本帖最后由 qq253044370 于 2019-1-13 23:34 编辑

刷的L大的。自己编译的。极路由B70

本来一直好好的。就是重启了一下路由，就搜不到wifi了。无线是开着的。删除掉重新添加。也不行。

然后甚至按照网上的方法 读取eeprom.bin 里面也能看到mac地址。和别人提供的B70eeprom对比了一下。mac地址并不是FF。

然后进breed里看 mac地址也都对。

但是就是搜不到wifi。有线可以正常用。

内核日志  有个这个错误mt7603e 0000:01:00.0: MCU message 8 (seq 8) timed out 这不是驱动没有加载？？

[    0.000000] Linux version 4.14.91 (ricky@DESKTOP-IKOQ856) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r1148-c466387e)) #0 SMP Fri Jan 11 04:23:52 2019

[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3

[    0.000000] bootconsole [early0] enabled

[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)

[    0.000000] MIPS: machine is HiWiFi HC5962

[    0.000000] Determined physical RAM map:

[    0.000000]  memory: 10000000 @ 00000000 (usable)

[    0.000000] Initrd not found or empty - disabling initrd

[    0.000000] VPE topology {2,2} total 4

[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.

[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes

[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.

[    0.000000] Zone ranges:

[    0.000000]   Normal   [mem 0x0000000000000000-0x000000000fffffff]

[    0.000000]   HighMem  empty

[    0.000000] Movable zone start for each node

[    0.000000] Early memory node ranges

[    0.000000]   node   0: [mem 0x0000000000000000-0x000000000fffffff]

[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]

[    0.000000] On node 0 totalpages: 65536

[    0.000000] free_area_init_node: node 0, pgdat 805aa080, node_mem_map 81003000

[    0.000000]   Normal zone: 512 pages used for memmap

[    0.000000]   Normal zone: 0 pages reserved

[    0.000000]   Normal zone: 65536 pages, LIFO batch:15

[    0.000000] random: get_random_bytes called from start_kernel+0x90/0x4a4 with crng_init=0

[    0.000000] percpu: Embedded 14 pages/cpu @81210000 s26704 r8192 d22448 u57344

[    0.000000] pcpu-alloc: s26704 r8192 d22448 u57344 alloc=14*4096

[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3

[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 65024

[    0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2

[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)

[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)

[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)

[    0.000000] Writing ErrCtl register=00005b30

[    0.000000] Readback ErrCtl register=00005b30

[    0.000000] Memory: 253236K/262144K available (4560K kernel code, 231K rwdata, 1008K rodata, 268K init, 248K bss, 8908K reserved, 0K cma-reserved, 0K highmem)

[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1

[    0.000000] Hierarchical RCU implementation.

[    0.000000] NR_IRQS: 256

[    0.000000] CPU Clock: 880MHz

[    0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns

[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns

[    0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns

[    0.007805] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)

[    0.073976] pid_max: default: 32768 minimum: 301

[    0.078744] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)

[    0.085253] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)

[    0.094023] Hierarchical SRCU implementation.

[    0.099166] smp: Bringing up secondary CPUs ...

[    9.134811] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.

[    9.134820] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes

[    9.134832] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.

[    9.134968] CPU1 revision is: 0001992f (MIPS 1004Kc)

[    0.163910] Synchronize counters for CPU 1: done.

[    9.165748] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.

[    9.165756] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes

[    9.165766] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.

[    9.165839] CPU2 revision is: 0001992f (MIPS 1004Kc)

[    0.255004] Synchronize counters for CPU 2: done.

[    9.255043] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.

[    9.255050] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes

[    9.255059] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.

[    9.255140] CPU3 revision is: 0001992f (MIPS 1004Kc)

[    0.340181] Synchronize counters for CPU 3: done.

