GNSS NMEA-0183 协议
这是从trimble公司官网上copy下来的关于NMEA-183协议的相关说明，可供参考：
NMEA-0183 messages: Common message elements
Each message contains:
a message ID consisting of $GP followed by the message type. For example, the message ID of the GGA message is $GPGGA.
a comma.
a number of fields, depending on the message type, separated by commas.
an asterisk.
a checksum value.
The following example shows a simple message with a message ID ($GPGGA), followed by 13 fields and a checksum value:
$GPGGA,172814.0,3723.46587704,N,12202.26957864,W,2,6,1.2,18.893,M,-25.669,M,2.0,0031*4F
Message values
NMEA messages that the receiver generates contains the following values:
Value Description
Latitude and Longitude
Latitude is represented as ddmm.mmmm and longitude is represented as dddmm.mmmm, where:
dd or ddd is degrees
mm.mmmm is minutes and decimal fractions of minutes
Direction Direction (north, south, east, or west) is represented by a single character: N , S , E , or W.
Time
Time values are presented in Universal Time Coordinated (UTC) and are represented as hhmmss.ss, where:
hh is hours, from 00 through 23
mm is minutes
ss.ss is seconds with variable length decimal-fraction of seconds
########
Message Function
ADV Position and satellite information for RTK network operations
DTM Datum reference information
GBS GNSS satellite fault detection (RAIM support)
GGA Time, position, and fix related data
GLL Position data: position fix, time of position fix, and status
GNS GNS Fix data
GRS GRS range residuals
GSA GPS DOP and active satellites
GST Position error statistics
GSV Number of SVs in view, PRN, elevation, azimuth, and SNR
HDT Heading from True North
LLQ Leica local position and quality
PFUGDP A proprietary message containing information about the type of positioning system, position, number of satellites and position statistics
PTNL,AVR Time, yaw, tilt, range, mode, PDOP, and number of SVs for Moving Baseline RTK
PTNL,BPQ Base station position and position quality indicator
PTNL,DG L-band corrections and beacon signal strength and related information
PTNL,GGK Time, position, position type, and DOP values
PTNL,PJK Time, position, position type, and DOP values
PTNL,PJT Projection type
PTNL,VGK Time, locator vector, type, and DOP values
PTNL,VHD Heading Information
RMC Position, Velocity, and Time
ROT Rate of turn
VTG Actual track made good and speed over ground
ZDA UTC day, month, and year, and local time zone offset
##########
1. AVD
Position and satellite information for RTK network operations
The messages alternate between subtype 110 and 120.
ADV subtype 110 message fields
An example of the ADV subtype 110 message string is:
$PGPPADV,110,39.88113582,-105.07838455,1614.125*1M
Field Meaning
0 Message ID $PGPPADV
1 Message subtype 110
2 Latitude
3 Longitude
4 Ellipsoid height
6 Elevation of second satellite, in degrees, 90° maximum
7 Azimuth of second satellite, degrees from True North, 000° through 359°
8 The checksum data, always begins with *
ADV subtype 120 message fields
An example of the ADV subtype 120 message string is:
$PGPPADV,120,21,76.82,68.51,29,20.66,317.47,28,52.38,276.81,22,42.26,198.96*5D
Field Meaning
0 Message ID $PGPPADV
1 Message subtype 120
2 First SV PRN number
3 Elevation of first satellite, in degrees, 90° maximum
4 Azimuth of first satellite, degrees from True North, 000° through 359°
5 Second SV PRN number
6 Elevation of second satellite, in degrees, 90° maximum
7 Azimuth of second satellite, degrees from True North, 000° through 359°
8 The checksum data, always begins with *
########
2. DTM
Datum reference information
The DTM message string identifies the datum used. An example of the GPDTM message string is:
$GPDTM,xxx,x,xx.xxxx,x,xx.xxxx,x,,xxx*hh<CR><LF>
DTM message fields
Field Meaning
1 Local datum code (xxx):
W84 – WGS84
W72 – WGS72
S85 – SGS85
P90 – PE90
999 – User defined
