avaya基本配置方法

ctrl+e
用户名：dadmin
密码：jrj123
pin:jrj1234
4410

查看开长途没有
cha sta 8328 8328
cor 1 不能打 2 能打长途

查看掩饰号码
cha pub 0/1/2

查看出局：
cha pub 4 ext 分机
F3保存

查看入局
cha inc tru 1/2（分别2个组）

4600 IVR组

save t 保存

山东AVAYA设备
172.29.10.170
dadmin
dadmin01
sat
dadmin01
w2ktt

测试通道
status trunk 1
跟踪分机状态
list trace station 4427
查看板卡信息
list configuration stations
查看板卡状态
list cor
查看异地出具的归属
cha station ****
更改cor以后就可以异地出局
test bo 1a08
test bo 1a09
test bo 1a10
test bo 1a11ch
查看板卡组状态
st sig 3
st sig 4
st sig 5
st sig 6

status aesvcs link 检查aes连接情况

list hunt-group 查看ivr组
change inc-call-handling-trmt trunk-group 4 更改呼入ivr组指向

list configuration carrier 板卡号查看板卡配置信息
list configuration all 查看所有板卡配置
status media-processor all 查看所有media板卡
status media-processor board 7a13 查看板卡信息
test board 7a13 测试板卡状态
display errors 查看错误
display alarms 查看告警
list ipserver-interface 查看ip卡
list ip-interface all 查看c-lan板卡，media-pro板卡
list public-unknown-numbering 查看出局号
change public-unknown-numbering ext-digits 8402 0 更改出局号
monitor traffic trunk-groups 查看满线路情况
display sys cu 查看系统license
status trunk x 查看中继x各端口的状态

disp feature-access 查看外拨出局总号
disp dialplan analysis 查看外拨出局

display inc-call-handling-trmt trunk-group 4 查看入局落入分机组
cha inc-call-handling-trmt trunk-group 修改落入分机组，修改直拨电话使用

dup sta 3801 start 3701 board 03a07 count 100 批量添加100个分机在某一个分机板上
list sta 5771 count 10 查看从5771开始的10个分机

cha cor 11查看time of day chart
list partition-route-table查看路由表
list route-pattern 查看路由trunk表

配置ipsi卡
前提G650安装完毕加电
IPSI板卡插到G650网关的第一个槽位（支持热插拔）
笔记本连接到IPSI板卡前端的Service口（固定IP地址192.11.13.6）
Windows界面点击开始菜单-运行-cmd进入dos
ping 192.11.13.6如果可以ping通
telnet 192.11.13.6 回车
[IPSI]: ipsilogin
Login: craft
Password: serv1ces
[IPADMIN]: set control interface 198.152.254.203 255.255.255.0
[IPADMIN]: show control interface
[IPADMIN]: exit
telnet 192.11.13.6 回车
[IPSI]: ipsilogin
Login: craft
Password: serv1ces
[IPADMIN]: set control gateway 198.152.254.1
[IPADMIN]: show control gateway
[IPADMIN]: exit
添加cabinet
add cabinet *
Cabinet Layout:G650-rack-mount-stack

change system-parameters ipserver-interface允许IPSI控制端口网络
IPSI Control of Port Networks: enabled

add ipserver-interface PNnumber

List ipserver-interface查看IPSI注册状态

change system-parameters maintenance修改系统维护参数

change node-names ip
添加media板卡地址和名称
change circuit-packs *查看设备识别情况

音频流压缩
cha ip-network-region 1
==================================================================================
IP NETWORK REGION
Region: 1
Location: 1 Authoritative Domain:
Name: Main
MEDIA PARAMETERS Intra-region IP-IP Direct Audio: yes
Codec Set: 1 Inter-region IP-IP Direct Audio: yes
UDP Port Min: 2048 IP Audio Hairpinning? n
UDP Port Max: 65535
DIFFSERV/TOS PARAMETERS RTCP Reporting Enabled? y
Call Control PHB Value: 46 RTCP MONITOR SERVER PARAMETERS
Audio PHB Value: 46 Use Default Server Parameters? y
Video PHB Value: 26
802.1P/Q PARAMETERS
Call Control 802.1p Priority: 6
Audio 802.1p Priority: 6
Video 802.1p Priority: 5 AUDIO RESOURCE RESERVATION PARAMETERS
H.323 IP ENDPOINTS RSVP Enabled? n
H.323 Link Bounce Recovery? y
Idle Traffic Interval (sec): 20
Keep-Alive Interval (sec): 5
Keep-Alive Count: 5
=======================================================================================
cha ip-codec-set 1
=======================================================================================
IP Codec Set

