作者主页(文火冰糖的硅基工坊)：文火冰糖（王文兵）的博客_文火冰糖的硅基工坊_CSDN博客

本文网址：https://blog.csdn.net/HiWangWenBing/article/details/120524557

目录

前言：

第1章 LTE协议栈

第2章 OpenAirInterface 4G LTE eNB Feature Set

2.1 eNB PHY Layer

3.2 Performances

3.3 Number of supported UEs

3.4 eNB MAC Layer

3.4 eNB RLC Layer

3.5 eNB PDCP Layer

3.6 eNB RRC Layer

3.7 eNB X2AP

3.8 eNB/MCE M2AP

3.9 MCE/MME M3AP （与MME的接口）

第4章 OpenAirInterface 4G LTE UE Feature Set

4.1 LTE UE PHY Layer

4.2 LTE UE MAC Layer

4.3 LTE UE RLC Layer

4.4 LTE UE PDCP Layer

4.5 LTE UE RRC Layer

4.5 LTE UE NAS Layer（与MME接口）

前言：

参考： doc/FEATURE_SET.md · develop · oai / openairinterface5G · GitLab

第1章 LTE协议栈

第2章 OpenAirInterface 4G LTE eNB Feature Set

2.1 eNB PHY Layer

The Physical layer implements 3GPP 36.211, 36.212, 36.213 and provides the following features:

  • LTE release 8.6 compliant, and implements a subset of release 10
  • FDD and TDD configurations: 1 (experimental) and 3
  • Bandwidth: 5, 10, and 20 MHz
  • Transmission modes: 1, 2 (stable), 3, 4, 5, 6, 7 (experimental)
  • Max number of antennas: 2 （不支持4T4R）
  • CQI/PMI reporting: aperiodic, feedback mode 3 - 0 and 3 - 1
  • PRACH preamble format 0
  • Downlink (DL) channels are supported: PSS, SSS, PBCH, PCFICH, PHICH, PDCCH, PDSCH, PMCH, MPDCCH
  • Uplink (UL) channels are supported: PRACH, PUSCH, PUCCH (format 1/1a/1b), SRS, DRS
  • HARQ support (UL and DL)
  • Highly optimized base band processing (including turbo decoder)
  • Multi-RRU support: over the air synchro b/ multi RRU in TDD mode
  • Support for CE-modeA for LTE-M. Limited support for repeatition, single-LTE-M connection, legacy-LTE UE attach is disabled.

3.2 Performances

Transmission Mode, Bandwidth Expected Throughput Measured Throughput Measurement Conditions
FDD DL: 5 MHz, 25 PRBS/ MCS 28 16 - 17 Mbit/s TM1: 17.0 Mbits/s COTS-UE Cat 4 (150/50 Mbps)
FDD DL: 10 MHz, 50 PRBS/ MCS 28 34 - 35 Mbit/s TM1: 34.0 Mbits/s COTS-UE Cat 4 (150/50 Mbps)
FDD DL: 20 MHz, 100 PRBS/ MCS 28 70 Mbit/s TM1: 69.9 Mbits/s COTS-UE Cat 4 (150/50 Mbps)
FDD UL: 5 MHz, 25 PRBS/ MCS 20 9 Mbit/s TM1: 8.28 Mbits/s COTS-UE Cat 4 (150/50 Mbps)
FDD UL: 10 MHz, 50 PRBS/ MCS 20 17 Mbit/s TM1: 18.3 Mbits/s COTS-UE Cat 4 (150/50 Mbps)
FDD UL: 20 MHz, 100 PRBS/ MCS 20 35 Mbit/s TM1: 18.6 Mbits/s COTS-UE Cat 4 (150/50 Mbps)
TDD DL: 5 MHz, 25 PRBS/ MCS XX 6.5 Mbit/s TM1: 6.71 Mbits/s COTS-UE Cat 4 (150/50 Mbps)
TDD DL: 10 MHz, 50 PRBS/ MCS XX 13.5 Mbit/s TM1: 13.6 Mbits/s COTS-UE Cat 4 (150/50 Mbps)
TDD DL: 20 MHz, 100 PRBS/ MCS XX 28.0 Mbit/s TM1: 27.2 Mbits/s COTS-UE Cat 4 (150/50 Mbps)
TDD UL: 5 MHz, 25 PRBS/ MCS XX 2.0 Mbit/s TM1: 3.31 Mbits/s COTS-UE Cat 4 (150/50 Mbps)
TDD UL: 10 MHz, 50 PRBS/ MCS XX 2.0 Mbit/s TM1: 7.25 Mbits/s COTS-UE Cat 4 (150/50 Mbps)
TDD UL: 20 MHz, 100 PRBS/ MCS XX 3.0 Mbit/s TM1: 4.21 Mbits/s COTS-UE Cat 4 (150/50 Mbps)

