fwr310刷openwrt_全网首拆迅捷FWR310 V4.0 300M 路由硬改后刷华硕N14U
昨天16M闪和USB模块存到了。16M闪存已经请店家用编程器刷上了华硕N14U的编程器固件。路由焊上闪存后出现的问题是进不了192.168.1.1页面，指定网关为192.168.1.1可以进去了，显示是固件恢复页面，在这里刷入华硕的固件，显示成功并且路由自动重启，但是还是和前面一样(进不了192.168.1.1页面，指定网关为192.168.1.1可以进去了，显示是固件恢复页面)。TTL显示
U-Boot 1.1.3 (Jan 29 2013 - 15:41:44)
SoC:MediaTek MT7620
DRAM: Memory Testing.65536K OK. is 64 MB
relocate_code Pointer at: 83fac000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: c2 20 18 c2 20 (2018c220)
find flash: MX25L12805D
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
______________________________________________________
| ____ ____ |
| | _ \ _ __ ___ __ _ _ __ ___ | __ ) _____ __ |
| | | | | '__/ _ \/ _` | '_ ` _ \| _ \ / _ \ \/ / |
| | |_| | | | __/ (_| | | | | | | |_) | (_) >
| |____/|_| \___|\__,_|_| |_| |_|____/ \___/_/\_\ |
| |
| DreamBox Team |
| http://www.openwrt.org.cn |
| Board:Mercury MW305R |
| |
| lintel |
|____________________________________________________|
===============System Info==================
ASIC 7620_MP (Port5None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Flash component: SPI Flash
CPU Speed: 580 MHZ
RAM Size:64 Mbytes
Build Date:Jan 29 2013 Time:15:41:44
============================================
GPIO Init:
UARTF_SHARE_MODE:GPIO
I2C_GPIO_MODE:GPIO
GPIO_MODE_REG status:0x1a311d
ReadyLED Bit:0x1
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
0
3: System Boot system code via Flash.
Press Reset button enter upgrade mode!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name:
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 12970108 Bytes = 12.4 MB
Load Address: 80000000
Entry Point: 8000c150
raspi_read: from:50040 len:c5e87c
Verifying Checksum ... OK
Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover
U-Boot 1.1.3 (Jan 29 2013 - 15:41:44)
SoC:MediaTek MT7620
DRAM: Memory Testing.65536K OK. is 64 MB
relocate_code Pointer at: 83fac000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: c2 20 18 c2 20 (2018c220)
find flash: MX25L12805D
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
______________________________________________________
| ____ ____ |
| | _ \ _ __ ___ __ _ _ __ ___ | __ ) _____ __ |
| | | | | '__/ _ \/ _` | '_ ` _ \| _ \ / _ \ \/ / |
| | |_| | | | __/ (_| | | | | | | |_) | (_) >
| |____/|_| \___|\__,_|_| |_| |_|____/ \___/_/\_\ |
| |
| DreamBox Team |
| http://www.openwrt.org.cn |
| Board:Mercury MW305R |
| |
| lintel |
|____________________________________________________|
===============System Info==================
ASIC 7620_MP (Port5None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Flash component: SPI Flash
CPU Speed: 580 MHZ
RAM Size:64 Mbytes
Build Date:Jan 29 2013 Time:15:41:44
============================================
GPIO Init:
UARTF_SHARE_MODE:GPIO
I2C_GPIO_MODE:GPIO
GPIO_MODE_REG status:0x1a311d
ReadyLED Bit:0x1
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
0
3: System Boot system code via Flash.
Press Reset button enter upgrade mode!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name:
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 12970108 Bytes = 12.4 MB
Load Address: 80000000
Entry Point: 8000c150
raspi_read: from:50040 len:c5e87c
Verifying Checksum ... OK
Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover
U-Boot 1.1.3 (Jan 29 2013 - 15:41:44)
SoC:MediaTek MT7620
DRAM: Memory Testing.65536K OK. is 64 MB
relocate_code Pointer at: 83fac000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: c2 20 18 c2 20 (2018c220)
find flash: MX25L12805D
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
______________________________________________________
| ____ ____ |
| | _ \ _ __ ___ __ _ _ __ ___ | __ ) _____ __ |
| | | | | '__/ _ \/ _` | '_ ` _ \| _ \ / _ \ \/ / |
| | |_| | | | __/ (_| | | | | | | |_) | (_) >
| |____/|_| \___|\__,_|_| |_| |_|____/ \___/_/\_\ |
| |
| DreamBox Team |
| http://www.openwrt.org.cn |
| Board:Mercury MW305R |
| |
| lintel |
|____________________________________________________|
===============System Info==================
ASIC 7620_MP (Port5None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Flash component: SPI Flash
CPU Speed: 580 MHZ
RAM Size:64 Mbytes
Build Date:Jan 29 2013 Time:15:41:44
============================================
GPIO Init:
UARTF_SHARE_MODE:GPIO
I2C_GPIO_MODE:GPIO
GPIO_MODE_REG status:0x1a311d
ReadyLED Bit:0x1
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
0
3: System Boot system code via Flash.