[    0.370042] smp: Brought up 1 node, 4 CPUs

[    0.377813] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns

[    0.387597] futex hash table entries: 1024 (order: 3, 32768 bytes)

[    0.393892] pinctrl core: initialized pinctrl subsystem

[    0.400474] NET: Registered protocol family 16

[    0.414291] FPU Affinity set after 11720 emulations

[    0.415774] pull PCIe RST: RALINK_RSTCTRL = 0

[    0.720429] release PCIe RST: RALINK_RSTCTRL = 7000000

[    0.725478] ***** Xtal 40MHz *****

[    0.728832] release PCIe RST: RALINK_RSTCTRL = 7000000

[    0.733930] Port 0 N_FTS = 1b105000

[    0.737397] Port 1 N_FTS = 1b105000

[    0.740843] Port 2 N_FTS = 1b102800

[    1.895843] PCIE2 no card, disable it(RST&CLK)

[    1.900204]  -> 21007f2

[    1.902610] PCIE0 enabled

[    1.905199] PCIE1 enabled

[    1.907803] PCI host bridge /pcie@1e140000 ranges:

[    1.912577]  MEM 0x0000000060000000..0x000000006fffffff

[    1.917732]   IO 0x000000001e160000..0x000000001e16ffff

[    1.922936] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000

[    1.938507] mt7621_gpio 1e000600.gpio: registering 32 gpios

[    1.944322] mt7621_gpio 1e000600.gpio: registering 32 gpios

[    1.950010] mt7621_gpio 1e000600.gpio: registering 32 gpios

[    1.957053] PCI host bridge to bus 0000:00

[    1.961077] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]

[    1.967937] pci_bus 0000:00: root bus resource [io  0xffffffff]

[    1.973768] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]

[    1.980524] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]

[    1.988416] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400

[    1.988455] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]

[    1.988468] pci 0000:00:00.0: reg 0x14: [mem 0x60300000-0x6030ffff]

[    1.988529] pci 0000:00:00.0: supports D1

[    1.988538] pci 0000:00:00.0: PME# supported from D0 D1 D3hot

[    1.988756] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400

[    1.988782] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]

[    1.988795] pci 0000:00:01.0: reg 0x14: [mem 0x60310000-0x6031ffff]

[    1.988845] pci 0000:00:01.0: supports D1

[    1.988853] pci 0000:00:01.0: PME# supported from D0 D1 D3hot

[    1.989221] pci 0000:01:00.0: [14c3:7603] type 00 class 0x028000

[    1.989263] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff]

[    1.989388] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold

[    1.989567] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01

[    1.989741] pci 0000:02:00.0: [14c3:7662] type 00 class 0x028000

[    1.989791] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]

[    1.989836] pci 0000:02:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]

[    1.989926] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold

[    1.990103] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02

[    1.990120] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 02

[    1.990176] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]

[    1.996719] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]

[    2.003599] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]

[    2.010190] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]

[    2.017085] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]

[    2.023833] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]

[    2.030554] pci 0000:00:01.0: BAR 9: assigned [mem 0x60200000-0x602fffff pref]

[    2.037743] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]

[    2.044477] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]

[    2.051235] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]

[    2.057949] pci 0000:00:00.0: PCI bridge to [bus 01]

[    2.062892] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]

[    2.069621] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit]

[    2.076893] pci 0000:02:00.0: BAR 6: assigned [mem 0x60200000-0x6020ffff pref]

[    2.084034] pci 0000:00:01.0: PCI bridge to [bus 02]

[    2.088978] pci 0000:00:01.0:   bridge window [mem 0x60100000-0x601fffff]

[    2.095704] pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff pref]

[    2.104180] clocksource: Switched to clocksource GIC

[    2.110387] NET: Registered protocol family 2

[    2.115456] TCP established hash table entries: 2048 (order: 1, 8192 bytes)

[    2.122342] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)

[    2.128785] TCP: Hash tables configured (established 2048 bind 2048)

[    2.135195] UDP hash table entries: 256 (order: 1, 8192 bytes)

[    2.140963] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)

[    2.147446] NET: Registered protocol family 1

[    2.151763] PCI: CLS 0 bytes, default 32

[    2.384137] 4 CPUs re-calibrate udelay(lpj = 2924544)

[    2.390342] Crashlog allocated RAM at address 0x3f00000

[    2.395733] workingset: timestamp_bits=30 max_order=16 bucket_order=0

[    2.407908] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[    2.413649] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.