IHO datum code
2 Local datum sub code (x)
3 Latitude offset in minutes (xx.xxxx)
4 Latitude offset mark (N: +, S: -) (x)
5 Longitude offset in minutes (xx.xxxx)
6 Longitude offset mark (E: +, W: -) (x)
7 Altitude offset in meters. Always null
8 Datum (xxx):
W84 – WGS84
W72 – WGS72
S85 – SGS85
P90 – PE90
999 – User defined
IHO datum code
9 Checksum
#########
3. GBS
GNSS satellite fault detection (RAIM support)
An example of the GBS message string is:
$GPGBS,015509.00,-0.031,-0.186,0.219,19,0.000,-0.354,6.972*4D
GBS message fields
Field Meaning
0 Message ID $--GBS
1 UTC of position fix
2 Expected error in latitude, in meters, due to bias, with noise = 0
3 Expected error in longitute, in meters, due to bias, with noise = 0
4 Expected error in altitude, in meters, due to bias, with noise = 0
5 ID number of most likely failed satellite
6 Probability of missed detection of most likely failed satellite
7 Estimate of bias, in meters, on the most likely failed satellite
8 Standard deviation of bias estimate
9 The checksum data, always begins with *
########
4. GGA
Time, position, and fix related data
An example of the GBS message string is:
$GPGGA,172814.0,3723.46587704,N,12202.26957864,W,
2,6,1.2,18.893,M,-25.669,M,2.0,0031*4F
Note – The data string exceeds the NMEA standard length.
GGA message fields
Field Meaning
0 Message ID $GPGGA
1 UTC of position fix
2 Latitude
3 Direction of latitude:
N: North
S: South
4 Longitude
5 Direction of longitude:
E: East
W: West
6 GPS Quality indicator:
0: Fix not valid
1: GPS fix
2: Differential GPS fix, OmniSTAR VBS
4: Real-Time Kinematic, fixed integers
5: Real-Time Kinematic, float integers, OmniSTAR XP/HP or Location RTK
7 Number of SVs in use, range from 00 through to 24+
8 HDOP
9 Orthometric height (MSL reference)
10 M: unit of measure for orthometric height is meters
11 Geoid separation
12 M: geoid separation measured in meters
13 Age of differential GPS data record, Type 1 or Type 9. Null field when DGPS is not used.
14 Reference station ID, range 0000-4095. A null field when any reference station ID is selected and no corrections are received1.
15 The checksum data, always begins with *
###########
5. GLL
Position data: position fix, time of position fix, and status
An example of the GLL message string is:
$GPGSA,A,3,3,6,27,19,9,14,21,22,18,15,,,2.1,1.0,1.8*03
GLL message fields
Field Meaning
0 Message ID $GPGLL
1 Latitude in dd mm,mmmm format (0-7 decimal places)
2 Direction of latitude N: North S: South
3 Longitude in ddd mm,mmmm format (0-7 decimal places)
4 Direction of longitude E: East W: West
5 UTC of position in hhmmss.ss format
6 Fixed text "A" shows that data is valid
7 The checksum data, always begins with *
#########
6. GNS
GNSS fix data
GNSS capable receivers will always output this message with the GN talker ID
GNSS capable receivers will also output this message with the GP and/or GL talker ID when using more than one constellation for the position fix
An example of the GNS message output from a GNSS capable receiver is:
$GNGNS,014035.00,4332.69262,S,17235.48549,E,RR,13,0.9,25.63,11.24,,*70<CR><LF>
$GPGNS,014035.00,,,,,,8,,,,1.0,23*76<CR><LF>
$GLGNS,014035.00,,,,,,5,,,,1.0,23*67<CR><LF>
GNS message fields
Field Meaning
0 Message ID $--GNS
Talker ID can be:
GP: To provide information specific to the GPS constellation when more than one constellation is used for the differential position fix
GL: To provide information specific to the GLONASS constellation when more than one constellation is used for the differential position fix
GN: GNSS position fix from more than one constellation (eg. GPS + GLONASS)
1 UTC of position fix
2 Latitude
3 Direction of latitude:
N: North
S: South
4 Longitude
5 Direction of longitude:
E: East
W: West
6 Mode indicator:
Variable character field with one character for each supported constellation.