Codec Set: 1

Audio Silence Frames Packet
Codec Suppression Per Pkt Size(ms)
1: G.729 n 2 20
2:
3:
4:
5:
6:
7:

Media Encryption
1: none
2:
3:
========================================================================================

配置trunk
1. 接入中继线
2. 添加中继板卡
add ds1 *******
name:*****
bit rate:2.048
line coding:hdb3
signaling mode:isdn-pri
country protocol:18
interface companding:alaw
idle code:01010110

3. test bo 中继板卡号，检查通畅情况(busyout 中继板卡号，release 中继板卡号)
4. add signal-group **
==================================================================================
SIGNALING GROUP

Group Number: 4 Group Type: isdn-pri
Associated Signaling? y Max number of NCA TSC: 0
Primary D-Channel: 01A1316 Max number of CA TSC: 0
Trunk Group for NCA TSC:
Trunk Group for Channel Selection:
TSC Supplementary Service Protocol: a Network Call Transfer? n
==================================================================================
5. cha trunk **，添加中继板卡号
6. status trunk **，查看trunk状态

配置IPtrunk
1. 接入clan板卡
add ip-interface 1a05
========add ip-interface 1a05=========================================================
IP INTERFACES

Type: C-LAN
Slot: 01A05
Code/Suffix: TN799 D
Node Name: clan(a05)
IP Address: 172.29 .10 .175
Subnet Mask: 255.255.255.0 Link: 1
Gateway Address: 172.29 .10 .1
Enable Ethernet Port? y Allow H.323 Endpoints? y
Network Region: 1 Allow H.248 Gateways? y
VLAN: n Gatekeeper Priority: 5

Target socket load and Warning level: 400
Receive Buffer TCP Window Size: 8320
ETHERNET OPTIONS
Auto? n
Speed: 100Mbps
Duplex: Full
========================================================================================

2. 添加数据模块
add data-module 3100
========add data-module 3100============================================================
DATA MODULE

Data Extension: 3100 Name: TO AES_1
Type: ethernet
Port: 01A0517
Link: 1

Network uses 1's for Broadcast Addresses? y
========================================================================================

3. 添加signal-group
add signal-group 7
========add signal-group 7==============================================================
SIGNALING GROUP

Group Number: 7 Group Type: h.323
Remote Office? n Max number of NCA TSC: 0
SBS? n Max number of CA TSC: 0
IP Video? n Trunk Group for NCA TSC:
Trunk Group for Channel Selection: 14
TSC Supplementary Service Protocol: a Network Call Transfer? n
T303 Timer(sec): 10

Near-end Node Name: clan(a05) Far-end Node Name: RemoteClan
Near-end Listen Port: 6510 Far-end Listen Port: 6510
Far-end Network Region: 1
LRQ Required? n Calls Share IP Signaling Connection? y
RRQ Required? n
Bypass If IP Threshold Exceeded? n
H.235 Annex H Required? n
DTMF over IP: out-of-band Direct IP-IP Audio Connections? y
Link Loss Delay Timer(sec): 90 IP Audio Hairpinning? n
Enable Layer 3 Test? y Interworking Message: PROGress
DCP/Analog Bearer Capability: 3.1kHz
========================================================================================
busy signaling-gr 7
rel signaling-gr 7

4. 添加ip-codec-set
===add ip-codec-set 1 ===================================================================
IP Codec Set

Codec Set: 1

Audio Silence Frames Packet
Codec Suppression Per Pkt Size(ms)
1: G.729 n 2 20
2:
3:
4:
5:
6:
7:
=========================================================================================

5. 添加trunk
===add trunk 14==========================================================================
TRUNK GROUP

Group Number: 14 Group Type: isdn CDR Reports: y
Group Name: To_150_YiDong COR: 1 TN: 1 TAC: 714
Direction: two-way Outgoing Display? n Carrier Medium: H.323
Dial Access? n Busy Threshold: 255 Night Service:
Queue Length: 0
Service Type: tie Auth Code? n
Member Assignment Method: auto
Signaling Group: 7
Number of Members: 30

Group Type: isdn

TRUNK PARAMETERS
Codeset to Send Display: 6 Codeset to Send National IEs: 6
Charge Advice: none
Supplementary Service Protocol: a Digit Handling (in/out): enbloc/enbloc

Digital Loss Group: 18
Incoming Calling Number - Delete: Insert: Format:

Disconnect Supervision - In? y Out? y
Answer Supervision Timeout: 0

TRUNK FEATURES
ACA Assignment? n Measured: both
Internal Alert? n Maintenance Tests? y
Data Restriction? n NCA-TSC Trunk Member:
Send Name: n Send Calling Number: y
Used for DCS? n Send EMU Visitor CPN? n
Suppress # Outpulsing? n Format: public
UUI IE Treatment: service-provider

