Aruba

交换机基本操作命令

登录：

(Aruba2400)

User: admin

Password: *****(缺省口令通常是admin)

NOTICE

NOTICE -- This switch has active licenses that will expire in 26 days

NOTICE

NOTICE -- See 'show license' for details.

NOTICE

(Aruba2400) >en

Password:*****(缺省口令通常是admin)

(Aruba2400) #

恢复出厂值：

(Aruba2400) #write erase

All the configuration will be deleted. Press 'y' to proceed :

Write Erase successful

(Aruba2400) #reload

Do you really want to reset the system(y/n): y

��������

Aruba交换机重启

��������

初始化配置：

Enter System name [Aruba2400]:

Enter VLAN 1 interface IP address [172.16.0.254]:

Enter VLAN 1 interface subnet mask [255.255.255.0]:

Enter IP Default gateway [none]:

Enter Switch Role, (master|local) [master]:

Enter Country code (ISO-3166), for supported list: CN

You have chosen Country code CN for

China (yes|no)?: y

Enter Password for admin login (up to 32 chars): *****

Re-type Password for admin login: *****

Enter Password for enable mode (up to 15 chars): *****

Re-type Password for enable mode: *****

Do you wish to shutdown all the ports (yes|no)? [no]:

Current choices are:

System name: Aruba2400

VLAN 1 interface IP address: 172.16.0.254

VLAN 1 interface subnet mask: 255.255.255.0

IP Default gateway: none

Switch Role: master

Country code: CN

Ports shutdown: no

If you accept the changes the switch will restart!

Type to go back and change answer for any question

Do you wish to accept the changes (yes|no)y

Creating configuration... Done.

保存配置参数：

(Aruba2400) #configure t

(Aruba2400) #write m

保存配置文件：

(Aruba2400) >en

Password:*****

(Aruba2400) #configure t

(Aruba2400) # copy running-config tftp: 192.168.4.100 aruba2400-0904.cfg

恢复配置文件：

(Aruba2400) >en

Password:*****

(Aruba2400) #configure t

(Aruba2400) (config) #copy tftp: 172.16.0.100 aruba2400-0904.cfg flash: 2400.bak

(Aruba2400) (config) #copy flash: 2400.bak flash: 2400.cfg

(Aruba2400) (config) #boot config-file 2400.cfg

(Aruba2400) (config) #reload

Do you really want to reset the system(y/n): y

System will now restart!

Image升级：

(Aruba200) #show boot

Config File: default.cfg

Boot Partition: PARTITION 0

(Aruba2400) #show image version

(Aruba2400) #copy tftp: 172.16.1.50 A2400_FCS2.0.X_6577 system: partition 1

Upgrading partition 1

(Aruba2400) #reload

(Aruba200) #boot system partition 1

PC：SOE

重启AP

2秒内Stop

>purge

>save

>boot

A800：

login as: admin

admin@10.3.22.20's password:

(Aruba-master) >enable

Password:******

(Aruba-master) #configure terminal

Enter Configuration commands, one per line. End with CNTL/Z

(Aruba-master) (config) #telnet soe

telnet 172.16.0.254 2300

connect 1/2

Once SOE is enabled, you can connect to the AP serial port with the following procedure:

1

Telnet to the

Aruba mobility controller using port 2300

2

Log in using the admin account

3

Connect to the Ethernet port that the AP is attached to

User: admin

Password: *****

Available commands:

connect

exit (no args)

soe> connect 2/0

Connecting to 2/0 at 9600 baud 8N1

Type "~." to disconnect

本文出自 “

butter520” 博客，转载请与作者联系！

本文出自 51CTO.COM技术博客