Tina R329 swupdate OTA升级步骤
2024-05-10 11:14:38
第一步：
编译路径执行make menucinfig和make ota_menucinfig中分别选中：
（1）Allwinner > swupdate
（2）Allwinner > swupdate > Swupdate Settings > General Configuration > MTD support
（3）Allwinner > swupdate > Image Handlers > ubivol
（4）Allwinner > swupdate > Image Handlers > allwinner boot0/uboot选上
第二步：
sys_config.fex中的storage_type 参数改成5（spi nand）
diff --git a/configs/evb5/sys_config.fex b/configs/evb5/sys_config.fex
index e168eb2..076e56d 100755
--- a/configs/evb5/sys_config.fex
+++ b/configs/evb5/sys_config.fex
-23,7 +23,7 eraseflag = 0
;----------------------------------------------------------------------------------
[target]
boot_clock = 1008
-storage_type = -1
+storage_type = 5
第三步：
编译路径执行 make -j & pack编译主系统并打包，此时会生成文件out/r329-evb5/tina_r329-evb5_uart0.img
第四步：
编译路径执行swupdate_make_recovery_img 编译OTA系统
此时会生成文件out/r329-evb5/boot_initramfs_recovery.img
第五步：
编译路径执行swupdate_pack_swu，此时会生成文件out/r329-evb5/swupdate/tina-r329-evb5.swu
第六步：
烧写主系统img，再把OTA文件推到设备下：adb push tina-r329-evb5.swu /mnt/UDISK/.
实际产品的时候就从网络拿到OTA文件即可
第八步：
OTA升级，设备端执行：
swupdate_cmd.sh -i /mnt/UDISK/tina-r329-evb5.swu -e stable,upgrade_recovery
执行后设备会重启并在重启过程中OTA，附log:
root@TinaLinux:/rom/sbin# swupdate_cmd.sh -i /mnt/UDISK/tina-r329-evb5.swu -e st
able,upgrade_recovery
config new swupdate
swu_input: ##-i /mnt/UDISK/tina-r329-evb5.swu -e stable,upgrade_recovery##
## set swupdate_param done ##
swu_param: ##-i /mnt/UDISK/tina-r329-evb5.swu##
swu_software: ##stable##
swu_mode: ##upgrade_recovery##
###now do swupdate###
###log in /mnt/UDISK/swupdate.log###
## swupdate -v -i /mnt/UDISK/tina-r329-evb5.swu -e stable,upgrade_recovery ##
Connected to SWUpdate via /tmp/swupdateprog Update started !
Interface: UNKNOWN [ ====================[ 3915.722335] sunxi-spinand: uboot blk range [8-32)% (ub)
==------------------------------[ 3915.730216] sunxi-spinand: download uboot toK
[ 3915.998351] sunxi-spinand: download uboot to block 15 (7 blocks) len 832K (u)
[ 3916.263272] sunxi-spinand: download uboot to block 22 (7 blocks) len 832K
[ =======================[ 3916.549016] sunxi-spinand: download boot0 to block K
[ 3916.567814] sunxi-spinand: download boot0 to block 1 len 32K
[ 3916.585825] sunxi-spinand: download boot0 to block 2 len 32K
[ 3916.603835] sunxi-spinand: download boot0 to block 3 len 32K
[ 3916.621752] sunxi-spinand: download boot0 to block 4 len 32K
[ 3916.639660] sunxi-spinand: download boot0 to block 5 len 32K
[ 3916.657647] sunxi-spinand: download boot0 to block 6 len 32K
[ 3916.675506] sunxi-spinand: download boot0 to block 7 len 32K
[ ============================================================ ] 5 of 5 100% (b)SUCCESS !
[ ============================================================ ] 5 of 5 100% (b)
DONE.
Connection closing..
Trying to connect to SWUpdate...
swu_next: ##reboot##
[ 3917.405486] [alarmtimer] have no shutdown alarm! alarmtimer_shutdown 322
[ 3917.819258] [LCD_FB] lcd_fb_gpio_set_value,line:353:
[ 3917.824652] OSAL_GPIO_DevWRITE_ONEPIN_DATA, hdl is NULL
[ 3917.875264] [LCD_FB] lcd_fb_shutdown,line:89:
[ 3917.879990] Finish
[ 3917.882539] sunxi_ohci_hcd_shutdown, ohci0-controller is disable, need not sn
[ 3917.891118] sunxi_ehci_hcd_shutdown, ehci0-controller is disable, need not sn
[ 3917.899769] reboot: Restarting system
[37]HELLO! BOOT0 is starting!
[40]BOOT0 commit : 4fb7c48
[43]set pll start
[45]periph0 has been enabled
[48]set pll end
[49]board init ok
[51]rtc[3] value = 0xa102
[54]the chip id is 0x2
[56]the chip id is 0x2
[58]the chip id is 0x2
[60]the chip id is 0x2
[62]the chip id is 0x2
[65]chip id check OK
[68][AUTO DEBUG] two rank and full DQ!
[71][AUTO DEBUG] DDR3 try success
[75][AUTO DEBUG] single rank and full DQ!
[80][AUTO DEBUG] rank 0 row = 13
[83][AUTO DEBUG] rank 0 bank = 8
[86][AUTO DEBUG] rank 0 page size = 2 KB
[90]DRAM BOOT DRIVE INFO: V0.15
[93]DRAM Type = 3 (2:DDR2,3:DDR3)
[96]DRAMC read ODT off.
[99]DRAM ODT off.
[101]DRAM CLK = 774 MHz
[104]DRAM SIZE =128 M
[109]DRAM simple test OK.
[111]dram size =128
[114]spinand UBOOT_START_BLK_NUM 8 UBOOT_LAST_BLK_NUM 32
[119]block from 8 to 32
[432]Check is correct.
[435]dma 0x107e20 int is not used yet
[438]dma 0x107e20 int is free, you do not need to free it again
[445]Entry_name = u-boot
[451]Entry_name = monitor
[454]Entry_name = dtb
[458]Jump to second Boot.
