390): set vhtmode -1
generate_wl_para(0x1486): bw: 1
generate_wl_para(0x1488): chanspec: 0
generate_wl_para(0x1489): bw_cap: 1
generate_wl_para(0x148f): obss_coex: 0
generate_wl_para(0x0fe0): unit 0 subunit 1
generate_wl_para(0x0fe0): unit 0 subunit 2
generate_wl_para(0x0fe0): unit 0 subunit 3
generate_wl_para(0x0fe0): unit 0 subunit 4
hotplug net INTERFACE=br0 ACTION=add SEQNUM=296
eth2: cmd=14 (errno 19): No such device
_ifconfig: name=eth2 flags=1243 IFUP addr= netmask=
eth2: No such device
start_lan: setting MAC address of bridge br0 as 2C:B2:1A:5D:63:D8
_ifconfig: name=br0 flags=1243 IFUP addr=192.168.50.1 netmask=255.255.255.0
_ifconfig: name=lo flags=1043 IFUP addr=127.0.0.1 netmask=255.0.0.0
_ifconfig: name=lo:0 flags=1043 IFUP addr=127.0.1.1 netmask=255.0.0.0
route_manip: cmd=ADD name=lo addr=127.0.0.0 netmask=255.0.0.0 gateway=0.0.0.0 metric=0
lo: File exists
update_lan_state(lan_, 2, 0)
nat_rule: stop_nat_rules 1.
stop_nat_rules: apply the redirect_rules state 0 ret 0
eth2: WLC_GET_VAR(chanspecs): No such device
failed to get valid chanspec list
: WLC_GET_VAR(chanspecs): No such device
failed to get valid chanspec list
: WLC_GET_VAR(chanspecs): No such device
failed to get valid chanspec list
: WLC_GET_VAR(chanspecs): No such device
failed to get valid chanspec listset exclchans base:
0:[0x100c,0x190a,0x100d,0x190b,0x100e,0x190c]
1:[0xd0a5]
2:[]
rc: ==> binding interface(vlan1,eth1,eth2,wds0.*,wds1.*,wds2.*) for lldpd
# wanduck: Got LAN(-1) information:
wanduck: delay 1 seconds before the first detect...
wanduck: delay 2 seconds before the first detect...
wanduck: delay 3 seconds before the first detect...
start_lan 2325
vlan1: cmd=14 (errno 95): Operation not supported
eth2: cmd=14 (errno 19): No such device
wanduck: delay 4 seconds before the first detect...
[register_feature] blockfile registered
[register_feature] chknvram registered
[register_feature] misc registered
[are_all_sig_file_valid] Local version file is invalid!
[init] Remove all invalid files
[1 preinit:start_dnsmasq +19] begin
[1 preinit:stop_dnsmasq +19] begin
[1 preinit:stop_stubby +19] begin
[1 preinit:stop_stubby +19] end
[1 preinit:stop_dnsmasq +19] end
[1 preinit:start_stubby +19] begin
wanduck: delay 5 seconds before the first detect...
[1 preinit:start_dnsmasq +20] end
start_lan_port(0) 1
amaslib_lease_main():: add, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
vendor class=MSFT 5.0
### onboarding model=RT-AC3100, reboot_time=120, connection_timeout=60, traffic_timeout=60
TZ watchdog
msgget ok
wanduck(0): NC send SYS_WAN_MODEM_OFFLINE_EVENT.# Enable direct rule
get_all_pc_list, enabled_str=, enabled=0.
disk_monitor: starting...
disk_monitor: day=5, week=6, time=13:5.
disk_monitor: decide if scan the target...
disk_monitor: 0: wait_second=36000...
disk_monitor: 1: wait_second=36000...
disk_monitor: wait_second=36000...
disk_monitor: Pause...get_all_pc_list, enabled_str=, enabled=0.
Couldn't get the enabled rules of Parental-control correctly!