3.3 Number of supported UEs

  • 16 by default (16个用户)
  • up to 256 when compiling with dedicated compile flag （需要更多的计算资源）
  • was tested with 40 COTS-UE （40个用户是经过测试的）

3.4 eNB MAC Layer

The MAC layer implements a subset of the 3GPP 36.321 release v8.6 in support of BCH, DLSCH, RACH, and ULSCH channels.

  • RRC interface for CCCH, DCCH, and DTCH
  • Proportional fair scheduler (round robin scheduler soon), with the following improvements:
    • Up to 30 users tested in the L2 simulator, CCE allocation in the preprocessor ; the scheduler was also simplified and made more modular
    • Adaptative UL-HARQ
    • Remove out-of-sync UEs
    • No use of the first_rb in the UL scheduler ; respects vrb_map_UL and vrb_map in the DL
  • DCI generation
  • HARQ Support
  • RA procedures and RNTI management
  • RLC interface (AM, UM)
  • UL power control
  • Link adaptation
  • Connected DRX (CDRX) support for FDD LTE UE. Compatible with R13 from 3GPP. Support for Cat-M1 UE comming soon.

3.4 eNB RLC Layer

The RLC layer implements a full specification of the 3GPP 36.322 release v9.3.

  • RLC TM (mainly used for BCCH and CCCH)

    • Neither segment nor concatenate RLC SDUs
    • Do not include a RLC header in the RLC PDU
    • Delivery of received RLC PDUs to upper layers
  • RLC UM (mainly used for DTCH)
    • Segment or concatenate RLC SDUs according to the TB size selected by MAC
    • Include a RLC header in the RLC PDU
    • Duplication detection
    • PDU reordering and reassembly
  • RLC AM, compatible with 9.3
    • Segmentation, re-segmentation, concatenation, and reassembly
    • Padding
    • Data transfer to the user
    • RLC PDU retransmission in support of error control and correction
    • Generation of data/control PDUs

3.5 eNB PDCP Layer

The current PDCP layer is header compliant with 3GPP 36.323 Rel 10.1.0 and implements the following functions:

  • User and control data transfer
  • Sequence number management
  • RB association with PDCP entity
  • PDCP entity association with one or two RLC entities
  • Integrity check and encryption using the AES and Snow3G algorithms

3.6 eNB RRC Layer

The RRC layer is based on 3GPP 36.331 v15.6 and implements the following functions:

  • System Information broadcast (SIB 1, 2, 3, and 13)

    • SIB1: Up to 6 PLMN IDs broadcast
  • RRC connection establishment
  • RRC connection reconfiguration (addition and removal of radio bearers, connection release)
  • RRC connection release
  • RRC connection re-establishment
  • Inter-frequency measurement collection and reporting (experimental)
  • eMBMS for multicast and broadcast (experimental)
  • Handover (experimental)
  • Paging (soon)
  • RRC inactivity timer (release of UE after a period of data inactivity)

3.7 eNB X2AP

The X2AP layer is based on 3GPP 36.423 v14.6.0 and implements the following functions:

  • X2 Setup Request
  • X2 Setup Response
  • X2 Setup Failure
  • Handover Request
  • Handover Request Acknowledge
  • UE Context Release
  • X2 timers (t_reloc_prep, tx2_reloc_overall)
  • Handover Cancel
  • X2-U interface implemented
  • EN-DC is implemented
  • X2AP : Handling of SgNB Addition Request / Addition Request Acknowledge / Reconfiguration Complete
  • RRC : Handling of RRC Connection Reconfiguration with 5G cell info, configuration of 5G-NR measurements
  • S1AP : Handling of E-RAB Modification Indication / Confirmation

3.8 eNB/MCE M2AP

The M2AP layer is based on 3GPP 36.443 v14.0.1:

  • M2 Setup Request
  • M2 Setup Response
  • M2 Setup Failure
  • M2 Scheduling Information
  • M2 Scheduling Information Response
  • M2 Session Start Request
  • M2 Session Start Response

3.9 MCE/MME M3AP （与MME的接口）

The M3AP layer is based on 3GPP 36.444 v14.0.1:

  • M3 Setup Request
  • M3 Setup Response
  • M3 Setup Failure
  • M3 Session Start Request
  • M3 Session Start Response

备注：也就是说，可以支持与核心网MME的连接。

第4章 OpenAirInterface 4G LTE UE Feature Set

4.1 LTE UE PHY Layer

The Physical layer implements 3GPP 36.211, 36.212, 36.213 and provides the following features:

  • LTE release 8.6 compliant, and implements a subset of release 10
  • FDD and TDD configurations: 1 (experimental) and 3
  • Bandwidth: 5, 10, and 20 MHz
  • Transmission modes: 1, 2 (stable) =》 UE只支持mode1,2
  • Max number of antennas: 2 =》 两天线
  • CQI/PMI reporting: aperiodic, feedback mode 3 - 0 and 3 - 1
  • PRACH preamble format 0
  • All downlink (DL) channels are supported: PSS, SSS, PBCH, PCFICH, PHICH, PDCCH, PDSCH, PMCH
  • All uplink (UL) channels are supported: PRACH, PUSCH, PUCCH (format 1/1a/1b), SRS, DRS
  • LTE MBMS-dedicated cell (feMBMS) procedures subset for LTE release 14 (experimental)
  • LTE non-MBSFN subframe (feMBMS) Carrier Adquistion Subframe-CAS procedures (PSS/SSS/PBCH/PDSH) (experimental)
  • LTE MBSFN MBSFN subframe channel (feMBMS): PMCH (CS@1.25KHz) (channel estimation for 25MHz bandwidth) (experimental)

4.2 LTE UE MAC Layer

The MAC layer implements a subset of the 3GPP 36.321 release v8.6 in support of BCH, DLSCH, RACH, and ULSCH channels.

  • RRC interface for CCCH, DCCH, and DTCH
  • HARQ Support
  • RA procedures and RNTI management
  • RLC interface (AM, UM)
  • UL power control
  • Link adaptation
  • MBMS-dedicated cell (feMBMS) RRC interface for BCCH
  • eMBMS and MBMS-dedicated cell (feMBMS) RRC interface for MCCH, MTCH

4.3 LTE UE RLC Layer

The RLC layer implements a full specification of the 3GPP 36.322 release v9.3.

4.4 LTE UE PDCP Layer

The current PDCP layer is header compliant with 3GPP 36.323 Rel 10.1.0.

4.5 LTE UE RRC Layer

The RRC layer is based on 3GPP 36.331 v14.3.0 and implements the following functions:

  • System Information decoding
  • RRC connection establishment
  • MBMS-dedicated cell (feMBMS) SI-MBMS/SIB1-MBMS management

4.5 LTE UE NAS Layer（与MME接口）

The NAS layer is based on 3GPP 24.301 and implements the following functions:

  • EMM attach/detach, authentication, tracking area update, and more
  • ESM default/dedicated bearer, PDN connectivity, and more

作者主页(文火冰糖的硅基工坊)：文火冰糖（王文兵）的博客_文火冰糖的硅基工坊_CSDN博客

本文网址：https://blog.csdn.net/HiWangWenBing/article/details/120524557

[OpenAirInterface实战-4] ：OAI支持的4G LTE功能集相关推荐

  1. [OpenAirInterface实战-1] ：什么是OAI？OAI常见问题解答

    作者主页(文火冰糖的硅基工坊):文火冰糖(王文兵)的博客_文火冰糖的硅基工坊_CSDN博客 本文网址:https://blog.csdn.net/HiWangWenBing/article/detai ...

  2. [OpenAirInterface实战-7] ：OAI编译环境的架构、搭建、目标代码的编译

    作者主页(文火冰糖的硅基工坊):文火冰糖(王文兵)的博客_文火冰糖的硅基工坊_CSDN博客 本文网址:https://blog.csdn.net/HiWangWenBing/article/detai ...

