各种骚操作试试 V7变回V5试试，直接变胖FAT，刷。。。2020-10-26
本文稿原创，未经许可授权，不得转载！！！！
机器买回来还是很兴奋的。。。
查资料，看说明，学技术。。。。终于！从廋变成胖的了。。。。兴奋！
买了二个，一个胖一个廋，两全了，接入AC，配置，一开始不成功，之后成功了。。。。。兴奋！！
这会的信息有点爆棚，有点高了，不知所以了。。。。想各种骚操作试试 V7变回V5试试，直接变胖FAT，刷。。。兴奋！！！
刷得还是很爽，挺兴奋的！！！！！
先是SDRAM and RUN ，成功了。。。。重启。。。。。成功！！！爽！！！
【wa4320h-acn】DIR
..........................................................
什么也没有！！！????.............
预感不好。。。。。。。
没办法， reboot.....不行，。。。。。。没有文件（后来才知道是flash：没有了）
reset ctrl+B.............. tftp 刷 wa4300h.ipe 更新main APP 。。。。。无法写入！！！ 天呐！！！！不爽。。。黑线！！！
再SDRAM and RUN 不允许（之前在命令CLI中干了傻事，password-recover enable。。。。。)
CTRL+F格式化。。。。。。（出现问题。。。见下图。。。。）查store 没有东西，没有容量。。。。。不见了！！！！！
无语了。。。。。
之前还可以进系统，可能有希望。。。。现在运行不了。。。。
咋整？？？！！！！！！！！！！！
救命啊！！！！！
各种爬文爬贴。。。。找固件。。。。看能不能刷IK（爱快。。。集客）资料太少，心急啊。。。。没心情细看。。。。。
各种乱试。。。。。。无果！！！！！
————————————————————————————————————————————————
下午累了，早晨中午没吃饭啊。。。。。。老婆孩子回家了，煮了面，出去购物！！！GO！GO！GO！！！（换个心情，休息一下吧。。。。太累了。。。。）送孩子上兴趣班。。。。。
回家，接着干。。。。。。
换思路。。。。。。。。。。。。。。。。。。。。搞定。。。。。。。。。哈哈。。。。（卖个关子，大家看后面吧。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
————————————————————————————————————————————————
因部分操作内容后面的缓存冲掉了，没有之前出问题的操作部分（以后骚操作一定要把步骤给保留好，不能没步骤就乱上，一急就全忘！！！！！）。。。。问题部分只有借用其他贴子的（含图）。。。。请见谅。。。。。
借鉴了一些 WA4320H fit转fat后，flash无法被正确识别 的思路
找了很久想找固件没找到，刷也刷 不进去。
先前的思路：
1、可能是刷错版本，找版本。。。。心情一度差，都要C币，或是其他注册。。。。。而且不一定能解决问题
2、找ROM固件，找了全网没找到，能力有限,精力有限。。。其他就一天左右的时间。。。
先前wa4320h-fit 刷了wa4300h_fat.bin的包成功了。。。
之后wa4320h-fit 升级bootware成功（AC下自动升级的）
现在——
结果出现了这个问题，一直卡在后面，没办法下去了，请问这个该怎么解决啊？试着长摁RST也不行。
明显格式化操作中间少了一步。
还有恢复的可能，将这个AP先灌入V7 AP 的IPE版本，恢复到V7 FIT重新操作。
然后按照
参考如下案例：
https://zhiliao.h3c.com/Theme/details/5036
https://zhiliao.h3c.com/Theme/details/6184
如果是无AC方案的 中间存在格式化操作 一定不能做错
-------------------------------------------------------------------
经过一个晚上的摸索，终于解决了该问题。该问题的产生主要是因为V5和V7文件系统混乱造成的。1.使用编程器写入原fit模式下的编程器bootware固件，4M，必须是comware V7，可以从其他机器备份下来，也可以用fit然后用空填满4m。必须使用编程器，因为用bootware写入无效，bootware已经很混乱了。写入芯片为板载的25芯片，4M的。必须焊下来进行备份或写入，因为编程器的电源会使ap的cpu启动导致无法读取。编程器选用ch341或者minpro100均可以，不要买xtw100，驱动会有安装签名问题，比较麻烦，虽然在win10中也可以使用。
2.写入后再次启动时候，用micro USB转usb线直接连电脑，用超级终端会发现bootware启动后，版本已经变成7.多的。此时ctrl+b中断启动，ctrl+f格式化会发现可以格式化了，而且flash的文件系统回来了，也能够识别了。
3.后期再将fit转fat时候可以参考这篇。https://zhiliao.h3c.com/Theme/details/24566
唯一需要注意的是fit转fat，在将V7降级到V5时候，更新bootware前需要格式化flash，在更新bootware后同样需要格式化flash
最后更新好固件的时候，进入web管理端时候，查看文件是否已经写入到flash中，如果没有写入，必须把文件上传并且改为w4300_fat.bin,并设置为主文件。
————————————————————————————————————————————————————————————————————————
_____________________________________________________________________________________________________
下面进入正题》》》》》》》
_____________________________________________________________________________________________________
===============================<File CONTROL>===============================
|Note:the operating device is flash |
|<1> Display All File(s) |
|<2> Set Image File type |
|<3> Set Bin File type |
|<4> Set Configuration File type |
|<5> Delete File |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-5): 1
Display all file(s) in flash:
'M' = MAIN 'B' = BACKUP 'N/A' = NOT ASSIGNED
============================================================================
|NO. Size(B) Time Type Name |
============================================================================
===============================<File CONTROL>===============================
|Note:the operating device is flash |
|<1> Display All File(s) |
|<2> Set Image File type |
|<3> Set Bin File type |
|<4> Set Configuration File type |
|<5> Delete File |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-5): 0
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 3
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 5
==========================<ETHERNET PARAMETER SET>==========================
|Note: '.' = Clear field. |
| '-' = Go to previous field. |
| Ctrl+D = Quit. |
============================================================================
Protocol (FTP or TFTP) :tftp
Load File Name :wa4300_fat.bin
:wa4300h.ipe
Target File Name :wa4300_fat.bin
:wa4300h.ipe
Server IP Address :169.254.55.218 192.168.1.1
Local IP Address :169.254.55.216 192.168.1.2
Subnet Mask :255.255.0.0
Gateway IP Address :0.0.0.0
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 2
Loading.....................................................................
............................................................................
............................................................................
..........................................................Done.
14169088 bytes downloaded!
Something wrong with the file.