[    2.425927] random: fast init done

[    2.429970] io scheduler noop registered

[    2.433795] io scheduler deadline registered (default)

[    2.439778] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled

[    2.447333] console [ttyS0] disabled

[    2.450869] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 18, base_baud = 3125000) is a 16550A

[    2.459910] console [ttyS0] enabled

[    2.466819] bootconsole [early0] disabled

[    2.475526] cacheinfo: Unable to detect cache hierarchy for CPU 0

[    2.482221] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error

[    2.489348] Enable NFI Clock

[    2.492219] # MTK NAND # : Use HW ECC

[    2.495921] Device found in MTK table, ID: c8d1, EXT_ID: 809540

[    2.501818] Support this Device in MTK table! c8d1

[    2.506789] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16

[    2.513245] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xd1

[    2.519581] nand: ESMT NAND 128MiB 3,3V 8-bit

[    2.523919] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64

[    2.531479] Scanning device for bad blocks

[    2.678201] 12 fixed-partitions partitions found on MTD device MT7621-NAND

[    2.685056] Creating 12 MTD partitions on "MT7621-NAND":

[    2.690350] 0x000000000000-0x000000080000 : "u-boot"

[    2.696235] 0x000000080000-0x000000100000 : "debug"

[    2.701945] 0x000000100000-0x000000140000 : "factory"

[    2.707863] 0x000000140000-0x000000340000 : "kernel"

[    2.713612] 0x000000340000-0x000002140000 : "ubi"

[    2.719388] 0x000002140000-0x0000021c0000 : "hw_panic"

[    2.725370] 0x0000021c0000-0x000002240000 : "bdinfo"

[    2.731134] 0x000002240000-0x0000022c0000 : "backup"

[    2.736977] 0x0000022c0000-0x0000032c0000 : "overly"

[    2.742835] 0x0000032c0000-0x0000052c0000 : "firmware_backup"

[    2.749702] 0x0000052c0000-0x0000054c0000 : "oem"

[    2.755290] 0x0000054c0000-0x000007f80000 : "opt"

[    2.761145] [mtk_nand] probe successfully!

[    2.765972] Signature matched and data read!

[    2.770220] load_fact_bbt success 1023

[    2.774623] libphy: Fixed MDIO Bus: probed

[    2.845959] mtk_soc_eth 1e100000.ethernet: generated random MAC address 46:fd:09:90:14:23

[    2.854310] libphy: mdio: probed

[    4.257078] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver

[    4.263624] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 20

[    4.273945] NET: Registered protocol family 10

[    4.279719] Segment Routing with IPv6

[    4.283450] NET: Registered protocol family 17

[    4.287960] 8021q: 802.1Q VLAN Support v1.8

[    4.294973] UBI: auto-attach mtd4

[    4.298298] ubi0: attaching mtd4

[    4.579544] ubi0: scanning is finished

[    4.598381] ubi0: attached mtd4 (name "ubi", size 30 MiB)

[    4.603768] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes

[    4.610628] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048

[    4.617397] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096

[    4.624338] ubi0: good PEBs: 240, bad PEBs: 0, corrupted PEBs: 0

[    4.630314] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128

[    4.637515] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1084714366

[    4.646616] ubi0: available PEBs: 0, total reserved PEBs: 240, PEBs reserved for bad PEB handling: 20

[    4.655824] ubi0: background thread "ubi_bgt0d" started, PID 377

[    4.657474] block ubiblock0_0: created from ubi0:0(rootfs)

[    4.667291] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem

[    4.674248] hctosys: unable to open rtc device (rtc0)

[    4.686866] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.