Press Reset button enter upgrade mode!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name:
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 12970108 Bytes = 12.4 MB
Load Address: 80000000
Entry Point: 8000c150
raspi_read: from:50040 len:c5e87c
Verifying Checksum ... OK
Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover
U-Boot 1.1.3 (Jan 29 2013 - 15:41:44)
SoC:MediaTek MT7620
DRAM: Memory Testing.65536K OK. is 64 MB
relocate_code Pointer at: 83fac000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: c2 20 18 c2 20 (2018c220)
find flash: MX25L12805D
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
______________________________________________________
| ____ ____ |
| | _ \ _ __ ___ __ _ _ __ ___ | __ ) _____ __ |
| | | | | '__/ _ \/ _` | '_ ` _ \| _ \ / _ \ \/ / |
| | |_| | | | __/ (_| | | | | | | |_) | (_) >
| |____/|_| \___|\__,_|_| |_| |_|____/ \___/_/\_\ |
| |
| DreamBox Team |
| http://www.openwrt.org.cn |
| Board:Mercury MW305R |
| |
| lintel |
|____________________________________________________|
===============System Info==================
ASIC 7620_MP (Port5None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Flash component: SPI Flash
CPU Speed: 580 MHZ
RAM Size:64 Mbytes
Build Date:Jan 29 2013 Time:15:41:44
============================================
GPIO Init:
UARTF_SHARE_MODE:GPIO
I2C_GPIO_MODE:GPIO
GPIO_MODE_REG status:0x1a311d
ReadyLED Bit:0x1
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
0
3: System Boot system code via Flash.
Press Reset button enter upgrade mode!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name:
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 12970108 Bytes = 12.4 MB
Load Address: 80000000
Entry Point: 8000c150
raspi_read: from:50040 len:c5e87c
Verifying Checksum ... OK
Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover
U-Boot 1.1.3 (Jan 29 2013 - 15:41:44)
SoC:MediaTek MT7620
DRAM: Memory Testing.65536K OK. is 64 MB
relocate_code Pointer at: 83fac000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: c2 20 18 c2 20 (2018c220)
find flash: MX25L12805D
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
______________________________________________________
| ____ ____ |
| | _ \ _ __ ___ __ _ _ __ ___ | __ ) _____ __ |
| | | | | '__/ _ \/ _` | '_ ` _ \| _ \ / _ \ \/ / |
| | |_| | | | __/ (_| | | | | | | |_) | (_) >
| |____/|_| \___|\__,_|_| |_| |_|____/ \___/_/\_\ |
| |
| DreamBox Team |
| http://www.openwrt.org.cn |
| Board:Mercury MW305R |
| |
| lintel |
|____________________________________________________|
===============System Info==================
ASIC 7620_MP (Port5None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Flash component: SPI Flash
CPU Speed: 580 MHZ
RAM Size:64 Mbytes
Build Date:Jan 29 2013 Time:15:41:44
============================================
GPIO Init:
UARTF_SHARE_MODE:GPIO
I2C_GPIO_MODE:GPIO
GPIO_MODE_REG status:0x1a311d
ReadyLED Bit:0x1
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
0
3: System Boot system code via Flash.
Press Reset button enter upgrade mode!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name:
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 12970108 Bytes = 12.4 MB
Load Address: 80000000
Entry Point: 8000c150
raspi_read: from:50040 len:c5e87c
fwr310刷openwrt_全网首拆迅捷FWR310 V4.0 300M 路由硬改后刷华硕N14U相关推荐
- 努比亚 Z5 mini刷机包 omni4.4.2改动V4.0 自用版 精简 MIUI特效
ROM介绍: 第一版: 1.基于lwang适配的omni4.4.2第二版改动,少量精简改动 2.设置加入"自启项管理",体验更快.更顺滑 3.替换特效为XUI特效 4.改动host ...