First character is for GPS
Second character is for GLONASS
Subsequent characters will be added for new constellation
Each character will be one of the following:
N = No fix. Satellite system not used in position fix, or fix not valid
A = Autonomous. Satellite system used in non-differential mode in position fix
D = Differential (including all OmniSTAR services). Satellite system used in differential mode in position fix
P = Precise. Satellite system used in precision mode. Precision mode is defined as: no deliberate degradation (such as Selective Availability) and higher resolution code (P-code) is used to compute position fix
R = Real Time Kinematic. Satellite system used in RTK mode with fixed integers
F = Float RTK. Satellite system used in real time kinematic mode with floating integers
E = Estimated (dead reckoning) Mode
M = Manual Input Mode
S = Simulator Mode
7 Number of SVs in use, range 00–99
8 HDOP calculated using all the satellites (GPS, GLONASS, and any future satellites) used in computing the solution reported in each GNS sentence.
9 Orthometric height in meters (MSL reference)
10 Geoidal separation in meters - the difference between the earth ellipsoid surface and mean-sea-level (geoid) surface defined by the reference datum used in the position solution
“-” = mean-sea-level surface below ellipsoid.
11 Age of differential data - Null if talker ID is GN, additional GNS messages follow with GP and/or GL Age of differential data
12 Reference station ID(When using OmniSTAR services, the Reference Station ID indicates the following services: VBS 100=VBS; 1000=HP; 1001 = HP/ XP (Orbits) ; 1002 = HP/G2 (Orbits); 1008 = XP (GPS); 1012 = G2 (GPS); 1013 = G2 (GPS/GLONASS); 1014 = G2 (GLONASS); 1016 = HP/XP (GPS); 1020 = HP/G2 (GPS) ; 1021 = HP/G2 (GPS/GLONASS). ), range 0000-4095
- Null if talker ID is GN, additional GNS messages follow with GP and/or GL Reference station ID
13 The checksum data, always begins with *
Note – If a user-defined geoid model, or an inclined plane is loaded into the receiver, then the height output in the NMEA GNS string is always the orthometric height (height above a geoid). The orthometric height is output even if no user-defined geoid is loaded (there is a simplified default geoid in the receiver), or if a user-defined geoid is loaded, or if an inclined plane is used.
##############
7. GRS
GRS range residuals
The GRS message is used to support the Receiver Autonomous Integrity Monitoring (RAIM).
Note – Because the contents of this NMEA message do not change significantly during a one-second interval, the receiver outputs this message at a maximum rate of 1 Hz.
An example of the GRS message string is:
$GPGRS,220320.0,0,-0.8,-0.2,-0.1, -0.2,0.8,0.6,,,,,,,*55
GRS message fields
Field Meaning
0 Message ID $GPGRS
1 UTC of GGA position fix
2 Residuals
0: Residuals used to calculate position given in the matching GGA line
1: Residuals recomputed after the GGA position was computed
3–14 Range residuals for satellites used in the navigation solution, in meters
#############
8.GSA
GPS DOP and active satellites
An example of the GSA message string is:
$GPGSA,<1>,<2>,<3>,<3>,,,,,<3>,<3>,<3>,<4>,<5>,<6>*<7><CR><LF>
GSA message fields
Field Meaning
0 Message ID $GPGSA
1 Mode 1, M = manual, A = automatic
2 Mode 2, Fix type, 1 = not available, 2 = 2D, 3 = 3D
3 PRN number, 01 through 32 for GPS, 33 through 64 for SBAS, 64+ for GLONASS
4 PDOP: 0.5 through 99.9
5 HDOP: 0.5 through 99.9
6 VDOP: 0.5 through 99.9
7 The checksum data, always begins with *
############
9.GST
Position error statistics
An example of the GST message string is:
$GPGST,172814.0,0.006,0.023,0.020,273.6,0.023,0.020,0.031*6A
The Talker ID ($--) will vary depending on the satellite system used for the position solution:
$GP - GPS only
$GL - GLONASS only
$GN - Combined
GST message fields
Field Meaning
0 Message ID $GPGST
1 UTC of position fix
2 RMS value of the pseudorange residuals; includes carrier phase residuals during periods of RTK (float) and RTK (fixed) processing