[bwdpi check] starting...
rc: ==> binding interface(vlan1,eth1,eth2,wds0.*,wds1.*,wds2.*) for lldpd
rc: ==> binding interface match lldpd_bind_ifnames(vlan1,eth1,eth2,wds0.*,wds1.*,wds2.*)...
start_wan: start_wan_if(0)!
[1 preinit:start_wan_if +22] unit=0.
update_wan_state(wan0_, 0, 0)
convert_wan_nvram(wan0_)
_ifconfig: name=eth0 flags=0000  addr= netmask=
** wan_ifname: eth0 is NOT UP
_ifconfig: name=eth0 flags=1043 IFUP addr= netmask=
update_wan_state(wan0_, 1, 0)
start_wan_if(0x0767): ifup:eth0
_ifconfig: name=eth0 flags=1043 IFUP addr= netmask=
start_wan_if(0x077a): start auth:0
start_auth:: done
start_wan_if(0x077e): start udhcpc:eth0, 0
start_wan_if(): End.
udhcpc_wan:: deconfig
_ifconfig: name=eth0 flags=1043 IFUP addr=0.0.0.0 netmask=
wan_down(eth0)
wan_down(eth0): .
stop_auth:: done
route_manip: cmd=DEL name=eth0 addr=0.0.0.0 netmask=0.0.0.0 gateway=(null) metric=0
update_wan_state(wan0_, 3, 0)
update_wan_state(wan0_, 4, 3)
udhcpc:: deconfig done
amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
amaslib_lease_main():: done
vendor class=
udhcpc_wan:: bound
_ifconfig: name=eth0 flags=1043 IFUP addr=0.0.0.0 netmask=
_ifconfig: name=eth0 flags=1043 IFUP addr=192.168.1.124 netmask=255.255.255.0
wan_up(eth0)
update_wan_state(wan0_, 2, 0)
writting prerouting eth0 192.168.1.124 eth0 0.0.0.0 br0 192.168.50.1
get_all_pc_list, enabled_str=, enabled=0.
Couldn't get the enabled rules of Parental-control correctly!
nat_rule: start_nat_rules 1.
start_nat_rules: apply the nat_rules (/tmp/nat_rules_eth0_eth0) state 3 ret 0
[728 udhcpc:filter_setting +23] writing Internet Control
Couldn't get the enabled rules of Parental-control correctly!
Couldn't get the enabled rules of Parental-control correctly!
get_all_pc_list, enabled_str=, enabled=0.
Couldn't get the enabled rules of Parental-control correctly!
Couldn't get the enabled rules of Parental-control correctly!
[728 udhcpc:filter_setting +23] write porttrigger
eth2: WLC_GET_VAR(fabid): No such device
Enable USB power.
Start USB with the original procedure.
start_usb
no tune_bdflush
amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
amaslib_lease_main():: done
vendor class=MSFT 5.0
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
start_auth:: done
add_multi_routes: running...
amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
amaslib_lease_main():: done
vendor class=
<rc_service> [i:udhcpc] 728:notify_rc stop_ntpd<rc_service> [i:udhcpc] 728:notify_rc start_ntpd728: wait for previous script(14/15): stop_ntpd 728 udhcpc.
hotplug net INTERFACE=zt6ovuxnwx ACTION=add SEQNUM=376
error adding IE: -19
728: wait for previous script(13/15): stop_ntpd 728 udhcpc.
**** k3.c[start_k3screen(212)] k3screen: start
728: wait for previous script(12/15): stop_ntpd 728 udhcpc.
**** k3.c[start_k3screen(216)] k3screen: ok
**** k3.c[k3_init_done(197)] softcenter: init done# Disable direct rule(D2C)......
[1 preinit:init_main +26] recv signal 10 from pid [290:] (from user)
