#堆叠线缆连接

CE6800-1 40ge 1/0/1 to CE6800-2 40ge 1/0/1

CE6800-1 40ge 1/0/2 to CE6800-2 40ge 1/0/2

#通过CONSOLE口配置CE6800-1的堆叠参数

system-view

#配置堆叠优先级、堆叠ID和域编号。

[~HUAWEI] stack

[~HUAWEI-stack] stack member 1 priority 200

[*HUAWEI-stack] stack member 1 domain 10

[*HUAWEI-stack] quit

[*HUAWEI] commit

#创建堆叠端口。

[~HUAWEI] interface stack-port 1/1

#将堆叠物理成员端口加入堆叠端口。堆叠端口的起止编号需与物理连线一致。

[*HUAWEI-Stack-Port1/1] port member-group interface 40ge 1/0/1 to 1/0/2

[*HUAWEI-Stack-Port1/1] quit

[*HUAWEI] commit

[~HUAWEI] quit

#保存配置脚本。

save

Warning: The current configuration will be written to the device. Continue? [Y/N]:Y

#按Enter键

Info: Please input the file name(*.cfg, *.zip, *.dat)[vrpcfg.zip]:

Now saving the current configuration to the slot 1

Info: Save the configuration successfully.

#重启交换机，耗时约5分钟。

reboot

...

Warning: The system will reboot. Continue? [Y/N]:Y

...

#关闭堆叠接口。

system-view

[~HUAWEI] interface stack-port 1/1

[*HUAWEI-Stack-Port1/1] shutdown

[*HUAWEI-Stack-Port1/1] quit

[*HUAWEI] commit

[~HUAWEI] quit

save

Warning: The current configuration will be written to the device. Continue? [Y/N]:y

...

#通过CONSOLE口配置CE6800-2的堆叠参数

#进入系统视图。

system-view

#配置堆叠ID和堆叠域编号。

[~HUAWEI] stack

[~HUAWEI-stack] stack member 1 renumber 2 inherit-config

Warning: The stack configuration of member ID 1 will be inherited to member ID 2 after the device resets. Continue? [Y/N]:Y

[*HUAWEI-stack] stack member 1 domain 10

Info: The operation takes effect only after the save command is executed. The device with a lower priority then will be reset in stack merging scenario.

[*HUAWEI-stack] quit

[*HUAWEI] commit

#创建堆叠端口。

[~HUAWEI] interface stack-port 1/1

#将堆叠物理成员端口加入堆叠端口。堆叠端口的起止编号需与物理连线一致。

[*HUAWEI-Stack-Port1/1] port member-group interface 40ge 1/0/1 to 1/0/2

[*HUAWEI-Stack-Port1/1] quit

[*HUAWEI] commit

[~HUAWEI] quit

save

Warning: The current configuration will be written to the device. Continue? [Y/N]:Y

#按Enter键

Info: Please input the file name(*.cfg, *.zip, *.dat)[vrpcfg.zip]:

Now saving the current configuration to the slot 1

Info: Save the configuration successfully.

#重启交换机

reboot

...

Warning: The system will reboot. Continue? [Y/N]:Y

...

待CE6800-2启动成功后，登录CE6800-1，执行如下命令。

system-view

[~HUAWEI] interface stack-port 1/1

[*HUAWEI-Stack-Port1/1] undo shutdown

[*HUAWEI-Stack-Port1/1] quit

[*HUAWEI] commit

[~HUAWEI] quit

save

Warning: The current configuration will be written to the device. Continue? [Y/N]:y

...

#验证配置结果

display stack

----------------------------------------------------------------

MemberID Role     MAC              Priority   Device Type

----------------------------------------------------------------

1        Master   30d1-7e72-9650   200        CE6800

2        Standby  30d1-7e72-9600   100        CE6800

----------------------------------------------------------------

display stack topology

Stack Topology:

----------------------------------------------

Stack-Port 1      Stack-Port 2

MemberID   Status Neighbor   Status Neighbor

----------------------------------------------

1          up     2          --     --

2          up     1          --     --

----------------------------------------------

Stack Link:

----------------------------------------------------------------------------

Stack-Port       Port               Status     PeerPort           PeerStatus

----------------------------------------------------------------------------

Stack-Port1/1    40GE1/0/1          up         40GE2/0/1          up

Stack-Port1/1    40GE1/0/2          up         40GE2/0/2          up

Stack-Port2/1    40GE2/0/1          up         40GE1/0/1          up

Stack-Port2/1    40GE2/0/2          up         40GE1/0/2          up

----------------------------------------------------------------------------

继续阅读：华为  交换机

原创文章请注明转载自技术小站本文地址：http://www.i5i6.net/post/219.html，标题：华为CE6800交换机堆叠配置