NOTICE: BL3-1: v1.0(debug):3eba4b6
NOTICE: BL3-1: Built : 10:18:25, 2020-05-21
NOTICE: BL3-1 commit: 8
ERROR: Error initializing runtime service tspd_fast
NOTICE: BL3-1: Preparing for EL3 exit to normal world
NOTICE: BL3-1: Next image address = 0x43000000
�OTICE: BL3-1: Next image spsr = 0x1d3 U-Boot 2018.05-gc7e08b9035 (May 28 2020 - 10:07:28 +0000) Allwinner Technology [00.513]CPU: Allwinner Family
[00.516]Model: sun50iw11
I2C: ready
[00.638]DRAM: 128 MiB
[00.641]Relocation Offset is: 04f01000
[00.664]secure enable bit: 0
[00.666]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=0Mhz
[00.677]gic: sec monitor mode
[00.680]flash init start
[00.682]workmode = 0,storage type = 0
[00.692]sunxi-spinand-phy: not detect any munufacture from id table
[00.699]sunxi-spinand-phy: get spi-nand Model from fdt fail
[00.704]sunxi-spinand-phy: get phy info from fdt fail
[00.710]sunxi flash init ok device nand0 <nand>, # parts = 5 #: name size offset mask_flags 0: boot0 0x00100000 0x00000000 1 1: uboot 0x00300000 0x00100000 1 2: secure_storage 0x00100000 0x00400000 1 3: pstore 0x00080000 0x00500000 1 4: sys 0x07a80000 0x00580000 0 active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000 defaults:
mtdids : nand0=nand
mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(s)
[00.840]ubi0: attaching mtd5
[00.950]ubi0: scanning is finished
[00.957]ubi0: attached mtd5 (name "sys", size 122 MiB)
[00.961]ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes
[00.967]ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048
[00.974]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[00.980]ubi0: good PEBs: 489, bad PEBs: 1, corrupted PEBs: 0
[00.985]ubi0: user volume: 12, internal volumes: 1, max. volumes count: 128
[00.992]ubi0: max/mean erase counter: 6/2, WL threshold: 4096, image sequence n0
[01.000]ubi0: available PEBs: 0, total reserved PEBs: 489, PEBs reserved for ba9
[01.009]Loading Environment from SUNXI_FLASH... OK
[01.089]Item0 (Map) magic is bad
[01.091]usb burn from boot
delay time 0
weak:otg_phy_config
[01.104]usb prepare ok
[01.322]usb sof ok
[01.324]usb probe ok
[01.326]usb setup ok
set address 0x2f
set address 0x2f ok
try to update
[04.331]do_burn_from_boot usb : have no handshake
[04.335]bmp_name=bootlogo.bmp
307254 bytes read in 17 ms (17.2 MiB/s)
[04.384]update dts
[04.386]update bootcmd
Hit any key to stop autoboot: 0
DSP VERSION IS v0.0.6_ymf_audio_head-19-gf485af9
DSP0 booting from 0x100400...
Android's image name: r329-evb5
[05.367]Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.191 (kunyao@Exdroid78) (gcc version 6.4.1 (Ope0
[ 0.000000] Boot CPU: AArch64 Processor [410fd034]
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] disp reserve base 0x46b43d40 ,size 0x4b036
[ 0.000000] cma: Reserved 24 MiB at 0x0000000045000000
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] DMA zone: 512 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 32768 pages, LIFO batch:7
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] psci: SMC Calling Convention v1.0
[ 0.000000] percpu: Embedded 21 pages/cpu s46104 r8192 d31720 u86016
[ 0.000000] pcpu-alloc: s46104 r8192 d31720 u86016 alloc=21*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pa6
[ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 initcall_
[ 0.000000] PID hash table entries: 512 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.000000] Memory: 81000K/131072K available (5438K kernel code, 470K rwdata)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 )
[ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 )
[ 0.000000] .text : 0xffffff8008080000 - 0xffffff80085d0000 ( 5440 )
[ 0.000000] .rodata : 0xffffff80085d0000 - 0xffffff8008760000 ( 1600 )
[ 0.000000] .init : 0xffffff8008760000 - 0xffffff8008c90000 ( 5312 )
[ 0.000000] .data : 0xffffff8008c90000 - 0xffffff8008d05808 ( 471 )
[ 0.000000] .bss : 0xffffff8008d05808 - 0xffffff8008d3a7dc ( 212 )
[ 0.000000] fixed : 0xffffffbefe7fb000 - 0xffffffbefec00000 ( 4116 )
[ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 )
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc008000000 ( 128 )
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] clk r_dsp_cache0 not found in of_sunxi_periph_cpus_clk_setup
[ 0.000000] clk r_dsp_cache1 not found in of_sunxi_periph_cpus_clk_setup
[ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, maxs
[ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (v.
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycless
[ 0.000004] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398s
[ 0.008121] Console: colour dummy device 80x25
[ 0.012413] Calibrating delay loop (skipped), value calculated using timer f)
[ 0.022619] pid_max: default: 32768 minimum: 301
[ 0.027373] Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
[ 0.033723] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes)
[ 0.041511] sched-energy: CPU device node has no sched-energy-costs
[ 0.046923] Invalid sched_group_energy for CPU0
[ 0.051402] CPU0: update cpu_capacity 1024
[ 0.067521] ASID allocator initialised with 32768 entries
[ 0.123755] Detected VIPT I-cache on CPU1
[ 0.123805] Invalid sched_group_energy for CPU1
[ 0.123808] CPU1: update cpu_capacity 1024
[ 0.123811] CPU1: Booted secondary processor [410fd034]
[ 0.123896] Brought up 2 CPUs
[ 0.138998] SMP: Total of 2 processors activated.
