因此，我最近购买了一台Dell Perc H310 RAID控制器，放入运行Ubuntu Server 18.04.1 LTS的Fujitsu Esprimo P700 E85 +计算机中。主板似乎没有UEFI，只有BIOS。从硬件角度看，我：

将500GB引导驱动器直接连接到MoBo

通过SATA至mini-SAS电缆分配器将2 * 3TB SATA驱动器连接到RAID控制器

在引导配置BIOS中配置了Raid0，RAID1虚拟驱动器

并且在控制器的菜单中一切似乎都很好。

但是当我启动Ubuntu(安装在Boot HDD上)时，找不到6TB，3TB RAID驱动器(分别为RAID0和1)，也没有它组成的2 * 3TB单独驱动器。

I used parted --list and lsblk to check for the drive(s) and lspci to check the controller.

The ouput of lsblk is:

NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT

loop0 7:0 0 87.9M 1 loop /snap/core/5328

loop1 7:1 0 86.6M 1 loop /snap/core/4486

sda 8:0 0 465.8G 0 disk

├─sda1 8:1 0 1M 0 part

└─sda2 8:2 0 465.8G 0 part /

The output of parted --list is:

Model: ATA WDC WD5000AAKX-0 (scsi)

Disk /dev/sda: 500GB

Sector size (logical/physical): 512B/512B

Partition Table: gpt

Disk Flags:

Number Start End Size File system Name Flags

1 1049kB 2097kB 1049kB bios_grub

2 2097kB 500GB 500GB ext4

The output of lspci is:

00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)

00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09)

00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)

00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04)

00:16.2 IDE interface: Intel Corporation 6 Series/C200 Series Chipset Family IDE-r Controller (rev 04)

00:16.3 Serial controller: Intel Corporation 6 Series/C200 Series Chipset Family KT Controller (rev 04)

00:19.0 Ethernet controller: Intel Corporation 82579V Gigabit Network Connection (rev 04)

00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 04)

00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 04)

00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 04)

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a4)

00:1f.0 ISA bridge: Intel Corporation Q65 Express Chipset Family LPC Controller (rev 04)

00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family SATA AHCI Controller (rev 04)

00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 04)

01:00.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS 2008 [Falcon] (rev 03)

And the output of lspci -vv for the RAID controller is:

01:00.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS 2008 [Falcon] (rev 03)

Subsystem: Dell MegaRAID SAS 2008 [Falcon]

Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-

Interrupt: pin A routed to IRQ 16

Region 0: I/O ports at e000 [size=256]

Region 1: Memory at fe460000 (64-bit, non-prefetchable) [size=16K]

Region 3: Memory at fe400000 (64-bit, non-prefetchable) [size=256K]

Expansion ROM at fe440000 [disabled] [size=128K]

Capabilities:

Kernel modules: megaraid_sas

注意：我还在带有UEFI的Windows计算机上尝试了RAID Ctrlr。在我通过PCIe通道B5和B6进行录音之前(我在网上某个地方找到了这个建议)，它没有用卡进行POST。之后，它可以识别RAID0配置。将卡和磁盘移回Ubuntu系统并在那里启动也没有成功。控制器的行为与以前完全相同，这就是为什么我尚未在两条通道上都移除磁带。

我应该如何进行？