———————————————————————————————————————————————————————
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 1
Password recovery capability is disabled. To perform this operation, first
enable the password recovery capability using the password-recovery enable
command in CLI.
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 1
Password recovery capability is disabled. To perform this operation, first
enable the password recovery capability using the password-recovery enable
command in CLI.
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 3
Loading.....................................................................
............................................................................
............................................................................
..........................................................Done.
14169088 bytes downloaded!
Something wrong with the file.
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 4
Password recovery capability is disabled. To perform this operation, first
enable the password recovery capability using the password-recovery enable
command in CLI.
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 0
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 4
===============================<File CONTROL>===============================
|Note:the operating device is flash |
|<1> Display All File(s) |
|<2> Set Image File type |
|<3> Set Bin File type |
|<4> Set Configuration File type |
|<5> Delete File |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-5): 1
Display all file(s) in flash:
'M' = MAIN 'B' = BACKUP 'N/A' = NOT ASSIGNED
============================================================================
|NO. Size(B) Time Type Name |
============================================================================
===============================<File CONTROL>===============================
|Note:the operating device is flash |
|<1> Display All File(s) |
|<2> Set Image File type |
|<3> Set Bin File type |
|<4> Set Configuration File type |
|<5> Delete File |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-5): 0
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 7
=========================<BootWare Operation Menu>==========================
|Note:the operating device is flash |
|<1> Backup Full BootWare |
|<2> Restore Full BootWare |
|<3> Update BootWare By Serial |
|<4> Update BootWare By Ethernet |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-4): 4
===================<BOOTWARE OPERATION ETHERNET SUB-MENU>===================
|<1> Update Full BootWare |
|<2> Update Extended BootWare |
|<3> Update Basic BootWare |
|<4> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-4): 1
Loading.....................................................................
............................................................................
............................................................................
..........................................................Done.
14169088 bytes downloaded!
Something wrong with the file.
===================<BOOTWARE OPERATION ETHERNET SUB-MENU>===================
|<1> Update Full BootWare |
|<2> Update Extended BootWare |
|<3> Update Basic BootWare |
|<4> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-4): 0
=========================<BootWare Operation Menu>==========================
|Note:the operating device is flash |
|<1> Backup Full BootWare |
|<2> Restore Full BootWare |
|<3> Update BootWare By Serial |
|<4> Update BootWare By Ethernet |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-4): 0
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9):
=========================<EXTENDED ASSISTANT MENU>==========================
|<1> Display Memory |
|<2> Search Memory |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-2): 1
Info: Press Ctrl+C to abort or return to EXTENDED ASSISTANT MENU.
Info: Enter the address and length in hexadecimal notation.
Info: Only 4 bytes mode supported.
Enter memory address:
=========================<EXTENDED ASSISTANT MENU>==========================
|<1> Display Memory |
|<2> Search Memory |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-2): 0
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): ----------》》》》这是换固件，用了wa4300.ipe不是wa4300h.ipe(改名无效)18M的，这里是关键，要刷回V7版本的（含boot.bin和system.bin二个文件）tftp下载
Warning:All files on flash will be lost! Are you sure to format? [Y/N]Y.....
............................................................................
...............................................