[ 0.143688] CPU features: detected feature: 32-bit EL0 Support
[ 0.149493] CPU features: detected feature: Kernel page table isolation (KPT)
[ 0.158798] CPU: All CPU(s) started at EL1
[ 0.160770] alternatives: patching kernel code
[ 0.165329] Invalid sched_group_energy for CPU1
[ 0.169689] Invalid sched_group_energy for Cluster1
[ 0.174539] Invalid sched_group_energy for CPU0
[ 0.179046] Invalid sched_group_energy for Cluster0
[ 0.184381] devtmpfs: initialized
[ 0.209914] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ms
[ 0.214042] futex hash table entries: 512 (order: 4, 65536 bytes)
[ 0.221064] atomic64_test: passed
[ 0.223372] pinctrl core: initialized pinctrl subsystem
[ 0.229539] NET: Registered protocol family 16
[ 0.234125] dump_class_init,857, success
[ 0.249127] cpuidle: using governor menu
[ 0.249604] vdso: 2 pages (1 code @ ffffff80085d6000, 1 data @ ffffff8008c94)
[ 0.255931] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.266984] sun50iw11p1-r-pinctrl r_pio: initialized sunXi PIO driver
[ 0.275539] sun50iw11p1-pinctrl pio: initialized sunXi PIO driver
[ 0.322079] pwm module init!
[ 0.325755] sunxi-pm debug v3.10
[ 0.326628] SCSI subsystem initialized
[ 0.327457] usbcore: registered new interface driver usbfs
[ 0.332775] usbcore: registered new interface driver hub
[ 0.337932] usbcore: registered new device driver usb
[ 0.343050] sunxi_i2c_adap_init()2552 - init
[ 0.347638] sunxi_i2c_probe()2289 - [i2c2] twi_drv_used = 1
[ 0.352678] sunxi_i2c_probe()2293 - [i2c2] twi_pkt_interval = 0
[ 0.358574] twi2 supply twi not found, using dummy regulator
[ 0.364273] twi_request_gpio()455 - [i2c2] init name: twi2
[ 0.370300] axp20x-i2c 2-0034: AXP20x variant AXP2585 found
[ 0.376991] sunxi_i2c_drv_core_process()1009 - [i2c2] Timeout when sending 9k
[ 0.383104] i2c_sunxi_drv_complete()1183 - [i2c2] incomplete xfer(status: 0x)
[ 0.391668] 0x07081600: 01011001 00000001 00006900 00010001
[ 0.397292] 0x07081610: 00008040 00010004 00010010 00000001
[ 0.402934] axp20x-i2c 2-0034: Failed to set masks in 0x40: -70
[ 0.408819] axp20x-i2c 2-0034: failed to add irq chip: -70
[ 0.414412] axp20x-i2c: probe of 2-0034 failed with error -70
[ 0.420031] sunxi_i2c_dma_request()1125 - [i2c2] using dma0chan0 (tx) and dms
[ 0.429989] sunxi_i2c_probe()2289 - [i2c1] twi_drv_used = 0
[ 0.435081] sunxi_i2c_probe()2293 - [i2c1] twi_pkt_interval = 0
[ 0.440983] twi1 supply twi not found, using dummy regulator
[ 0.446670] twi_request_gpio()455 - [i2c1] init name: twi1
[ 0.453814] ion_parse_dt_heap_common: id 0 type 0 name sys_user align 1000
[ 0.459125] ion_parse_dt_heap_common: id 4 type 4 name cma align 1000
[ 0.465493] ion_parse_dt_heap_common: id 6 type 6 name secure align 1000
[ 0.472290] ion_heap_create: Invalid heap type 6
[ 0.479872] Advanced Linux Sound Architecture Driver Initialized.
[ 0.483318] Bluetooth: Core ver 2.22
[ 0.486254] NET: Registered protocol family 31
[ 0.490653] Bluetooth: HCI device and connection manager initialized
[ 0.496967] Bluetooth: HCI socket layer initialized
[ 0.501820] Bluetooth: L2CAP socket layer initialized
[ 0.506898] Bluetooth: SCO socket layer initialized
[ 0.513216] input: sunxi-keyboard as /devices/virtual/input/input0
[ 0.522320] clocksource: Switched to clocksource arch_sys_counter
[ 0.535347] get androidboot.mode fail
[ 0.536042] NET: Registered protocol family 2
[ 0.538222] TCP established hash table entries: 16 (order: -5, 128 bytes)
[ 0.544578] TCP bind hash table entries: 16 (order: -4, 256 bytes)
[ 0.550639] TCP: Hash tables configured (established 16 bind 16)
[ 0.556673] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.562672] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.568908] NET: Registered protocol family 1
[ 0.573623] sunxi_spi_probe()2638 - [spi0] SPI MASTER MODE
[ 0.578551] spi0 supply spi not found, using dummy regulator
[ 0.584186] sunxi_spi_request_gpio()2248 - [spi0] Pinctrl init spi0
[ 0.590394] sunxi_spi_clk_init()2298 - [spi0] mclk 100000000
[ 0.596387] spi spi0: master is unqueued, this is deprecated
[ 0.601885] sunxi_spi_probe()2719 - [spi0]: driver probe succeed, base fffff6
[ 0.610871] sunxi_spi_probe()2629 - [spi1] SPI DBI INTERFACE
[ 0.615989] sunxi_spi_probe()2638 - [spi1] SPI MASTER MODE
[ 0.621524] spi1 supply spi not found, using dummy regulator
[ 0.627140] sunxi_spi_request_gpio()2248 - [spi1] Pinctrl init spi1
[ 0.633414] sunxi_spi_clk_init()2298 - [spi1] mclk 100000000
[ 0.639356] spi spi1: master is unqueued, this is deprecated
[ 0.644613] sunxi_spi_probe()2719 - [spi1]: driver probe succeed, base fffff7
[ 2.683876] workingset: timestamp_bits=61 max_order=15 bucket_order=0