3 Error ellipse semi-major axis 1 sigma error, in meters
4 Error ellipse semi-minor axis 1 sigma error, in meters
5 Error ellipse orientation, degrees from true north
6 Latitude 1 sigma error, in meters
7 Longitude 1 sigma error, in meters
8 Height 1 sigma error, in meters
9 The checksum data, always begins with *
###############
10. GSV
Satellite information
The GSV message string identifies the number of SVs in view, the PRN numbers, elevations, azimuths, and SNR values. An example of the GSV message string is:
$GPGSV,4,1,13,02,02,213,,03,-3,000,,11,00,121,,14,13,172,05*67
GSV message fields
Field Meaning
0 Message ID $GPGSV
1 Total number of messages of this type in this cycle
2 Message number
3 Total number of SVs visible
4 SV PRN number
5 Elevation, in degrees, 90° maximum
6 Azimuth, degrees from True North, 000° through 359°
7 SNR, 00 through 99 dB (null when not tracking)
8–11 Information about second SV, same format as fields 4 through 7
12–15 Information about third SV, same format as fields 4 through 7
16–19 Information about fourth SV, same format as fields 4 through 7
20 The checksum data, always begins with *
#############
11. HDT
Heading from True North
An example of the HDT string is:
$GPHDT,123.456,T*00
Heading from true north message fields
Field Meaning
0 Message ID $GPHDT
1 Heading in degrees
2 T: Indicates heading relative to True North
3 The checksum data, always begins with *
###########
12. LLQ
Leica local position and quality
Field Meaning
0 Message ID $GPLLQ
1 hhmmss.ss - UTC time of position
2 ddmmyy - UTC date
3 xxx.xxx - Grid easting (meters)
4 M - Meter, fixed text
5 xxxx.xxxx - Grid northing (meters)
6 M - Meter, fixed text
7 x - GPS quality. 0 = not valid. 1 = GPS Nav Fix. 2 = DGPS Fix. 3 = RTK Fix.
8 x - Number of satellites used in computation
9 xx.xx - Position quality (meters)
10 xxxx.xxxx - Height (meters)
11 M - Meter, fixed text
*hh - checksum
<CR> - carriage return
<LF> - Line feed
########
13. PFUGDP
Proprietary Fugro positioning message
The PFUGDP message is a proprietary message containing information about the type of positioning system, position, number of satellites and position statistics.
An example of the PFUGDP message string is:
$PFUGDP,GP,hhmmss.ss,ddmm.mmmmm,D,dddmm.mmmmm,D,sv,QI,DD,It,In,dir,ht*XX
PFUGDP message fields
Field Meaning
1 Type of positioning system (GP = GPS, GL = GLONASS, GN = GNSS)
2 UTC of position fix
3–4 Latitude in DDMM,MMMMM format, N (North) or S (South)
5–6 Latitude in DDMM,MMMMM format, E (East) or W (West)
7 Number of satellites in use
8 DPVOA (UKOOA) quality indicator (0–9)
9 DGNSS mode indicator (as defined for NMEA standard telegram $_GNS)
10 Error ellipse standard deviation semi-major axis, in meters
11 Error ellipse standard deviation semi-minor axis, in meters
12 Direction of the semi-major axis of the error ellipse, in degrees
13 RMS value of the standard deviation of the range inputs to the navigation process
##########
14. PTNL,AVR
Time, yaw, tilt, range for moving baseline RTK
An example of the PTNL,AVR message string is:
$PTNL,AVR,181059.6,+149.4688,Yaw,+0.0134,Tilt,,,60.191,3,2.5,6*00
AVR message fields
Field Meaning
0 Message ID $PTNL,AVR
1 UTC of vector fix
2 Yaw angle in degrees
3 Yaw
4 Tilt angle in degrees
5 Tilt
6 Reserved
7 Reserved
8 Range in meters
9 GPS quality indicator:
0: Fix not available or invalid
1: Autonomous GPS fix
2: Differential carrier phase solution RTK (Float)
3: Differential carrier phase solution RTK (Fix)
4: Differential code-based solution, DGPS
10 PDOP
11 Number of satellites used in solution
12 The checksum data, always begins with *
###########
15. PTNL,BPQ
Base station position and quality indicator
This message describes the base station position and its quality. It is used when the moving base antenna position and quality are required on one serial port (along with a heading message) from a receiver in heading mode, typically the SPSx61.