Format success.
有了这一部，flash已经找回来了，但是还是不能刷入bootware baisic ，flash内没有内容
接着来吧！
_______________________________________________________________________________________
Press Ctrl+B to access EXTENDED-BOOTWARE MENU...
Loading the main boot and system image files...
The system image does not exist!
Loading the backup boot and system image files...
The image does not exist!
Booting image fails!
Trying to get the IP address from the DHCP server......
Getting IP Address Failed, the system will reboot.
[State : Idle] Reset request, rebooting the AP
Rebooting......
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing...................................
......Done!
****************************************************************************
* *
* H3C WA4320H-ACN BootWare, Version 7.14 *
* *
****************************************************************************
Copyright (c) 2004-2020 New H3C Technologies Co., Ltd.
Compiled Date : Jul 9 2020
CPU Type : ATHEROS AR9557
CPU L1 Cache : 32KB
CPU Clock Speed : 720MHz
Memory Type : DDR2 SDRAM
Memory Size : 256MB
Memory Speed : 560MHz
BootWare Size : 512KB
Flash Size : 128MB
PCB Version : Ver.B
BootWare Validating...
Press Ctrl+B to access EXTENDED-BOOTWARE MENU...
Loading the main boot and system image files...
The system image does not exist!
Loading the backup boot and system image files...
The image does not exist!
Booting image fails!
Trying to get the IP address from the DHCP server......
Getting IP Address Failed, the system will reboot.
[State : Idle] Reset request, rebooting the AP
Rebooting......
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing...................................
......Done!
****************************************************************************
* *
* H3C WA4320H-ACN BootWare, Version 7.14 *
* *
****************************************************************************
Copyright (c) 2004-2020 New H3C Technologies Co., Ltd.
Compiled Date : Jul 9 2020
CPU Type : ATHEROS AR9557
CPU L1 Cache : 32KB
CPU Clock Speed : 720MHz
Memory Type : DDR2 SDRAM
Memory Size : 256MB
Memory Speed : 560MHz
BootWare Size : 512KB
Flash Size : 128MB
PCB Version : Ver.B
BootWare Validating...
Press Ctrl+B to access EXTENDED-BOOTWARE MENU...
Loading the main boot and system image files...
The system image does not exist!
Loading the backup boot and system image files...
The image does not exist!
Booting image fails!
Trying to get the IP address from the DHCP server......
Getting IP Address Failed, the system will reboot.
[State : Idle] Reset request, rebooting the AP
Rebooting......
还是不行啊，进不去啊，怎么办哦。。。。。。
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing...................................
......Done!
****************************************************************************
* *
* H3C WA4320H-ACN BootWare, Version 7.14 *
* *
****************************************************************************
Copyright (c) 2004-2020 New H3C Technologies Co., Ltd.
Compiled Date : Jul 9 2020
CPU Type : ATHEROS AR9557
CPU L1 Cache : 32KB
CPU Clock Speed : 720MHz
Memory Type : DDR2 SDRAM
Memory Size : 256MB
Memory Speed : 560MHz
BootWare Size : 512KB
Flash Size : 128MB
PCB Version : Ver.B
BootWare Validating...
Press Ctrl+B to access EXTENDED-BOOTWARE MENU...
Password recovery capability is disabled.
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9):
Warning:All files on flash will be lost! Are you sure to format? [Y/N]Y.....
............................................................................
...............................................
Format success.
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 9
==============================<DEVICE CONTROL>==============================
|<1> Display All Available Nonvolatile Storage Device(s) |
|<2> Set The Operating Device |
|<3> Set The Default Boot Device |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-3): 1
Display all available nonvolatile storage device(s):
============================================================================
|NO. Device Name File System Total Size Available Space |
|1 flash YAFFS2 131072KB 129920KB |
============================================================================
==============================<DEVICE CONTROL>==============================
|<1> Display All Available Nonvolatile Storage Device(s) |
|<2> Set The Operating Device |
|<3> Set The Default Boot Device |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-3): 0
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 4
===============================<File CONTROL>===============================
|Note:the operating device is flash |
|<1> Display All File(s) |
|<2> Set Image File type |
|<3> Set Bin File type |
|<4> Set Configuration File type |
|<5> Delete File |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-5): 1
Display all file(s) in flash:
'M' = MAIN 'B' = BACKUP 'N/A' = NOT ASSIGNED
============================================================================
|NO. Size(B) Time Type Name |
============================================================================
===============================<File CONTROL>===============================
|Note:the operating device is flash |
|<1> Display All File(s) |
|<2> Set Image File type |
|<3> Set Bin File type |
|<4> Set Configuration File type |
|<5> Delete File |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-5): 0
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 3
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 5
==========================<ETHERNET PARAMETER SET>==========================
|Note: '.' = Clear field. |
| '-' = Go to previous field. |
| Ctrl+D = Quit. |
============================================================================
Protocol (FTP or TFTP) :tftp
Load File Name :wa4300_fat.bin
:wa4300h.ipe
Target File Name :wa4300_fat.bin
:wa4300h.ipe
Server IP Address :169.254.55.218 192.168.1.1
Local IP Address :169.254.55.216 192.168.1.2
Subnet Mask :255.255.0.0
Gateway IP Address :0.0.0.0
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 2
Loading.....................................................................