[ 2.691998] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.695078] io scheduler noop registered
[ 2.696097] io scheduler deadline registered
[ 2.700860] io scheduler cfq registered (default)
[ 2.706603] [LCD_FB] lcd_fb_init,line:159:
[ 2.708922]
[ 2.710808] [LCD_FB] lcd_fb_probe,line:65:
[ 2.714488]
[ 2.735352] [LCD_FB] lcd_fb_script_get_item,line:139:
[ 2.735397] of_find_compatible_node allwinner,sunxi-lcd_fb1 fail
[ 2.740988] [LCD_FB] disp_lcd_set_panel_funs,line:1068:
[ 2.745787] lcd_panel_fun[0].cfg_panel_info is NULL
[ 2.754786] [LCD_FB] disp_lcd_spi_init,line:817:
[ 2.755222] Init spi1:bits_per_word:8 max_speed_hz:60000��Ё 2.765942] uartd
[ 2.765959] uart0 supply uart not found, using dummy regulator
[ 2.766151] uart0: ttyS0 at MMIO 0x2500000 (irq = 242, base_baud = 1500000) I
[ 2.766168] sw_console_setup()1823 - console setup baud 115200 parity n bitsn[ 2.786505] OSAL_GPIO_DevWRITE_ONEPIN_DATA, hdl is NULL
[ 2.786505] OSAL_GPIO_DevWRITE_ONEPIN_DATA, hdl is NULL
[ 2.798522] console [ttyS0] enabled
[ 2.798522] console [ttyS0] enabled
[ 2.807584] bootconsole [earlycon0] disabled
[ 2.807584] bootconsole [earlycon0] disabled
[ 2.816639] uart uart1: get regulator failed
[ 2.824881] uart1 supply uart not found, using dummy regulator
[ 2.831676] uart1: ttyS1 at MMIO 0x2500400 (irq = 243, base_baud = 1500000) I
[ 2.841435] misc dump reg init
[ 2.845177] Unable to detect cache hierarchy for CPU 0
[ 2.851243] sunxi-bt soc@03000000:bt: bt_power_num (4294967232)
[ 2.857912] sunxi-bt soc@03000000:bt: Missing bt_io_regulator.
[ 2.864473] sunxi-bt soc@03000000:bt: io_regulator_name ((null))
[ 2.871232] sunxi-bt soc@03000000:bt: request pincrtl handle for device [socd
[ 2.881152] sunxi-bt soc@03000000:bt: bt_rst gpio=386 mul-sel=1 pull=1 dr0
[ 2.890337] [LCD_FB] lcd_fb_gpio_set_value,line:353:
[ 2.890337] OSAL_GPIO_DevWRITE_ONEPIN_DATA, hdl is NULL
[ 2.902204] sunxi-bt soc@03000000:bt: clk_name ()
[ 2.907538] sunxi-bt soc@03000000:bt: clk not config
[ 2.913672] sunxi-wlan soc@03000000:wlan: wlan_busnum (1)
[ 2.919762] sunxi-wlan soc@03000000:wlan: wlan_power_num (-1)
[ 2.926230] sunxi-wlan soc@03000000:wlan: Missing wlan_io_regulator.
[ 2.933376] sunxi-wlan soc@03000000:wlan: io_regulator_name ((null))
[ 2.940530] sunxi-wlan soc@03000000:wlan: request pincrtl handle for device d
[ 2.951035] sunxi-wlan soc@03000000:wlan: wlan_regon gpio=384 mul-sel=1 pu0
[ 2.961615] sunxi-wlan soc@03000000:wlan: get gpio chip_en failed
[ 2.968478] sunxi-wlan soc@03000000:wlan: wlan_hostwake gpio=388 mul-sel=6 0
[ 2.979414] sunxi-wlan soc@03000000:wlan: clk_name ()
[ 2.985444] =====axp led init.====
[ 2.990350] sunxi-spinand: AW SPINand MTD Layer Version: 1.6 20200407
[ 2.994361] [LCD_FB] lcd_fb_gpio_set_value,line:353:
[ 2.994362] OSAL_GPIO_DevWRITE_ONEPIN_DATA, hdl is NULL
[ 3.009034] sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.10 20200306
[ 3.016958] sunxi-spinand-phy: not detect any munufacture from id table
[ 3.024395] sunxi-spinand-phy: get spi-nand Model from fdt fail
[ 3.031051] sunxi-spinand-phy: get phy info from fdt fail
[ 3.037116] sunxi-spinand-phy: not detect munufacture from fdt
[ 3.043833] sunxi-spinand-phy: detect munufacture from id table: GD
[ 3.050891] sunxi-spinand-phy: detect spinand id: ffffd1c8 ffffffff
[ 3.057947] sunxi-spinand-phy: ========== arch info ==========
[ 3.064512] sunxi-spinand-phy: Model: GD5F1GQ4UBYIG
[ 3.071369] sunxi-spinand-phy: Munufacture: GD
[ 3.077149] sunxi-spinand-phy: DieCntPerChip: 1
[ 3.082834] sunxi-spinand-phy: BlkCntPerDie: 1024
[ 3.088809] sunxi-spinand-phy: PageCntPerBlk: 64
[ 3.094591] sunxi-spinand-phy: SectCntPerPage: 4
[ 3.100273] sunxi-spinand-phy: OobSizePerPage: 64
[ 3.106056] sunxi-spinand-phy: BadBlockFlag: 0x0
[ 3.111937] sunxi-spinand-phy: OperationOpt: 0x7
[ 3.117818] sunxi-spinand-phy: MaxEraseTimes: 50000
[ 3.123888] sunxi-spinand-phy: EccFlag: 0x1
[ 3.129769] sunxi-spinand-phy: EccType: 7
[ 3.135451] sunxi-spinand-phy: EccProtectedType: 4
[ 3.141134] sunxi-spinand-phy: ========================================
[ 3.148570] sunxi-spinand-phy:
[ 3.152105] sunxi-spinand-phy: ========== physical info ==========
[ 3.159057] sunxi-spinand-phy: TotalSize: 128 M
[ 3.164446] sunxi-spinand-phy: SectorSize: 512 B
[ 3.169837] sunxi-spinand-phy: PageSize: 2 K
[ 3.175032] sunxi-spinand-phy: BlockSize: 128 K
[ 3.180422] sunxi-spinand-phy: OOBSize: 64 B
[ 3.185715] sunxi-spinand-phy: ========================================
[ 3.193153] sunxi-spinand-phy:
[ 3.196694] sunxi-spinand-phy: ========== logical info ==========
[ 3.203546] sunxi-spinand-phy: TotalSize: 128 M
[ 3.208937] sunxi-spinand-phy: SectorSize: 512 B
