Loading "flash:/c2960-lanbase-mz.122-25.FX.bin"...
######################### [OK]Restricted Rights LegendUse, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.cisco Systems, Inc.170 West Tasman DriveSan Jose, California 95134-1706Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(25)FX, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Wed 12-Oct-05 22:05 by pt_team
Image text-base: 0x80008098, data-base: 0x814129C4Cisco WS-C2960-24TT (RC32300) processor (revision C0) with 21039K bytes of memory.24 FastEthernet/IEEE 802.3 interface(s)
2 Gigabit Ethernet/IEEE 802.3 interface(s)63488K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address       : 000B.BE37.8027
Motherboard assembly number     : 73-9832-06
Power supply part number        : 341-0097-02
Motherboard serial number       : FOC103248MJ
Power supply serial number      : DCA102133JA
Model revision number           : B0
Motherboard revision number     : C0
Model number                    : WS-C2960-24TT
System serial number            : FOC1033Z1EY
Top Assembly Part Number        : 800-26671-02
Top Assembly Revision Number    : B0
Version ID                      : V02
CLEI Code Number                : COM3K00BRA
Hardware Board Revision Number  : 0x01Switch   Ports  Model              SW Version              SW Image
------   -----  -----              ----------              ----------
*    1   26     WS-C2960-24TT      12.2                    C2960-LANBASE-MCisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(25)FX, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Wed 12-Oct-05 22:05 by pt_teamPress RETURN to get started!%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to upSwitch>en
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.Switch(config)#hostname SW1
l
SW1(config)#interface vlan 1
SW1(config-if)#ip add 192.168.1.1 255.255.255.0SW1(config-if)#no shutdown SW1(config-if)#
%LINK-5-CHANGED: Interface Vlan1, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to upSW1(config-if)#end
SW1#
%SYS-5-CONFIG_I: Configured from console by consoleSW1#ping 192.168.1.2Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds:
.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 0/0/1 msSW1#wr
Building configuration...
[OK]SW1#copy startup-config tftp:
Address or name of remote host []? 192.168.1.2
Destination filename [SW1-confg]? Writing startup-config...!!
[OK - 1055 bytes]1055 bytes copied in 0 secs

SW1#conf t
Enter configuration commands, one per line.  End with CNTL/Z.SW1(config)#hostname  testnametestname(config)#end
testname#
%SYS-5-CONFIG_I: Configured from console by consoletestname#copy tftp: running-config
Address or name of remote host []? 192.168.1.2
Source filename []? SW1-confg
Destination filename [running-config]? Accessing tftp://192.168.1.2/SW1-confg...
Loading SW1-confg from 192.168.1.2: !
[OK - 1055 bytes]1055 bytes copied in 0 secs
SW1#
%SYS-5-CONFIG_I: Configured from console by consoleSW1#
SW1#
SW1#

Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#host R1
R1(config)#no ip domain-loR1(config)#line console 0R1(config-line)#logging synR1(config-line)#exec-timeout 00R1(config-line)#inter fa0/0
R1(config-if)#ip add 192.168.1.1 255.255.255.0R1(config-if)#no shutdown R1(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upR1(config-if)#end
R1#
%SYS-5-CONFIG_I: Configured from console by consoleR1#ping 192.168.1.2Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds:
.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 0/0/1 msR1#wr
Building configuration...
[OK]R1#copy running-config tftp:
Address or name of remote host []? 192.168.1.2
Destination filename [R1-confg]? Writing running-config...!!
[OK - 632 bytes]632 bytes copied in 0.001 secs (632000 bytes/sec)
R1#