An example of the PTNL,BPQ message string is:
$PTNL,BPQ,224445.06,021207,3723.09383914,N,12200.32620132,W,EHT-5.923,M,5*
BPQ message fields
Field Meaning
0 Talker ID
1 BPQ
2 UTC time of position fix, in hhmmss.ss format. Hours must be two numbers, so may be padded, for example, 7 is shown as 07.
3 UTC date of position fix, in ddmmyy format. Day must be two numbers, so may be padded, for example, 8 is shown as 08.
4 Latitude, in degrees and decimal minutes (ddmm.mmmmmmm)
5 Direction of latitude:
N: North
S: South
6 Longitude, in degrees and decimal minutes (dddmm.mmmmmmm). Should contain 3 digits of ddd.
7 Direction of longitude:
E: East
W: West
8 Height Ellipsoidal height of fix (antenna height above ellipsoid). Must start with EHT.
9 M: ellipsoidal height is measured in meters
10 GPS quality indicator:
0: Fix not available or invalid
1: Autonomous GPS fix
2: Differential SBAS, or OmniSTAR VBS
4: RTK Fixed
5: OmniSTAR XP, OmniSTAR HP, Float RTK, or Location RTK
11 The checksum data, always begins with *
##########
16. PTNL,DG
L-band corrections and beacon signal strength and related information
This message, $PTNLDG, is a Trimble-created message. It outputs the L-band and beacon signal strength and other information.
Examples of the PTNL,DG message string are:
For beacon DG message: $PTNLDG,44.0,33.0,287.0,100,0,4,1,0,,,*3E
For L-band DG message: $PTNLDG,124.0,10.5,1557855.0,1200,2,4,0,3,,,*3C
DG message fields
Field Meaning
0 Talker ID
1 Signal strength
2 SNR in db
3 Signal frequency in kHz
4 Bit rate
5 Channel number. For a beacon message, the system locks only to the primary channel. As a result, there is not more than one beacon message. The channel for beacon is 0 (so it matches the DSM 232 family of GPS receivers). For L-band messages, the channel number is 2 (so it matches the DSM 232 family of GPS receivers).
6 Tracking status:
0: Channel idle.
1: Wideband FFT search.
2: Searching for signal.
3: Channel has acquired signal.
4: Channel has locked onto signal. For beacon, this means valid RTCM has been received. For L-band, this means good data has been decoded.
5: Channel disabled.
7 Channel used. Output 1 if the RTCM is being used for outputting DGPS position. 0 otherwise. If the system is not outputting DGPS, the output is 0 also.
8 Channel tracking performance indicator. For beacon this is the word error rate, which is in percentage. For L-band, this is the time since the last sync, in tenths of seconds ranging from 0 through 255.
#############
17. PTNL,GGK
Time, position, position type, DOP
An example of the PTNL,GGK message string is:
$PTNL,GGK,102939.00,051910,5000.97323841,N,00827.62010742,E,5,09,1.9,EHT150.790,M*73
PTNL,GGK message fields
Field Meaning
0 Talker ID $PTNL
1 Message ID GGK
2 UTC time of position fix, in hhmmmss.ss format. Hours must be two numbers, so may be padded. For example, 7 is shown as 07.