............................................................................
............................................................................
..........................................................Done.
14169088 bytes downloaded!
Something wrong with the file.
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 1
Password recovery capability is disabled. To perform this operation, first
enable the password recovery capability using the password-recovery enable
command in CLI.
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 1
Password recovery capability is disabled. To perform this operation, first
enable the password recovery capability using the password-recovery enable
command in CLI.
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 3
Loading.....................................................................
............................................................................
............................................................................
..........................................................Done.
14169088 bytes downloaded!
Something wrong with the file.
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 4
Password recovery capability is disabled. To perform this operation, first
enable the password recovery capability using the password-recovery enable
command in CLI.
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 0
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 4
===============================<File CONTROL>===============================
|Note:the operating device is flash |
|<1> Display All File(s) |
|<2> Set Image File type |
|<3> Set Bin File type |
|<4> Set Configuration File type |
|<5> Delete File |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-5): 1
Display all file(s) in flash:
'M' = MAIN 'B' = BACKUP 'N/A' = NOT ASSIGNED
============================================================================
|NO. Size(B) Time Type Name |
============================================================================
===============================<File CONTROL>===============================
|Note:the operating device is flash |
|<1> Display All File(s) |
|<2> Set Image File type |
|<3> Set Bin File type |
|<4> Set Configuration File type |
|<5> Delete File |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-5): 0
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 7
=========================<BootWare Operation Menu>==========================
|Note:the operating device is flash |
|<1> Backup Full BootWare |
|<2> Restore Full BootWare |
|<3> Update BootWare By Serial |
|<4> Update BootWare By Ethernet |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-4): 4
===================<BOOTWARE OPERATION ETHERNET SUB-MENU>===================
|<1> Update Full BootWare |
|<2> Update Extended BootWare |
|<3> Update Basic BootWare |
|<4> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-4): 1
Loading.....................................................................
............................................................................
............................................................................
..........................................................Done.
14169088 bytes downloaded!
Something wrong with the file.
===================<BOOTWARE OPERATION ETHERNET SUB-MENU>===================
|<1> Update Full BootWare |
|<2> Update Extended BootWare |
|<3> Update Basic BootWare |
|<4> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-4): 0
=========================<BootWare Operation Menu>==========================
|Note:the operating device is flash |
|<1> Backup Full BootWare |
|<2> Restore Full BootWare |
|<3> Update BootWare By Serial |
|<4> Update BootWare By Ethernet |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-4): 0
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9):
=========================<EXTENDED ASSISTANT MENU>==========================
|<1> Display Memory |
|<2> Search Memory |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-2): 1
Info: Press Ctrl+C to abort or return to EXTENDED ASSISTANT MENU.
Info: Enter the address and length in hexadecimal notation.
Info: Only 4 bytes mode supported.
Enter memory address:
=========================<EXTENDED ASSISTANT MENU>==========================
|<1> Display Memory |
|<2> Search Memory |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-2): 0
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9):
Warning:All files on flash will be lost! Are you sure to format? [Y/N]Y.....
............................................................................
...............................................
Format success.
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 3
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 5
==========================<ETHERNET PARAMETER SET>==========================
|Note: '.' = Clear field. |
| '-' = Go to previous field. |
| Ctrl+D = Quit. |
============================================================================
Protocol (FTP or TFTP) :tftp
Load File Name :wa4300h.ipe
:wa4300_fat.bin
Target File Name :wa4300h.ipe
:wa4300_fat.bin
Server IP Address :192.168.1.1
Local IP Address :192.168.1.2
Subnet Mask :255.255.0.0
Gateway IP Address :0.0.0.0
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 1
Password recovery capability is disabled. To perform this operation, first
enable the password recovery capability using the password-recovery enable
command in CLI. 还是失败。。。不过比刚才好，flash找回来了，找到组织了！！。。。
接着来。。。。。。。。。。。。。
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 0
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 0
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing...................................
......Done!
****************************************************************************
* *
* H3C WA4320H-ACN BootWare, Version 7.14 *
* 这里很重要。。。。 *
****************************************************************************
Copyright (c) 2004-2020 New H3C Technologies Co., Ltd.
Compiled Date : Jul 9 2020
CPU Type : ATHEROS AR9557
CPU L1 Cache : 32KB
CPU Clock Speed : 720MHz
Memory Type : DDR2 SDRAM
Memory Size : 256MB
Memory Speed : 560MHz
BootWare Size : 512KB
Flash Size : 128MB
PCB Version : Ver.B
BootWare Validating...