  3. 如何搭建并使用便携式 4G/LTE 伪基站研究移动安全

    此文章PDF文档下载地址:点击下载 0x00 前言 在移动互联网深入普及和物联网开始规模应用的今天,网络安全公司怎能不研究移动安全,要研究移动安全,怎能没有4G/LTE伪基站研究测试环境? 本文介绍如 ...

  4. OAI支持的SDR射频硬件平台概述

    1. 4G LTE OAI支持的SDR 射频硬件平台 OAI的设计也是与射频硬件平台无关,在OAI官网能查到的 LTE正式支持的硬件平台有: 1.    USRP B210 http://www.et ...

  5. GitChat·安全 | 搭建并使用便携式 4G/LTE 伪基站研究移动安全

    GitChat 作者:Seeker 前言 在移动互联网深入普及和物联网开始规模应用的今天,网络安全公司怎能不研究移动安全,要研究移动安全,怎能没有4G/LTE伪基站研究测试环境? 本文介绍如何利用开源 ...

  6. [4G5G专题-79]：流程 - 4G LTE 寻呼流程Paging

    目录 第1章 L3层信令架构 1.1 RAN协议栈 1.2 信令流与数据流 1.3 信道映射 1.4 连接管理 1.5 手机附着的整体流程 1.6 无线承载 1.7 RRC连接状态 第2章 寻呼概述 ...

  7. 4G LTE概念以及VoLTE

    LTE是指长期演进技术(英语:Long Term Evolution,常简写为LTE),商业宣传上通常被称作4G LTE,但事实上是3.5G下HSDPA迈向4G的过度版本.也曾经被俗称为3.9G,直到 ...

  8. 4G LTE浪潮何时席卷全球？

    随着4G LTE的不断渗入,全球无线运营商应该联合起来,但国际漫游是其中最主要的一个棘手问题. 现在美国的iPad用户,以及其他4G LTE智能手机和平板用户还不能进行4G LTE国际漫游.但将来是否 ...

  9. [4G5G基础学习]：流程 - 4G LTE 核心网的Attach流程

    版权声明:本文为CSDN博主「文火冰糖的硅基工坊」的原创文章:[4G&5G专题-78]:流程 - 4G LTE 核心网的Attach流程 , 转载链接 第1章 L3层信令架构 1.1 RAN协 ...

最新文章

  1. oracle最大实例数,【Oracle】RAC的多实例数据迁移至单机的多实例。
  2. 尝试HTML + JavaScript 编写Windows App
  3. 记录安装mysql5.7.24遇到的坑
  4. 微信小程序php get_php处理微信小程序request请求
  5. 使用应用编排服务一键式部署,持续集成利器--jenkins
  6. 13.Excel业务建模——RFM模型
  7. javafx中的tree_JavaFX中的塔防（6）
  8. 使用java 遍历文件夹
  9. linux能力集机制,linux能力机制
  10. 迅雷精简版 for Mac！附精简教程！
  11. Redis 中的 standalone（单机模式）配置说明和分析
  12. Java使用FFmpeg（自定义cmd）系列之MP4 转码 HLS m3u8 AES128 加密
  13. 服务器日志修改保存时间,日志服务保留时间
  14. 本地与云服务器（阿里云）实现多客户端虚拟局域网搭建
  15. 超过100w条数据表的分页查询优化
  16. 大数据开发基础入门与项目实战（三）Hadoop核心及生态圈技术栈之2.HDFS分布式文件系统
  17. 徽章插件_为您的未来项目免费徽章PSD和矢量集
  18. RK3588 RGA 图像操作
  19. Centos7 修改SSH端口，以及修改密码
  20. 用python写了个全国疫情中高风险地区查询

热门文章

  1. unicode exp学习
  2. JAVA静态代码审查之checkstyle
  3. lsmod ‘used by‘ 的值是 -1
  4. 程序员找工作时的技巧
  5. 【案例回顾】春节一次较波折的MySQL调优
  6. ibooks打开iframe引用的html文件乱码
  7. 做个小推广-风景优美的旅游胜地
  8. 基于物联网的智慧农业解决方案
  9. NoSQLRedis的介绍和Redis安装部署，通过yum在线安装Redis，通过源码安装Redis；
  10. 什么软件可以修改服务器数据,恢复是服务器数据有什么软件好？