3 UTC date of position fix, in ddmmyy format. Day must be two numbers, so may be padded. For example, 8 is shown as 08.
4 Latitude, in degrees and decimal minutes (dddmm.mmmmmmm)
5 Direction of latitude:
N: North
S: South
6 Longitude, in degrees and decimal minutes (dddmm.mmmmmmm). Should contain three digits of ddd.
7 Direction of longitude:
E: East
W: West
8 GPS Quality indicator:
0: Fix not available or invalid
1: Autonomous GPS fix
2: RTK float solution
3: RTK fix solution
4: Differential, code phase only solution (DGPS)
5: SBAS solution – WAAS/EGNOS/MSAS
6: RTK float or RTK location 3D Network solution
7: RTK fixed 3D Network solution
8: RTK float or RTK location 2D in a Network solution
9: RTK fixed 2D Network solution
10: OmniSTAR HP/XP solution
11: OmniSTAR VBS solution
12: Location RTK solution
13: Beacon DGPS
9 Number of satellites in fix
10 Dilution of Precision of fix (DOP)
11 Ellipsoidal height of fix (antenna height above ellipsoid). Must start with EHT.
12 M: ellipsoidal height is measured in meters
13 The checksum data, always begins with *
Note – The PTNL,GGK message is longer than the NMEA-0183 standard of 80 characters.
Note – Even if a user-defined geoid model, or an inclined plane is loaded into the receiver, then the height output in the NMEA GGK string is always an ellipsoid height, for example, EHT24.123.
################
18. PTNL,PJK
Local coordinate position output
Some examples of the PTNL,PJK message string are:
$PTNL,PJK,202831.50,011112,+805083.350,N,+388997.346,E,10,09,1.5,GHT+25.478,M*77
$PTNL,PJK,010717.00,081796,+732646.511,N,+1731051.091,E,1,05,2.7,EHT+28.345,M*7C
PTNL,PJK message fields
Field Meaning
0 Message ID $PTNL,PJK
1 UTC of position fix
2 Date
3 Northing, in meters
4 Direction of Northing will always be N (North)
5 Easting, in meters
6 Direction of Easting will always be E (East)
7 GPS Quality indicator:
0: Fix not available or invalid
1: Autonomous GPS fix
2: RTK float solution
3: RTK fix solution
4: Differential, code phase only solution (DGPS)
5: SBAS solution – WAAS/EGNOS/MSAS
6: RTK Float 3D network solution
7: RTK Fixed 3D network solution
8: RTK Float 2D network solution
9: RTK Fixed 2D network solution
10: OmniSTAR HP/XP solution
11: OmniSTAR VBS solution
12: Location RTK
13: Beacon DGPS
8 Number of satellites in fix
9 DOP of fix
10 Height of Antenna Phase Center (see Note below)
11 M: height is measured in meters
12 The checksum data, always begins with *
Note – The PTNL,PJK message is longer than the NMEA-0183 standard of 80 characters.
Note – If a user-defined geoid model, or an inclined plane is loaded into the receiver, then the NMEA PJK string will always report the orthometric height (the field starts with the letters GHT). If the latitude/longitude of the receiver is outside the user-defined geoid model bounds, then the height is shown as ellipsoidal height (the field starts with the letters EHT).
Note – If the receiver does not have an application file, this string returns nothing in fields 3, 4, 5, 6, or 10.