Press Ctrl+B to access EXTENDED-BOOTWARE MENU...
Loading the main boot and system image files...
The system image does not exist!
Loading the backup boot and system image files...
The image does not exist!
Booting image fails!
Trying to get the IP address from the DHCP server......———》》》》这里没有IP，我们给他找。。。看他要干什么。。。
DHCP server's IP address is 192.168.1.251 ———》》》》来了。。。。
Client's assigned address is 192.168.1.30
DNS domain name got from DHCP server is
DNS server's IP address is 192.168.1.251
Default Gateway's IP address is 192.168.1.251
This client's subnet mask is 255.255.255.0
The length of option 43 is: 0 ———》》》》有戏哦！！！！！！
Change State : Idle to Broadcast Discovery
Change State : Broadcast Discovery to Join
Change State : Join to JoinAck
Change State : JoinCfm to Image Download
Change State : Idle to Broadcast Discovery
Change State : Broadcast Discovery to Join
Change State : Join to JoinAck
Change State : JoinCfm to Image Download
Can't download the image from network, please check the network settings ————》》》要干什么？？
The system will reboot
[State : Idle] Reset request, rebooting the AP
Rebooting......
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing...................................
......Done!
****************************************************************************
* *
* H3C WA4320H-ACN BootWare, Version 7.14 *
* *
****************************************************************************
Copyright (c) 2004-2020 New H3C Technologies Co., Ltd.
Compiled Date : Jul 9 2020
CPU Type : ATHEROS AR9557
CPU L1 Cache : 32KB
CPU Clock Speed : 720MHz
Memory Type : DDR2 SDRAM
Memory Size : 256MB
Memory Speed : 560MHz
BootWare Size : 512KB
Flash Size : 128MB
PCB Version : Ver.B
BootWare Validating...
Press Ctrl+B to access EXTENDED-BOOTWARE MENU...
Loading the main boot and system image files...
The system image does not exist!
Loading the backup boot and system image files...
The image does not exist!
Booting image fails!
Trying to get the IP address from the DHCP server......
DHCP server's IP address is 192.168.1.251
Client's assigned address is 192.168.1.30
DNS domain name got from DHCP server is
DNS server's IP address is 192.168.1.251
Default Gateway's IP address is 192.168.1.251
This client's subnet mask is 255.255.255.0
The length of option 43 is: 0
Change State : Idle to Broadcast Discovery
Change State : Broadcast Discovery to Join
Change State : Join to JoinAck
Change State : JoinCfm to Image Download
Change State : Idle to Broadcast Discovery
Change State : Broadcast Discovery to Join
Change State : Join to JoinAck
Change State : JoinCfm to Image Download
Can't download the image from network, please check the network settings
The system will reboot
[State : Idle] Reset request, rebooting the AP
Rebooting......
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing...................................
......Done!
****************************************************************************
* *
* H3C WA4320H-ACN BootWare, Version 7.14 *
* *
****************************************************************************
Copyright (c) 2004-2020 New H3C Technologies Co., Ltd.
Compiled Date : Jul 9 2020
CPU Type : ATHEROS AR9557
CPU L1 Cache : 32KB
CPU Clock Speed : 720MHz
Memory Type : DDR2 SDRAM
Memory Size : 256MB
Memory Speed : 560MHz
BootWare Size : 512KB
Flash Size : 128MB
PCB Version : Ver.B
BootWare Validating...
Press Ctrl+B to access EXTENDED-BOOTWARE MENU...
Loading the main boot and system image files...
The system image does not exist!
Loading the backup boot and system image files...
The image does not exist!
Booting image fails!
Trying to get the IP address from the DHCP server......
DHCP server's IP address is 192.168.1.251
Client's assigned address is 192.168.1.30
DNS domain name got from DHCP server is
DNS server's IP address is 192.168.1.251
Default Gateway's IP address is 192.168.1.251
This client's subnet mask is 255.255.255.0
The length of option 43 is: 0
Change State : Idle to Broadcast Discovery
Change State : Broadcast Discovery to Join
Change State : Join to JoinAck
Change State : JoinCfm to Image Download
Change State : Idle to Broadcast Discovery
Change State : Broadcast Discovery to Join
Change State : Join to JoinAck
Change State : JoinCfm to Image Download
Can't download the image from network, please check the network settings
The system will reboot
[State : Idle] Reset request, rebooting the AP
Rebooting......
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing...................................
......Done!
****************************************************************************
* *
* H3C WA4320H-ACN BootWare, Version 7.14 *
* *
****************************************************************************
Copyright (c) 2004-2020 New H3C Technologies Co., Ltd.