Replace Restricted Numbers? n
Replace Unavailable Numbers? n
Send Connected Number: n
Network Call Redirection: none Hold/Unhold Notifications? n
Send UUI IE? y Modify Tandem Calling Number? n
Send UCID? n
Send Codeset 6/7 LAI IE? y
==========================================================================================

重置分机
busyou station ****
release station ****

配置分机内呼
cha aar an

不同pbx之间分机转呼
cha uniform-dial 0
cha aar an

设置分机之间的监听
cha cor *
修改cor：
Can Be Service Observed?是否被监听
Can Be A Service Observer?是否监听
修改监听码：
cha feature-access-codes

change system-parameters features
修改：
service obsevring：warning tone打成n

ip-trunk如果不输送主叫号码，cha trunk 1中的 Send Calling Number: n没有设置成y

====================命令解锁================================
1. 查看在线用户
status logins
2. reset log **

==========================================================
内部分机互通

cha aar an

Dialed Total Route Call Node
String Min Max Pattern Type Number

186 11 11 p2 aar
188 11 11 p2 aar
189 11 11 p2 aar
3200 4 4 9 aar
59 4 4 100 aar
61 4 4 100 aar
65 4 4 20 aar
77 4 4 100 aar
82 4 4 20 aar
841 4 4 20 aar
842 4 4 20 aar
843 4 4 20 aar
=====================================================================
list uniform-dialplan Page

UNIFORM DIAL PLAN TABLE

Matching Pattern Len Del Insert Digits Net Conv Node Num

3200 4 0 aar n
59 4 0 aar n
61 4 0 aar n
65 4 0 aar n
77 4 0 aar n
82 4 0 aar n
841 4 0 aar n
842 4 0 aar n
843 4 0 aar n
844 4 0 aar n
845 4 0 aar n
846 4 0 aar n
847 4 0 aar n
8480 4 0 aar n
8481 4 0 aar n

查看电话统计信息
list bcms trunk 6 day

添加mediapro板卡

F1退出，F3保存

avaya基本配置方法相关推荐

各型号交换机端口镜像配置方法和命令
各型号交换机端口镜像配置方法和命令 "Port Mirror"即端口镜像,端口镜像为网络传输提供了备份通道.此外,还可以用于进行数据流量监测.可以这样理解:在端口A和端口B之间建立 ...
Linux下环境变量配置方法梳理（.bash_profile和.bashrc的区别）
博客园首页新随笔联系管理订阅 <div class="blogStats"> 随笔- 556 文章- 38 评论- 77 ...
TVM darknet yolov3算子优化与量化代码的配置方法
TVM darknet yolov3算子优化与量化代码的配置方法使用以下接口函数  tvm.relay.optimize  quantize.quantize 实际代码: convert nnv ...
Lumen框架多数据库连接配置方法
Lumen作为一款API导向很浓的框架,配置极简化,默认只支持一路DB配置然而随着业务复杂度的提高,引入多个数据库连接似乎无法避免,下面介绍一下LUMEN连接多个数据库的配置方法: 修改.env文件 ...
mysql数据库解压安装教程_MySQL数据库之windows 10下解压版MySql安装配置方法教程...
本文主要向大家介绍了MySQL数据库之windows 10下解压版MySql安装配置方法教程 ,通过具体的内容向大家展现,希望对大家学习MySQL数据库有所帮助. windows 10 下安装解压版的 ...
python3.6.2怎样安装,python 3.6.2 安装配置方法图文教程
python 3.6.2 安装配置方法图文教程 Windows下Python(pip)环境搭建(3.6)图解,供大家参考,具体内容如下 1.下载最新的Python安装:3.6.2 2.安装时不要选择默 ...
.net下的富文本编辑器FCKeditor的配置方法（图）原创
.net下的富文本编辑器FCKeditor的配置方法(图)原创 FCKeditor是一款开源的富文本编辑器,几乎支持所有流行的Web开发语言,版本稳定,用户多,可配置性好. 以前做Java和php的时 ...
php symfony 安装,Symfony的安装和配置方法
这篇文章主要介绍了Symfony的安装和配置方法,分析了使用Composer安装Symfony的具体步骤与相关技巧,需要的朋友可以参考下本文实例讲述了Symfony的安装和配置方法.分享给大家供大家 ...
Win2008远程多用户登陆的配置方法
核心提示:在使用Windows 2008远程登录功能时,如果需要进行多用户登录,可以采用以下配置方法在使用Windows 2008远程登录功能时,如果需要进行多用户登录,可以采用以下配置方法: 首先 ...

avaya基本配置方法

avaya基本配置方法相关推荐

最新文章

热门文章