##################
19. PTNL,PJT
Projection type
An example of the PTNL,PJT message string is:
$PTNL,PJT,NAD83(Conus),California Zone 4 0404,*51
PTNL,PJT message fields
Field Meaning
0 Message ID $PTNL,PJT
1 Coordinate system name (can include multiple words)
2 Project name (can include multiple words)
3 The checksum data, always begins with *
#################
20. PTNL,VGK
Vector information
An example of the PTNL,VGK message string is:
$PTNL,VGK,160159.00,010997,-0000.161,00009.985,-0000.002,3,07,1,4,M*0B
PTNL,VGK message fields
Field Meaning
0 Message ID $PTNL,VGK
1 UTC of vector in hhmmss.ss format
2 Date in mmddyy format
3 East component of vector, in meters
4 North component of vector, in meters
5 Up component of vector, in meters
6 GPS Quality indicator:
0: Fix not available or invalid
1: Autonomous GPS fix
2: RTK float solution
3: RTK fix solution
4: Differential, code phase only solution (DGPS)
5: SBAS solution – WAAS/EGNOS/MSAS
6: RTK Float 3D network solution
7: RTK Fixed 3D network solution
8: RTK Float 2D network solution
9: RTK Fixed 2D network solution
10: OmniSTAR HP/XP solution
11: OmniSTAR VBS solution
12: Location RTK
13: Beacon DGPS
7 Number of satellites if fix solution
8 DOP of fix
9 M: Vector components are in meters
10 The checksum data, always begins with *
#############
21. PTNL,VHD
Heading information
An example of the PTNL,VHD message string is:
$PTNL,VHD,030556.00,093098,187.718,-22.138,-76.929,-5.015,0.033,0.006,3,07,2.4,M*22
PTNL,VHD message fields
Field Meaning
0 Message ID $PTNL,VHD
1 UTC of position in hhmmss.ss format
2 Date in mmddyy format
3 Azimuth
4 Azimuth/Time
5 Vertical Angle
6 Vertical/Time
7 Range
8 Range/Time
9 GPS Quality indicator:
0: Fix not available or invalid
1: Autonomous GPS fix
2: RTK float solution
3: RTK fix solution
4: Differential, code phase only solution (DGPS)
5: SBAS solution – WAAS/EGNOS/MSAS
6: RTK Float 3D network solution
7: RTK Fixed 3D network solution
8: RTK Float 2D network solution
9: RTK Fixed 2D network solution
10: OmniSTAR HP/XP solution
11: OmniSTAR VBS solution
12: Location RTK
13: Beacon DGPS
10 Number of satellites used in solution
11 PDOP
12 The checksum data, always begins with *
################
22. RMC
Position, velocity, and time
The RMC string is:
$GPRMC,123519,A,4807.038,N,01131.000,E,022.4,084.4,230394,003.1,W*6A
GPRMC message fields
Field Meaning
0 Message ID $GPRMC
1 UTC of position fix
2 Status A=active or V=void
3 Latitude
4 Longitude
5 Speed over the ground in knots
6 Track angle in degrees (True)
7 Date
8 Magnetic variation in degrees
9 The checksum data, always begins with *
####################
23. ROT
Rate and direction of turn
An example of the ROT string is:
$GPROT,35.6,A*4E
ROT message fields
Field Meaning
0 Message ID $GPROT
1 Rate of turn, degrees/minutes, “–” indicates bow turns to port
2 A: Valid data
V: Invalid data
3 The checksum data, always begins with *
################
24. VTG
Track made good and speed over ground
An example of the VTG message string is:
$GPVTG,,T,,M,0.00,N,0.00,K*4E
VTG message fields
Field Meaning
0 Message ID $GPVTG
1 Track made good (degrees true)
2 T: track made good is relative to true north
3 Track made good (degrees magnetic)
4 M: track made good is relative to magnetic north
5 Speed, in knots
6 N: speed is measured in knots
7 Speed over ground in kilometers/hour (kph)
8 K: speed over ground is measured in kph
9 The checksum data, always begins with *
################
25. ZDA
UTC day, month, and year, and local time zone offset
An example of the ZDA message string is:
$GPZDA,172809.456,12,07,1996,00,00*45
ZDA message fields
Field Meaning
0 Message ID $GPZDA
1 UTC
2 Day, ranging between 01 and 31
3 Month, ranging between 01 and 12
4 Year
5 Local time zone offset from GMT, ranging from 00 through ±13 hours
6 Local time zone offset from GMT, ranging from 00 through 59 minutes
7 The checksum data, always begins with *
Fields 5 and 6 together yield the total offset. For example, if field 5 is -5 and field 6 is +15, local time is 5 hours and 15 minutes earlier than GMT.
GNSS NMEA-0183 协议相关推荐
- minmea——GPS NMEA 0183 协议解析库
今天给大家推荐一个纯C语言编写,轻量级的GPS NMEA 0183协议解析库:minmea github地址:https://github.com/kosma/minmea 一.特点 1.C99标准编 ...