Compiled Date : Jul 9 2020
CPU Type : ATHEROS AR9557
CPU L1 Cache : 32KB
CPU Clock Speed : 720MHz
Memory Type : DDR2 SDRAM
Memory Size : 256MB
Memory Speed : 560MHz
BootWare Size : 512KB
Flash Size : 128MB
PCB Version : Ver.B
BootWare Validating...
Press Ctrl+B to access EXTENDED-BOOTWARE MENU...
Loading the main boot and system image files...
The system image does not exist!
Loading the backup boot and system image files...
The image does not exist!
Booting image fails!
Trying to get the IP address from the DHCP server......
DHCP server's IP address is 192.168.1.251
Client's assigned address is 192.168.1.30
DNS domain name got from DHCP server is
DNS server's IP address is 192.168.1.251
Default Gateway's IP address is 192.168.1.251
This client's subnet mask is 255.255.255.0
The length of option 43 is: 0
Change State : Idle to Broadcast Discovery
Change State : Broadcast Discovery to Join
Change State : Join to JoinAck
Change State : JoinCfm to Image Download
Change State : Idle to Broadcast Discovery
Change State : Broadcast Discovery to Join
Change State : Join to JoinAck
Change State : JoinCfm to Image Download
Can't download the image from network, please check the network settings
The system will reboot
[State : Idle] Reset request, rebooting the AP
Rebooting......
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing...................................
......Done!
****************************************************************************
* *
* H3C WA4320H-ACN BootWare, Version 7.14 *
* *
****************************************************************************
Copyright (c) 2004-2020 New H3C Technologies Co., Ltd.
Compiled Date : Jul 9 2020
CPU Type : ATHEROS AR9557
CPU L1 Cache : 32KB
CPU Clock Speed : 720MHz
Memory Type : DDR2 SDRAM
Memory Size : 256MB
Memory Speed : 560MHz
BootWare Size : 512KB
Flash Size : 128MB
PCB Version : Ver.B
BootWare Validating...
Press Ctrl+B to access EXTENDED-BOOTWARE MENU...
Loading the main boot and system image files...
The system image does not exist!
Loading the backup boot and system image files...
The image does not exist!
Booting image fails!
Trying to get the IP address from the DHCP server......
DHCP server's IP address is 192.168.1.251
Client's assigned address is 192.168.1.30
DNS domain name got from DHCP server is
DNS server's IP address is 192.168.1.251
Default Gateway's IP address is 192.168.1.251
This client's subnet mask is 255.255.255.0
The length of option 43 is: 0
Change State : Idle to Broadcast Discovery
Change State : Broadcast Discovery to Join
Change State : Join to JoinAck
Change State : JoinCfm to Image Download ——————》》》上AC
........................................................
............................................................................
..............................................
Image file wa4300-boot.bin is self-decompressing...
Saving file flash:/wa4300-boot.bin .........Done.
Image file wa4300-system.bin is self-decompressing...
Saving file flash:/wa4300-system.bin .......................................
.....Done.
Rebooting......
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing...................................
......Done!
****************************************************************************
* *
* H3C WA4320H-ACN BootWare, Version 7.14 *
* *
****************************************************************************
Copyright (c) 2004-2020 New H3C Technologies Co., Ltd.
Compiled Date : Jul 9 2020
CPU Type : ATHEROS AR9557
CPU L1 Cache : 32KB
CPU Clock Speed : 720MHz
Memory Type : DDR2 SDRAM
Memory Size : 256MB
Memory Speed : 560MHz
BootWare Size : 512KB
Flash Size : 128MB
PCB Version : Ver.B
BootWare Validating...
Press Ctrl+B to access EXTENDED-BOOTWARE MENU...
Loading the main boot and system image files...
Loading file flash:/wa4300-system.bin.................Done.
Loading file flash:/wa4300-boot.bin......Done.
Basic BootWare Version is not equal,updating? [Y/N]
Updating Basic BootWare..........Done.
BootWare updated,System is rebooting now.
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing...................................
......Done!
****************************************************************************
* *
* H3C WA4320H-ACN BootWare, Version 7.14 *
* *
****************************************************************************
Copyright (c) 2004-2020 New H3C Technologies Co., Ltd.
Compiled Date : Jul 9 2020
CPU Type : ATHEROS AR9557
CPU L1 Cache : 32KB
CPU Clock Speed : 720MHz
Memory Type : DDR2 SDRAM
Memory Size : 256MB
Memory Speed : 560MHz
BootWare Size : 512KB
Flash Size : 128MB
PCB Version : Ver.B
BootWare Validating...
Press Ctrl+B to access EXTENDED-BOOTWARE MENU...
Loading the main boot and system image files... ——————》》》》来了！！！！！。。。。
Loading file flash:/wa4300-system.bin.................Done.
Loading file flash:/wa4300-boot.bin......Done.
Image file flash:/wa4300-boot.bin is self-decompressing.....................
............................................................................