- fwr310刷openwrt_[转载]迅捷FWR310无线路由器的刷机
家里的Linksys WRH54G无线路由应该是2007年购买的,一直使用至今各项功能完好.也算经受住了长年开机的考验.2008年曾在Linksys的官方网站下载过一次Firmware v1.01.0 ...
- 拆 米家台灯_全网首拆：众筹价169元的米家屏幕挂灯拆解评测！柔光罩或成败笔...
眼前在桌面照明界有一种特殊的灯,那就是屏幕挂灯,它可以夹在屏幕上面,减少空间的占用,而且直接照明桌面,甚是方便. 熟悉败家电子产品的朋友肯定了解BenQ明基出过卖一千多元的屏幕挂灯ScreenBar, ...
- 全网首拆乐视S50 Air，内部芯片、裂屏原因曝光
(更新:红字为更新内容,就电容等的技术问题进行了修正.) S50 Air全配版是一台50英寸的.支持偏光式3D的.1080p分辨率电视机,售价 3500元,含2年乐视网会员费980元.带着好奇心,宅客 ...
- fwr310虚拟服务器设置,fast迅捷FWR310无线路由器设置图文教程
这里只介绍家庭常见的PPPoE宽带拨号上网模式设置,也就是需要点宽带连接的亲们.首先需要知道网络运营商提供给您的上网宽带账号和密码,不知道的朋友,请咨询所使用的电信/联通/网通等网络运营商客服获取. ...
- fwr310虚拟服务器设置,Fast迅捷FWR310无线路由器怎么设置
本文介绍了Fast迅捷FWR310无线路由器的安装和ADSL(PPPOE)拨号上网方式的设置方法,ADSL(PPPOE)拨号上网:指的是用户办理宽带业务后,宽带运营商提供了一个宽带用户和密码,在没有用 ...
- 迅捷虚拟服务器的常用服务器,迅捷 FWR310 V1 无线路由器虚拟服务器设置
迅捷 FWR310 V1 无线路由器虚拟服务器设置 2017-03-02 1.确认服务器搭建成功 设置虚拟服务器之前,需要确认以下几点: 2.设置虚拟服务器 登录路由器管理界面,进入"转发规 ...
- 科沃斯扫地机器人拆解_哈士奇拆给你看 篇二：科沃斯T5 Power扫地机器人，首拆！...
哈士奇拆给你看 篇二:科沃斯T5 Power扫地机器人,首拆! 2019-06-14 12:02:25 7点赞 16收藏 9评论 科沃斯T5 Power托扫一体机器人是目前科沃斯主打的旗舰产品,这款产 ...
- mybatis映射longtext类型数据_全网首例全栈实践（五）Spring Boot 集成Mybatis
一.概述 我们的Spring Boot后续项目使用的都是MySQL.Spring Boot连接MySQL的方式包括JDBC,Spring JPA,Hibeirnate,Mybatis等,本文主要带大家 ...
最新文章
- 转_前端开发技术概要
- 大数据开发实战：Hive优化实战2-大表join小表优化
- docker commit 发布自己的镜像
- Razor 也可说是一个asp.net模板引擎，用不着学习 T4 了
- 电脑删除快捷键_可能是知乎最有用的 Windows 快捷键学习指南。
- 今天是 OSChina 上线 6 周年！
- linux基本命令示例_Linux mv命令用法和示例
- 【效率提高10倍项目原创发布！】深度学习数据自动标注器开源 目标检测和图像分类（高精度高效率）
- HENKAKU！PSV（Vita）编程小白探索笔记（一）信息收集篇
- sd卡 linux分区教程,《电脑端SD卡分区 小白教程 支持ext swap 分区无需linux环境、》.docx...
- Sydney 免费wordpress企业主题
- 【转】脸识别技术发展及实用方案设计
- cisco anyConnect 不用每次输入密码的办法
- 为什么更多APP开发者选择穿山甲作为游戏变现平台？
- 文件岛 服务器大陆,重回文件岛《究极数码暴龙》奇遇系统解析
- 什么样的男人才算成熟男人？
- 2023年创新型中小企业评价和专精特新认定
- 关于调用高德地图路径规划清除问题解决方案【js】
- 浪子燕青Dburstnbsp;0.95
- Pycharm及pycharm的terminal运行与CMD运行不一致，出现中文转英文问题（或英文转中文）