- 嵌入式GPS模块编程 NMEA协议 0183协议
嵌入式GPS模块编程 NMEA协议 0183协议 学前小知识: NMEA协议是为了在不同的GPS导航设备中建立统一的RTCM(海事无线电技术委员会)标准,它最初是由美国国家海洋电子协会(NMEA-Th ...
- GPS NMEA 0183 4.10协议/GPS Linux串口驱动
NMEA 0183是美国国家海洋电子协会(National Marine Electronics Association)为海用电子设备制定的标准格式.现在已经成为GPS导航设备统一的RTCM(R ...
- GPS NEMA 0183协议
GPS NEMA 0183协议 一. NMEA0183标准语句(GPS常用语句) $GPGGA 例:$GPGGA,092204.999,4250.5589,S,14718.5084,E,1,04,24 ...
- GPS理论知识NMEA 0813协议
18/100发布文章 博文管理我的博客退出 Trash Temp GPS理论知识NMEA 0813协议 添加摘要 18/100发布文章 博文管理我的博客退出 Trash Temp GPS理论知识NME ...
- 看到怒飞垂云的 一节课讲明白所有串口协议-Mavlink/ubx/诺瓦泰/NMEA/自定义协议/变帧长/定帧长 也是很有感触
看到怒飞垂云的 一节课讲明白所有串口协议-Mavlink/ubx/诺瓦泰/NMEA/自定义协议/变帧长/定帧长 也是很有感触 http://www.nufeichuiyun.com/?page_id= ...
- GPS 0183协议GGA、GLL、GSA、GSV、RMC、VTG、ZDA、DTM
NMEA协议是为了在不同的GPS(全球定位系统)导航设备中建立统一的BTCM(海事无线电技术委员会)标准,由美国国家海洋电子协会(NMEA-The National Marine Electronic ...
- GPS 0183协议GGA、GLL、GSA、GSV、RMC、VTG、ZDA、DTM作者：hiphopor
原文地址:GPS 0183协议GGA.GLL.GSA.GSV.RMC.VTG.ZDA.DTM作者:hiphopor 一. NMEA0183标准语句(GPS常用语句) $GPGGA 例:$GPGGA,0 ...
- EC20 4G 模块里GPS 0183协议里有GGA、GLL、GSA、GSV、RMC、VTG，
GPS 0183协议里GGA.GLL.GSA.GSV.RMC.VTG $GPGGA 例: G P G G A , 092204.999 , 4250.5589 , S , 14718.5084 , E ...
- GNSS NMEA ddmm.mmmmm格式转换
ddmm.mmmm(度分)转换成常用坐标dd.ddddd GPS NMEA采集到的经度和纬度格式分别是 纬度ddmm.mmmmm(度分) 经度dddmm.mmmmm(度分) 其中dd是度数,mm.mm ...
最新文章
- 通过Auto Layout深入了解SizeClasses的好处和使用
- beta冲刺（2/7）
- 解决ajax获取不到按钮的id
- 垃圾“程序是怎样练成的”——关于《C程序设计伴侣》第A章（四）
- [armv9]-ARM最新架构为memcpy/memset底层的实现提供新的指令
- js 日期对象 31 号 setMonth 的锅
- matlab符号函数绘图法_转载：MATLAB 符号函数作图
- 【AIX 命令学习】lsattr 显示一个给定设备或一种设备的属性
- java scanner 回车_Java Scanner类用法及nextLine()产生的换行符问题实例分析
- c#程序设计实训报告心得体会_c#学习心得体会范文_c#程序设计心得体会
- 啊哈C语言答案,啊哈c语言开头的题，哪位大佬来试试？
- R语言环境下载及RStudio安装教程
- 电脑使用手机摄像头（超详细）
- 微擎弹出确认授权获取用户头像
- 你可能会读错的字大集合
- [leetcode]Binary Tree Level Order Traversal II
- unity打包报错，又是血压升高的一天
- Racket编程指南——23 Racket和Scheme的方言
- 计算机用户名adm,adm那个电脑设置密码忘记了怎么处理
- 三菱服务器显示51,三菱空调故障代码51什么意思一招解决 -三菱柜机故障代码06...