[ 3.214329] sunxi-spinand-phy: PageSize: 4 K
[ 3.219525] sunxi-spinand-phy: BlockSize: 256 K
[ 3.224915] sunxi-spinand-phy: OOBSize: 128 B
[ 3.230303] sunxi-spinand-phy: ========================================
[ 3.238343] sunxi-spinand-phy: block lock register: 0x00
[ 3.244900] sunxi-spinand-phy: feature register: 0x11
[ 3.250584] sunxi-spinand-phy: sunxi physic nand init end
[ 3.256968] Creating 5 MTD partitions on "sunxi_mtd_nand":
[ 3.263143] 0x000000000000-0x000000100000 : "boot0"
[ 3.270597] 0x000000100000-0x000000400000 : "uboot"
[ 3.277651] random: fast init done
[ 3.284611] 0x000000400000-0x000000500000 : "secure_storage"
[ 3.292732] 0x000000500000-0x000000580000 : "pstore"
[ 3.299618] pstore_zone: registered pstore_blk as backend for kmsg(Oops,pani)
[ 3.308394] pstore: Registered pstore_blk as persistent store backend
[ 3.315645] mtd mtd3: Attached to MTD device 3
[ 3.320667] 0x000000580000-0x000008000000 : "sys"
[ 3.505411] sunxi-spinand-phy: phy blk 1023 is bad
[ 3.511632] libphy: Fixed MDIO Bus: probed
[ 3.517334] gmac-power0: NULL
[ 3.520700] gmac-power1: NULL
[ 3.524039] gmac-power2: NULL
[ 3.528328] Failed to alloc md5
[ 3.531884] eth0: Use random mac address
[ 3.536483] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.544061] get ehci0-controller, regulator_io is no nocare
[ 3.550329] get ehci0-controller wakeup-source is fail.
[ 3.556375] sunxi ehci0-controller don't init wakeup source
[ 3.562648] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunx9
[ 3.576220] [sunxi-ehci0]: Not init ehci0
[ 3.581050] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.588233] get ohci0-controller, regulator_io is no nocare
[ 3.594504] get ohci0-controller wakeup-source is fail.
[ 3.600520] sunxi ohci0-controller don't init wakeup source
[ 3.606862] [sunxi-ohci0]: probe, pdev->name: 4101000.ohci0-controller, sunx0
[ 3.617317] [sunxi-ohci0]: Not init ohci0
[ 3.621919] get ohci1-controller, regulator_io is no nocare
[ 3.628182] get ohci1-controller wakeup-source is fail.
[ 3.634155] sunxi ohci1-controller don't init wakeup source
[ 3.640481] [sunxi-ohci1]: probe, pdev->name: 4201000.ohci1-controller, sunx0
[ 3.650959] 4201000.ohci1-controller supply drvvbus not found, using dummy rr
[ 3.659796] sunxi-ohci 4201000.ohci1-controller: SW USB2.0 'Open' Host Contrr
[ 3.669598] sunxi-ohci 4201000.ohci1-controller: new USB bus registered, ass1
[ 3.679348] sunxi-ohci 4201000.ohci1-controller: irq 252, io mem 0x00000040
[ 3.751307] hub 1-0:1.0: USB hub found
[ 3.755572] hub 1-0:1.0: 1 port detected
[ 3.760815] usbcore: registered new interface driver uas
[ 3.766901] usbcore: registered new interface driver usb-storage
[ 3.773711] usbcore: registered new interface driver ums-alauda
[ 3.780422] usbcore: registered new interface driver ums-cypress
[ 3.787227] usbcore: registered new interface driver ums-datafab
[ 3.794025] usbcore: registered new interface driver ums_eneub6250
[ 3.801022] usbcore: registered new interface driver ums-freecom
[ 3.807823] usbcore: registered new interface driver ums-isd200
[ 3.814531] usbcore: registered new interface driver ums-jumpshot
[ 3.821428] usbcore: registered new interface driver ums-karma
[ 3.828038] usbcore: registered new interface driver ums-onetouch
[ 3.834965] usbcore: registered new interface driver ums-realtek
[ 3.841778] usbcore: registered new interface driver ums-sddr09
[ 3.848484] usbcore: registered new interface driver ums-sddr55
[ 3.855182] usbcore: registered new interface driver ums-usbat
[ 3.861842] usb_serial_number:20080411
[ 3.867078] sunxi_gpadc_init,1831, success
[ 3.872667] sunxi-rtc rtc: rtc core: registered sunxi-rtc as rtc0
[ 3.879593] sunxi-rtc rtc: RTC enabled
[ 3.884139] i2c /dev entries driver
[ 3.888603] lirc_dev: IR Remote Control driver registered, major 249
[ 3.895763] IR NEC protocol handler initialized
[ 3.900856] IR RC5(x/sz) protocol handler initialized
[ 3.906537] IR LIRC bridge handler initialized
[ 3.911699] sun50iw11p1-r-pinctrl r_pio: expect_func as:s_cir0, but muxsel(2r
[ 3.921284] sunxi_ir_startup: get ir protocol failed
[ 3.926686] s_cir_rx supply ir0 not found, using dummy regulator
[ 3.933760] Registered IR keymap rc_map_sunxi
[ 3.939015] input: sunxi-ir as /devices/platform/soc/s_cir_rx/rc/rc0/input1
[ 3.947059] rc rc0: sunxi-ir as /devices/platform/soc/s_cir_rx/rc/rc0
[ 3.954715] rc rc0: lirc_dev: driver ir-lirc-codec (sunxi-rc-recv) registere0
[ 3.964617] sun50iw11p1-pinctrl pio: expect_func as:ir0, but muxsel(2) is fur
[ 3.973160] sunxi_ir_tx_probe()629 - sunxi-ir-tx v1.0.0
[ 3.979068] sunxi_ir_tx_startup()602 - base: ffffff8008f45000 !