cmd[0]=stop_ntpd
[1 preinit:handle_notifications +27] running: 1 ntpd
handle_notifications() end
nat_rule: start_nat_rules 3.
[1 preinit:init_main +27] recv signal 10 from pid [728:/tmp/udhcpc] (from user)
cmd[0]=start_ntpd
[1 preinit:handle_notifications +27] running: 2 ntpd
stop igmpproxy
handle_notifications() end
wan_up: wan_mac=D4:EE:07:00:00:00.
<rc_service> [i:udhcpc] 728:notify_rc stop_samba[1 preinit:init_main +29] recv signal 10 from pid [728:/tmp/udhcpc] (from user)
cmd[0]=stop_samba
[1 preinit:handle_notifications +29] running: 1 samba
<rc_service> [i:udhcpc] 728:notify_rc start_samba728: wait for previous script(29/30): stop_samba 728 udhcpc.
amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GTgro disabled
handle_notifications() end
amaslib_lease_main():: done
vendor class=
wan_up(eth0): done.
udhcpc:: bound done
[1 preinit:init_main +30] recv signal 10 from pid [728:/tmp/udhcpc] (from user)
cmd[0]=start_samba
[1 preinit:handle_notifications +30] running: 2 samba
[1 preinit:start_dnsmasq +30] begin
[1 preinit:stop_dnsmasq +30] begin
killall_tk: waiting name=dnsmasq n=9
killall_tk: waiting name=dnsmasq n=8
killall_tk: waiting name=dnsmasq n=7
killall_tk: waiting name=dnsmasq n=6
killall_tk: waiting name=dnsmasq n=5
[1 preinit:stop_stubby +31] begin
[1 preinit:stop_stubby +31] end
[1 preinit:stop_dnsmasq +31] end
[1 preinit:start_stubby +31] begin
<rc_service> [i:ntpd_synced] 1171:notify_rc restart_diskmon1171: wait for previous script(14/15): start_samba 728 .
[1 preinit:start_dnsmasq +32] end
handle_notifications() end
wanduck(0): NC send SYS_WAN_UNPUBLIC_IP_EVENT.
[1 preinit:init_main +32] recv signal 10 from pid [1171:/sbin/ntpd_synced] (from user)
cmd[0]=restart_diskmon
[1 preinit:handle_notifications +32] running: 3 diskmon
killall_tk: waiting name=disk_monitor n=9
killall_tk: waiting name=disk_monitor n=8
killall_tk: waiting name=disk_monitor n=7
disk_monitor: Finish!
killall_tk: waiting name=disk_monitor n=6
killall_tk: waiting name=disk_monitor n=5
handle_notifications() end
amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
amaslib_lease_main():: done
vendor class=
disk_monitor: starting...
disk_monitor: day=4, week=0, time=1:19.
disk_monitor: decide if scan the target...
disk_monitor: 0: wait_second=2460...
disk_monitor: 1: wait_second=2460...
disk_monitor: wait_second=2460...
disk_monitor: Pause...amaslib_lease_main():: old, 2a:46:6f:04:33:2f, 192.168.50.124, USER-20220112GT
amaslib_lease_main():: done
vendor class=
RAST 34: ROAMAST Start...
RAST 34: ROAMING Start...
[rast_init_bssinfo]: WIF[eth1], idx[0]
rssi threshold: [0]
rssi hit count: [2]
idle period: [10]
idle rate: [100]
[WARNING] get instance eth2 error!!!
[rast_init_bssinfo]: WIF[eth2], idx[1]
rssi threshold: [0]
rssi hit count: [6]
idle period: [20]
idle rate: [10]
[rast_init_bssinfo]: TotalWI[2] RAST 35: [WARNING] eth2 get macmode error!!!
RAST 35: ipc accept socket...
RAST 36: internal ipc accept socket...
[Mastiff]exit.