............................................................................
............................................................................
..........Done.
System image is starting...
Startup configuration file doesn't exist or is invalid.
Line con0 is available.
Press ENTER to get started. ————————》》成功进系统！！！！祝贺一下，爽！！！！
<H3C>%Oct 16 13:56:33:752 2020 H3C SHELL/5/SHELL_LOGIN: Console logged in from con0.
<H3C>sys
<H3C>system-view re
<H3C>system-view
System View: return to User View with Ctrl+Z.
[H3C]pa
[H3C]pas
[H3C]password-r
[H3C]dis %Oct 17 15:24:58:695 2020 50da-0013-2460 CWC/6/CWC_AP_UP: Master CAPWAP tunnel to AC 192.168.1.8 went up.
%Oct 17 15:24:58:879 2020 50da-0013-2460 STAMGR/6/SERVICE_ON: BSS 50da-0013-2460 was created after service template wireless with SSID Z-AP was bound to radio 1 on AP FitAP.
%Oct 17 15:24:58:927 2020 50da-0013-2460 STAMGR/6/SERVICE_ON: BSS 50da-0013-2470 was created after service template wireless with SSID Z-AP was bound to radio 2 on AP FitAP.
pa
[50da-0013-2460]dis pas
[50da-0013-2460]dis password-control
[50da-0013-2460]dis password-cont
[50da-0013-2460]dis password-
[50da-0013-2460]dis password-control
[50da-0013-2460]dis password-control
[50da-0013-2460]dis password-re
[50da-0013-2460]dis password-re
[50da-0013-2460]pa
[50da-0013-2460]packet-filter
[50da-0013-2460]password-control
[50da-0013-2460]password-recovery enab
[50da-0013-2460]password-recovery enable ——————》》》》》》映像深刻啊。。。
[50da-0013-2460]reboot
^
% Unrecognized command found at '^' position.
[50da-0013-2460]quit
<50da-0013-2460>dir
Directory of flash:
0 -rw- 2695168 Aug 08 2008 20:00:00 wa4300-boot.bin
1 -rw- 15572992 Aug 08 2008 20:00:00 wa4300-system.bin
131072 KB total (112200 KB free)
<50da-0013-2460>tftp
<50da-0013-2460>tftp 192.168.1.20
<50da-0013-2460>tftp 192.168.1.20
<50da-0013-2460>tftp 192.168.1.20
<50da-0013-2460>tftp 192.168.1.20 ?
get Download a file from the TFTP server
put Upload a local file to the TFTP server
sget Download a file from the TFTP server securely
<50da-0013-2460>tftp 192.168.1.20 put
<50da-0013-2460>tftp 192.168.1.20 put
<50da-0013-2460>tftp 192.168.1.20 put
<50da-0013-2460>tftp 192.168.1.20 put ?
STRING [drive][path][file name]
flash: Device name
slot1#flash: Device name
<50da-0013-2460>tftp 192.168.1.20 put f
<50da-0013-2460>tftp 192.168.1.20 put flash:/ *.*
^
% Wrong parameter found at '^' position.
<50da-0013-2460>tftp 192.168.1.20 put flash:/*.*
^
% Wrong parameter found at '^' position.
<50da-0013-2460>tftp 192.168.1.20 put flash:/w
<50da-0013-2460>tftp 192.168.1.20 put flash:/wa4300-b
<50da-0013-2460>tftp 192.168.1.20 put flash:/wa4300-boot.bin
Press CTRL+C to abort.
% Total % Received % Xferd Average Speed Time Time Time Current
Dload Upload Total Spent Left Speed
100 2632k 0 0 100 2632k 0 211k 0:00:12 0:00:12 --:--:-- 226k ———》》》备份一下，下次用
<50da-0013-2460>tftp 192.168.1.20 put flash:/wa4300-s
<50da-0013-2460>tftp 192.168.1.20 put flash:/wa4300-system.bin
Press CTRL+C to abort.
% Total % Received % Xferd Average Speed Time Time Time Current
Dload Upload Total Spent Left Speed
100 14.8M 0 0 100 14.8M 0 218k 0:01:09 0:01:09 --:--:-- 223k ———》》》备份一下，下次用
<50da-0013-2460>
******************************************************************************
* Copyright (c) 2004-2020 New H3C Technologies Co., Ltd. All rights reserved.*
* Without the owner's prior written consent, *
* no decompiling or reverse-engineering shall be allowed. *
******************************************************************************
Line con0 is available.
Press ENTER to get started.
******************************************************************************
* Copyright (c) 2004-2020 New H3C Technologies Co., Ltd. All rights reserved.*
* Without the owner's prior written consent, *
* no decompiling or reverse-engineering shall be allowed. *
******************************************************************************
Line con0 is available.
Press ENTER to get started.