[ 3.985821] sunxi_ir_tx_startup()609 - irq num: 245 !
[ 3.991585] Registered IR keymap rc_map_sunxi
[ 3.996830] input: sunxi-ir-tx as /devices/platform/soc/ir_tx/rc/rc1/ir_tx
[ 4.004767] rc rc1: sunxi-ir-tx as /devices/platform/soc/ir_tx/rc/rc1
[ 4.012278] rc rc1: lirc_dev: driver ir-lirc-codec (sunxi-ir-tx) registered 1
[ 4.021384] sunxi_ir_tx_probe()680 - register rc device success
[ 4.028051] ir_tx_clk_cfg()336 - get ir parent rate 24000000HZ
[ 4.034627] ir_tx_clk_cfg()345 - get ir_clk rate 12000000HZ
[ 4.040897] sunxi_ir_tx_probe()690 - ir_tx_setup success
[ 4.046918] sunxi_ir_tx_probe()700 - request irq success
[ 4.052890] sunxi_ir_tx_probe()701 - probe success
[ 4.058591] sunxi cedar version 0.1
[ 4.062812] google_vp9: sunxi google vp9 version 0.1
[ 4.070246] sunxi-wdt 20000a0.watchdog: Watchdog enabled (timeout=16 sec, no)
[ 4.079385] Bluetooth: HCI UART driver ver 2.2.d448471.20181218-163903
[ 4.086736] Bluetooth: HCI UART protocol H4 registered
[ 4.092513] Bluetooth: HCI H4 protocol initialized
[ 4.097902] Bluetooth: HCI UART protocol (null) registered
[ 4.104072] Bluetooth: HCI Realtek H5 protocol initialized
[ 4.112143] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 1008000z
[ 4.123867] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changez
[ 4.139403] sunxi-mmc sdc0: SD/MMC/SDIO Host Controller Driver(v3.45 2020-5-)
[ 4.148312] sunxi-mmc sdc0: ***ctl-spec-caps*** 8
[ 4.153608] sunxi-mmc sdc0: No vmmc regulator found
[ 4.159053] sunxi-mmc sdc0: No vqmmc regulator found
[ 4.164593] sunxi-mmc sdc0: No vdmmc regulator found
[ 4.170140] sunxi-mmc sdc0: No vd33sw regulator found
[ 4.175775] sunxi-mmc sdc0: No vd18sw regulator found
[ 4.181407] sunxi-mmc sdc0: No vq33sw regulator found
[ 4.187043] sunxi-mmc sdc0: No vq18sw regulator found
[ 4.193203] sunxi-mmc sdc0: set host busy
[ 4.197761] sunxi-mmc sdc0: Got CD GPIO
[ 4.202301] sunxi-mmc sdc0: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 tB
[ 4.212519] sunxi-mmc sdc0: no vqmmc,Check if there is regulator
[ 4.238334] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 widtB
[ 4.266727] sunxi-mmc sdc0: detmode:gpio irq
[ 4.266757] sunxi-mmc sdc0: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 tB
[ 4.283171] sunxi-mmc sdc1: SD/MMC/SDIO Host Controller Driver(v3.45 2020-5-)
[ 4.292068] sunxi-mmc sdc1: No vmmc regulator found
[ 4.297514] sunxi-mmc sdc1: No vqmmc regulator found
[ 4.303057] sunxi-mmc sdc1: No vdmmc regulator found
[ 4.308595] sunxi-mmc sdc1: No vd33sw regulator found
[ 4.314231] sunxi-mmc sdc1: No vd18sw regulator found
[ 4.319866] sunxi-mmc sdc1: No vq33sw regulator found
[ 4.325496] sunxi-mmc sdc1: No vq18sw regulator found
[ 4.331731] sunxi-mmc sdc1: set host busy
[ 4.336319] mmc:failed to get gpios
[ 4.340394] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 tB
[ 4.350618] sunxi-mmc sdc1: no vqmmc,Check if there is regulator
[ 4.374382] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 widtB
[ 4.402515] sunxi-mmc sdc1: detmode:manually by software
[ 4.408843] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 widtB
[ 4.419985] sunxi_led_probe()1690 - start
[ 4.420018] sunxi_get_str_of_property()1549 - failed to get the string of pr!
[ 4.421136] sunxi_led_probe()1782 - finish
[ 4.421550] usbcore: registered new interface driver usbhid
[ 4.421553] usbhid: USB HID core driver
[ 4.422300] [KMD INFO] AIPU KMD Init Start...
[ 4.422303] [KMD INFO] KMD version: release 1.1.0
[ 4.422305] [KMD INFO] AIPU version: zhouyi v1
[ 4.422345] [KMD INFO] AIPU config: default.
[ 4.422350] [KMD INFO] get platform resource name /aipu@0x03050000,irq 272 .
[ 4.422351] [KMD INFO] platform_get_resource ok!
[ 4.426943] [KMD INFO] create AIPU core ok!
[ 4.436969] [KMD INFO] DMA alloc coherent failed: size = 0x2600000, try to a.
[ 4.447330] [KMD INFO] KMD request reserved CMA successfully: base 0x4520000.
[ 4.447427] [KMD INFO] set aipu clock ok!
[ 4.447434] [KMD INFO] AIPU Initial Status: 0x70000.