[    4.694711] Freeing unused kernel memory: 268K

[    4.699150] This architecture does not have kernel memory protection.

[    5.177115] init: Console is alive

[    5.180743] init: - watchdog -

[    5.205414] mtk_soc_eth 1e100000.ethernet eth0: port 4 link up

[    5.898618] mtk_soc_eth 1e100000.ethernet eth0: port 1 link up

[    6.071704] kmodloader: loading kernel modules from /etc/modules-boot.d/*

[    6.124805] usbcore: registered new interface driver usbfs

[    6.130355] usbcore: registered new interface driver hub

[    6.135812] usbcore: registered new device driver usb

[    6.150583] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, using dummy regulator

[    6.159331] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator

[    6.168264] xhci-mtk 1e1c0000.xhci: xHCI Host Controller

[    6.173602] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1

[    6.184327] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010

[    6.193495] xhci-mtk 1e1c0000.xhci: irq 19, io mem 0x1e1c0000

[    6.200201] hub 1-0:1.0: USB hub found

[    6.204021] hub 1-0:1.0: 2 ports detected

[    6.208611] xhci-mtk 1e1c0000.xhci: xHCI Host Controller

[    6.213918] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2

[    6.221424] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0  SuperSpeed

[    6.228027] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.

[    6.236949] hub 2-0:1.0: USB hub found

[    6.240757] hub 2-0:1.0: 1 port detected

[    6.247301] kmodloader: done loading kernel modules from /etc/modules-boot.d/*

[    6.264501] init: - preinit -

[    7.336770] mtk_soc_eth 1e100000.ethernet: PPE started

[    7.415928] random: procd: uninitialized urandom read (4 bytes read)

[   10.515799] mount_root: loading kmods from internal overlay

[   10.549839] kmodloader: loading kernel modules from //etc/modules-boot.d/*

[   10.564758] kmodloader: done loading kernel modules from //etc/modules-boot.d/*

[   10.910407] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 477

[   10.983810] UBIFS (ubi0:1): recovery needed

[   11.179574] UBIFS (ubi0:1): recovery completed

[   11.184203] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"

[   11.192000] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes

[   11.201895] UBIFS (ubi0:1): FS size: 7110656 bytes (6 MiB, 56 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)

[   11.211950] UBIFS (ubi0:1): reserved for root: 335853 bytes (327 KiB)

[   11.218378] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID F3DD9FD9-9766-49A8-B4F4-AE1CDF717759, small LPT model

[   11.232366] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab

[   11.248839] block: extroot: not configured

[   11.294415] UBIFS (ubi0:1): un-mount UBI device 0

[   11.299127] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops

[   11.311085] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 480

[   11.450357] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"

[   11.458204] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes

[   11.468086] UBIFS (ubi0:1): FS size: 7110656 bytes (6 MiB, 56 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)

[   11.478137] UBIFS (ubi0:1): reserved for root: 335853 bytes (327 KiB)

[   11.484564] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID F3DD9FD9-9766-49A8-B4F4-AE1CDF717759, small LPT model

[   11.502745] mount_root: loading kmods from internal overlay

[   11.534331] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*

[   11.558871] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*

[   11.794093] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab

[   11.805846] block: extroot: not configured

[   11.846935] mount_root: switching to ubifs overlay

[   11.887985] urandom-seed: Seeding with /etc/urandom.seed

[   11.986912] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818

[   12.005405] procd: - early -

[   12.008384] procd: - watchdog -

[   12.674358] procd: - watchdog -

[   12.677797] procd: - ubus -

[   12.770253] random: ubusd: uninitialized urandom read (4 bytes read)

[   12.874973] random: ubusd: uninitialized urandom read (4 bytes read)

[   12.881790] random: ubusd: uninitialized urandom read (4 bytes read)

[   12.889069] procd: - init -

[   13.477479] kmodloader: loading kernel modules from /etc/modules.d/*

[   13.516228] gre: GRE over IPv4 demultiplexor driver

[   13.522989] ip_gre: GRE over IPv4 tunneling driver

[   13.535599] ip6_tables: (C) 2000-2006 Netfilter Core Team

[   13.548527] Netfilter messages via NETLINK v0.30.