******************************************************************************
* Copyright (c) 2004-2020 New H3C Technologies Co., Ltd. All rights reserved.*
* Without the owner's prior written consent, *
* no decompiling or reverse-engineering shall be allowed. *
******************************************************************************
Line con0 is available.
Press ENTER to get started.
又回到了 V7 comware
恢复到V7的关键：1、刷回V7的版本，AC一定要配置好；
2、一定要上传wa4300.ipe的固件在AC内；
3、一定要联上网络，最好直连AC；
4、特别提醒：要格式化！！！！！！！！！！！！！！！降级不能不格式化就刷机。。。！！！！！！！
耐心等吧，
各种骚操作试试 V7变回V5试试，直接变胖FAT，刷。。。2020-10-26相关推荐
- 显卡刷bios变砖怎么办--关于矿卡，一些惊呆我的骚操作
趁着双11的热度,也体验了一把什么叫做矿卡? 选择的是三战老兵,矿卡重灾区的RX580系列,价格不到300的XFX RX580 8G 2304满血版,商家是这么描述的,估且信着吧,商家还很好心的提示, ...
- 骚操作！图片缩小后 内容竟变得完全不同？
点击上方"AI算法与图像处理",选择加"星标"或"置顶" 重磅干货,第一时间送达 编辑:AI算法与图像处理 仅作为学习交流分享,如有侵权请联 ...
- 广告投放的那些骚操作
作者:梁丽丽(Lily Leung),中国第一批程序化广告从业者,<程序化广告>作者,并著有网络白皮书<程序化广告生态实用手册>及<品牌程序化广告投放指南>,暨南大 ...
- Git科普文，Git基本原理各种骚操作
Git简单介绍 Git是一个分布式版本控制软件,最初由Linus Torvalds创作,于2005年以GPL发布.最初目的是为更好地管理Linux内核开发而设计. Git工作流程以及各个区域 Wo ...
- lisp 提取字符串中的數字_Redis 数据结构之字符串的那些骚操作
Redis 字符串底层用的是 sds 结构,该结构同 c 语言的字符串相比,其优点是可以节省内存分配的次数,还可以... 这样写是不是读起来很无聊?这些都是别人咀嚼过后,经过一轮两轮三轮的再次咀嚼,吐 ...
- js控制台 console 骚操作-打印图片-自定义样式-字符画
目录 控制台打印骚操作 自定义样式 打印(输出)图片 借助平台打印字符(符号组成) Lunicode 平台操作 图片转字符打印 控制台打印骚操作二 效果图 代码实现 错误案例 方式一(感觉有点乱) 方 ...
- 公司里开发用的机器，虚拟机、网络、转发、ssh连接、远程桌面、远程开机……等一系列骚操作的操作概述
我这里讲的都是如何回家后还可以连接公司电脑,且省电.不伤机器的事啊,审核的各位别误会了. 这篇就不要提docker了,两码事. 也不要纠结什么hyperV.virtualBox还是vmware的了,无 ...
- 就决定是你啦！苏菲婆5！ —— 谈谈我对Surface Pro 5的使用体验以及各种骚操作
原文发布于:https://bili33.top/posts/Enchance-my-Surface-Pro-5/ 今年的九月份,我卖掉了我的老联想 Yoga 370,然后购置了一台Surface P ...
- python separator_Python 必知的 20 个骚操作！
原标题:Python 必知的 20 个骚操作! 如有好文章投稿,请点击 → 这里了解详情 记住常见的 Python 技巧,可以帮助改善代码设计,减少出错,节省时间. 作者 | Chaitanya Ba ...
最新文章
- Java NIO编程的技巧和陷阱
- 使用SAT跟踪监控从浏览器打开的SAP应用的性能和调用栈
- ASCII码与字符串的相互转换
- 液位系统c语言程序,超声波自动测量物体液位系统的设计
- WM中的OutLook开发和操作
- 前端学习（2988）：vue+element今日头条管理--使用技术栈
- nod32更新服务无法设置问题更改
- 安装vs 2015 社区版
- python爬取别人qq空间相册_python+selenium+requests爬取qq空间相册时遇到的问题及解决思路...
- QQ聊天记录的备份和恢复（含迁移与合并）
- 使用scrapy刷博客访问量(傻瓜式)
- Android 入门宝典 - inflate 生成视图 动态加载视图
- 移动智能时代，为何还需要猎网平台？
- 二维数组malloc申请空间以及初始化方式
- RSA生成公私钥并加解密
- 回顾2018年云计算九大亮点
- Android自定义控件----继承ViewGroup侧滑菜单5，抽屉式侧滑，QQ5.0效果（完结）
- CSUST 2007 我爱吃烧烤 （状压dp）
- matlab 眼睛的精确识别,整天对着电脑手机,如何保护好自己的眼睛?AI+眼镜了解一下!...
- 直击平昌! 2天40位大咖的平昌区块链论坛精华都在这了！