[ 4.447437] [KMD INFO] AIPU_CTRL_REG_OFFSET 0x0: 0x2
[ 4.447439] [KMD INFO] AIPU_START_PC_REG_OFFSET 0x8: 0x0
[ 4.447442] [KMD INFO] AIPU_INTR_PC_REG_OFFSET 0xc: 0x10
[ 4.447444] [KMD INFO] AIPU_IPI_CTRL_REG_OFFSET 0x10: 0x0
[ 4.447447] [KMD INFO] AIPU_DATA_ADDR_0_REG_OFFSET 0x14 : 0xfadeeef1
[ 4.447450] [KMD INFO] AIPU_DATA_ADDR_1_REG_OFFSET 0x18 : 0x79247fff
[ 4.447452] [KMD INFO] AIPU_CLK_CTRL_REG_OFFSET 0x3c: 0x0
[ 4.447454] [KMD INFO] AIPU KMD probe done.
[ 4.453437] sunxi-daudio daudio1: regulator missing or invalid
[ 4.453662] sunxi-daudio daudio2: regulator missing or invalid
[ 4.454034] rpmsg_hifi 3003000.msgbox0.sunxi,dsp0.0.-1: id:sunxi,dsp0 new ch!
[ 4.460350] rpmsg_hifi 3003000.msgbox0.sunxi,dsp0.0.-1: rpmsg hifi[0] clientd
[ 4.460418] rpmsg_hifi 3008000.msgbox1.sunxi,dsp1.0.-1: id:sunxi,dsp1 new ch!
[ 4.464753] rpmsg_hifi 3008000.msgbox1.sunxi,dsp1.0.-1: rpmsg hifi[1] clientd
[ 4.475924] sunxi-internal-cpudai cpudai: dmaengine alloc coherent phy_addr:0
[ 4.476142] sunxi-internal-cpudai cpudai: dmaengine alloc coherent phy_addr:0
[ 4.476148] sunxi-internal-cpudai cpudai: sunxi_hifi_cpudai_probe start.
[ 4.504750] sunxi-internal-cpudai cpudai: sunxi_hifi_cpudai_probe stop.
[ 4.504758] sunxi-codec-machine sndcodec: sunxi_hifi_sndcodec_init
[ 4.505228] sunxi-codec-machine sndcodec: sunxi-hifi-codec <-> cpudai mappink
[ 4.506877] sunxi-rpaf-dsp sunxi_rpaf_dsp0: register device finished!
[ 4.506882] sunxi-rpaf-dsp sunxi_rpaf_dsp0: [rpaf_dsp0] probe finished!
[ 4.507029] sunxi-rpaf-dsp sunxi_rpaf_dsp1: register device finished!
[ 4.507033] sunxi-rpaf-dsp sunxi_rpaf_dsp1: [rpaf_dsp1] probe finished!
[ 4.507837] NET: Registered protocol family 10
[ 4.512886] NET: Registered protocol family 17
[ 4.513099] Bluetooth: RFCOMM TTY layer initialized
[ 4.513109] Bluetooth: RFCOMM socket layer initialized
[ 4.513131] Bluetooth: RFCOMM ver 1.11
[ 4.513140] 8021q: 802.1Q VLAN Support v1.8
[ 4.521823] ubi0: attaching mtd4
[ 4.748295] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 widtB
[ 4.760956] sunxi-mmc sdc1: smc 1 p1 err, cmd 8, RTO !!
[ 4.767133] sunxi-mmc sdc1: card claims to support voltages below defined rae
[ 4.785006] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 widtB
[ 4.795694] sunxi-mmc sdc1: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 wiB
[ 4.806627] sunxi-mmc sdc1: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 wiB
[ 4.818426] mmc1: new high speed SDIO card at address 0001
[ 4.992811] random: crng init done
[ 5.042975] ubi0: scanning is finished
[ 5.055825] ubi0: attached mtd4 (name "sys", size 122 MiB)
[ 5.062016] ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes
[ 5.069699] ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048
[ 5.077278] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.085052] ubi0: good PEBs: 489, bad PEBs: 1, corrupted PEBs: 0
[ 5.091751] ubi0: user volume: 12, internal volumes: 1, max. volumes count: 8
[ 5.099906] ubi0: max/mean erase counter: 6/2, WL threshold: 4096, image seq0
[ 5.109219] ubi0: available PEBs: 0, total reserved PEBs: 489, PEBs reserved9
[ 5.119585] ubi0: background thread "ubi_bgt0d" started, PID 798
[ 5.131004] block ubiblock0_5: created from ubi0:5(rootfs)
[ 5.137384] get usb_detect_mode is fail, 22
[ 5.142567] sunxi-rtc rtc: setting system clock to 1970-01-01 01:15:25 UTC ()
[ 5.151869] snddaudio snddaudio1: codec: snd-soc-dummy, codec_dai: snd-soc-d.
[ 5.161165] snddaudio snddaudio1: snd-soc-dummy-dai <-> daudio1 mapping ok
[ 5.169687] snddaudio snddaudio2: codec: snd-soc-dummy, codec_dai: snd-soc-d.
[ 5.179198] snddaudio snddaudio2: snd-soc-dummy-dai <-> daudio2 mapping ok
[ 5.188138] ALSA device list:
[ 5.191468] #0: audiocodec
[ 5.194683] #1: snddaudio1
[ 5.197888] #2: snddaudio2
[ 5.204794] Freeing unused kernel memory: 5312K
[ 5.224604] init: Console is alive
[ 5.228622] init: - watchdog -
[ 5.232107] init: - preinit -
/dev/by-name/UDISK already format by ubifs
/dev/by-name/rootfs_data not exist
[ 5.352763] UBIFS (ubi0:11): background thread "ubifs_bgt0_11" started, PID 9
[ 5.420546] UBIFS (ubi0:11): recovery needed
[ 5.639621] UBIFS (ubi0:11): recovery completed
[ 5.644945] UBIFS (ubi0:11): UBIFS: mounted UBI device 0, volume 11, name "U"
[ 5.653319] UBIFS (ubi0:11): LEB size: 258048 bytes (252 KiB), min./max. I/Os
[ 5.664491] UBIFS (ubi0:11): FS size: 56770560 bytes (54 MiB, 220 LEBs), jou)
[ 5.676247] UBIFS (ubi0:11): reserved for root: 0 bytes (0 KiB)
[ 5.682863] UBIFS (ubi0:11): media format: w4/r0 (latest is w4/r0), UUID AF3l
[ 5.715680] procd: - early -
[ 5.719024] procd: - watchdog -
[ 5.859254] procd: - watchdog -
[ 5.863025] procd: - ubus -
[ 5.866699] procd (1): /proc/1045/oom_adj is deprecated, please use /proc/10.