区别是什么呢?都是能实时看到日志并能控制,只是这个是默认的系统启动.

查看全文

http://www.taodudu.cc/news/show-6128259.html

WordPress更新方法，防止 WP 官网 429 导致更新失败
WP——1
3web wp
11.27 WP
WordPress文章标题显示汉字方法
WordPress中文汉字用户名不能注册怎么办？
HNCTF wp
【GDOUCTF2023】wp
web WP
UUCTF WP
sp wp
JS汉字转拼音，超级实用
wp手机开发之获取汉字拼音的首字母
docker pull redis 镜像
docker-redis
kettle 9.x 版本连接资源库，资源库灰色
KIcad 库管理
Kotlin GreenDao
超级光棍节，你想好怎么过了吗？来聆听大师的演讲吧
Docker搭建 Nginx+PHP+MySQL 环境并部署WordPress实践
Jquery--一个form中两个submit事件如何进行区分
KDD
kettle-新建资源库connect资源库灰色解决
树库介绍
KiCAD库
caldera
AidLux
git上传到阿里云code
java.net.MalformedURLException异常说明
Endnote导入下载好的引用文件

[原创]裴讯K3救砖TTL竟然进入openwrt终端无法进入CFE-强力救砖相关推荐

cfe刷机教程斐讯k3_斐讯K3全版本刷机教程2019-不用降级开telnet拆机TTL
斐讯K3由于更新了新的固件,想要刷入第三方固件,之前的刷机方法可能不行了,这里分享2019年最新的斐讯K3刷机方法,不用降级,不用开telnet,不用拆机TTL,非常的方便且快捷,下面就给大家说说怎么 ...
玩转斐讯K3详细刷机——直接刷LEDE
版权声明:本文为博主原创文章,未经博主允许不得转载.博客不用于商业活动,博主对博客的使用,拥有最终解释权本文为原创作品,未经本人同意,禁止转载,禁止用于商业用途!本人对博客使用拥有最终解释权欢迎关 ...
斐讯k3怎么设置虚拟服务器,斐讯 K3 无线路由器无线中继设置教程
斐讯 K3 无线路由器无线中继设置教程- 2017-04-12 1.斐讯K3默认的IP地址是192.168.2.1,DHCP服务开启.这些设置好后,在"功能设置"里点开" ...
斐讯k3怎么设置虚拟服务器,斐讯K3路由器无线中继怎么设置？
斐讯K3这款外包装采用纯黑配色.高档材质,简约设计强大的无线性能,若用来做无线中继,必定有非常好的的网速,如果不考虑功耗,那么用来当作"无线网卡"使用,也是不错的选择.要发挥出最大 ...
斐讯路由器设置linux,Windows10系统怎么给斐讯K3路由器开启Telnet
斐讯K3路由器在刷机之前大神都会告诫我们最好给K3开启Telnet,那么Windows 10系统最简单的开启Telnet的方法是什么呢?下面一起来看看. 对于Windows10来说最强大的就是兼容各种 ...
斐讯k3搭建nginx+php+MariaDB(mysql )的教程
安装nginx+php+MariaDB 以前用k3安装了onmp,中间踩了不少坑.以前发到贴吧的,现在发过来记录一下,顺便给大家参考一下. 斐讯k3性能比较强,拿来建小型网站还是可以的.但是内置储存太 ...
讯wifi_裴讯路由器登录密码
很多人在买了裴讯路由器后,不知道裴讯路由器的登录密码是什么,学习啦小编为大家整理了裴讯路由器登录密码的相关内容,供大家参考阅读! 裴讯路由器登录密码一般来说,裴讯路由器的用户名和密码都是默认的: 默 ...
树莓派挂载斐讯K3上SMB共享的移动硬盘文件
最近在使用树莓派时录制视频时,发现录制上3小时左右的视频呢,就用到了差不多3GB的储存空间,对于我的树莓派8GB的SD卡来说呢肯定是不适宜的.所以我就萌发出了在树莓派上挂载斐讯路由器上的移动硬盘来用作 ...
斐讯K3 在openwrt上如何手动安装阿里云盘aliyun-dav
感觉网络上很多的东西,不那么复杂的,是没有教程让它变复杂. 斐讯K3 在openwrt上如何手动安装阿里云盘aliyun-dav,这很正常的需求吧,只有固件打包在里面的,没有手动安装的. 于是,本人不 ...

[原创]裴讯K3救砖TTL竟然进入openwrt终端无法进入CFE-强力救砖

相关文章：

[原创]裴讯K3救砖TTL竟然进入openwrt终端无法进入CFE-强力救砖相关推荐

最新文章

热门文章