[   13.555265] ip_set: protocol 6

[   13.595646] u32 classifier

[   13.598369]     input device check on

[   13.602013]     Actions configured

[   13.607622] Mirror/redirect action on

[   13.623245] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)

[   13.637225] Loading modules backported from Linux version v4.19.7-0-g61c68f2a2af0

[   13.644767] Backport generated by backports.git v4.19.7-1-0-g148b072d

[   13.654770] ip_tables: (C) 2000-2006 Netfilter Core Team

[   13.707795] ctnetlink v0.93: registering with nfnetlink.

[   13.786832] usbcore: registered new interface driver usblp

[   13.799864] wireguard: WireGuard 0.0.20181218 loaded. See www.wireguard.com for information.

[   13.808403] wireguard: Copyright (C) 2015-2018 Jason A. Donenfeld . All Rights Reserved.

[   13.854765] xt_time: kernel timezone is -0000

[   13.936076] bus=0x1, slot = 0x0, irq=0xff

[   13.940329] mt7603e 0000:01:00.0: ASIC revision: 76030010

[   13.980756] mt7603e 0000:01:00.0: Firmware Version: 1

[   13.985995] mt7603e 0000:01:00.0: Build Time: 20161027164355

[   14.024289] mt7603e 0000:01:00.0: firmware init done

[   14.204984] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'

[   14.222563] bus=0x2, slot = 0x1, irq=0xff

[   14.226922] mt76x2e 0000:02:00.0: ASIC revision: 76120044

[   14.885074] mt76x2e 0000:02:00.0: ROM patch build: 20141115060606a

[   14.895767] mt76x2e 0000:02:00.0: Firmware Version: 0.0.00

[   14.901269] mt76x2e 0000:02:00.0: Build: 1

[   14.905378] mt76x2e 0000:02:00.0: Build Time: 201507311614____

[   14.934347] mt76x2e 0000:02:00.0: Firmware running!

[   14.942083] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'

[   14.955104] PPP generic driver version 2.4.2

[   14.961216] PPP MPPE Compression module registered

[   14.967684] NET: Registered protocol family 24

[   14.975329] kmodloader: done loading kernel modules from /etc/modules.d/*

[   15.688169] urandom_read: 5 callbacks suppressed

[   15.688181] random: jshn: uninitialized urandom read (4 bytes read)

[   17.422199] xt_FULLCONENAT: RFC3489 Full Cone NAT module

[   17.422199] xt_FULLCONENAT: Copyright (C) 2018 Chion Tang

[   17.983053] random: crng init done

[   25.701345] mtk_soc_eth 1e100000.ethernet: PPE started

[   25.712878] device eth0 entered promiscuous mode

[   25.721582] br-lan: port 1(eth0.1) entered blocking state

[   25.727082] br-lan: port 1(eth0.1) entered disabled state

[   25.733180] device eth0.1 entered promiscuous mode

[   25.741148] br-lan: port 1(eth0.1) entered blocking state

[   25.746589] br-lan: port 1(eth0.1) entered forwarding state

[   25.753017] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready

[   26.715262] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready

[   31.674194] mt7603e 0000:01:00.0: MCU message 8 (seq 8) timed out

[   31.694438] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready

[   31.706304] br-lan: port 2(wlan0) entered blocking state

[   31.711659] br-lan: port 2(wlan0) entered disabled state

[   31.717601] device wlan0 entered promiscuous mode

[   35.274192] mt7603e 0000:01:00.0: MCU message 8 (seq 9) timed out

[   35.294443] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready

[   35.301065] br-lan: port 2(wlan0) entered blocking state

[   35.306411] br-lan: port 2(wlan0) entered forwarding state