[ 5.917282] procd: - init -
Please press Enter to activate this console.
[ 6.086076] file system registered
[ 6.105873] configfs-gadget 4100000.udc-controller: failed to start g1: -19
[ 6.162533] read descriptors
[ 6.165757] read strings
[ 6.211401] sunxi-wlan soc@03000000:wlan: bus_index: 1
Trying to connect to SWUpdate...
Connected to SWUpdate via /tmp/swupdateprog
[ 8.215807] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 8.486345]
[ 8.486345] insmod_device_driver
[ 8.486345]
[ 8.898403] sunxi_set_cur_vol_work()408 WARN: get power supply failed
[ 8.976988] android_work: sent uevent USB_STATE=CONNECTED
[ 8.983214] sunxi_set_cur_vol_work()408 WARN: get power supply failed
[ 9.079460] configfs-gadget gadget: high-speed config #1: c
[ 9.085831] android_work: sent uevent USB_STATE=CONFIGURED Update started !
Interface: UNKNOWN [ ============================================================ ] 4 of 4 100% (d)SUCCESS !
[ ============================================================ ] 4 of 4 100% (d)
DONE.
Connection closing..
Trying to connect to SWUpdate...
Connected to SWUpdate via /tmp/swupdateprog
[ ------------------------------------------------------------ ] 0 of 0 0% () SUCCESS !
[ ------------------------------------------------------------ ] 0 of 0 0% ()
DONE.
Connection closing..
Trying to connect to SWUpdate...
[ 29.915562] [alarmtimer] have no shutdown alarm! alarmtimer_shutdown 322
[ 30.178336] [LCD_FB] lcd_fb_gpio_set_value,line:353:
[ 30.183699] OSAL_GPIO_DevWRITE_ONEPIN_DATA, hdl is NULL
[ 30.234423] [LCD_FB] lcd_fb_shutdown,line:89:
[ 30.239106] Finish
[ 30.241692] sunxi_ohci_hcd_shutdown, ohci0-controller is disable, need not sn
[ 30.250246] sunxi_ehci_hcd_shutdown, ehci0-controller is disable, need not sn
[ 30.258910] reboot: Restarting system
[37]HELLO! BOOT0 is starting!
[40]BOOT0 commit : 4fb7c48
[43]set pll start
[45]periph0 has been enabled
[48]set pll end
[49]board init ok
[51]rtc[3] value = 0xa102
[54]the chip id is 0x2
[56]the chip id is 0x2
[58]the chip id is 0x2
[60]the chip id is 0x2
[62]the chip id is 0x2
[65]chip id check OK
[67][AUTO DEBUG] two rank and full DQ!
[71][AUTO DEBUG] DDR3 try success
[75][AUTO DEBUG] single rank and full DQ!
[80][AUTO DEBUG] rank 0 row = 13
[83][AUTO DEBUG] rank 0 bank = 8
[86][AUTO DEBUG] rank 0 page size = 2 KB
[90]DRAM BOOT DRIVE INFO: V0.15
[93]DRAM Type = 3 (2:DDR2,3:DDR3)
[96]DRAMC read ODT off.
[99]DRAM ODT off.
[101]DRAM CLK = 774 MHz
[104]DRAM SIZE =128 M
[109]DRAM simple test OK.
[111]dram size =128
[114]spinand UBOOT_START_BLK_NUM 8 UBOOT_LAST_BLK_NUM 32
[119]block from 8 to 32
[433]Check is correct.
[435]dma 0x107e20 int is not used yet
[439]dma 0x107e20 int is free, you do not need to free it again
[445]Entry_name = u-boot
[451]Entry_name = monitor
[455]Entry_name = dtb
[458]Jump to second Boot.
NOTICE: BL3-1: v1.0(debug):3eba4b6
NOTICE: BL3-1: Built : 10:18:25, 2020-05-21
NOTICE: BL3-1 commit: 8
ERROR: Error initializing runtime service tspd_fast
NOTICE: BL3-1: Preparing for EL3 exit to normal world
NOTICE: BL3-1: Next image address = 0x43000000
�OTICE: BL3-1: Next image spsr = 0x1d3 U-Boot 2018.05-gc7e08b9035 (May 28 2020 - 10:07:28 +0000) Allwinner Technology [00.513]CPU: Allwinner Family
[00.516]Model: sun50iw11
I2C: ready
[00.639]DRAM: 128 MiB
[00.641]Relocation Offset is: 04f01000
[00.664]secure enable bit: 0
[00.666]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=0Mhz
[00.677]gic: sec monitor mode
[00.680]flash init start
[00.682]workmode = 0,storage type = 0
[00.692]sunxi-spinand-phy: not detect any munufacture from id table
[00.699]sunxi-spinand-phy: get spi-nand Model from fdt fail
[00.704]sunxi-spinand-phy: get phy info from fdt fail
[00.710]sunxi flash init ok device nand0 <nand>, # parts = 5 #: name size offset mask_flags 0: boot0 0x00100000 0x00000000 1 1: uboot 0x00300000 0x00100000 1 2: secure_storage 0x00100000 0x00400000 1 3: pstore 0x00080000 0x00500000 1 4: sys 0x07a80000 0x00580000 0 active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000 defaults:
mtdids : nand0=nand
mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(s)
[00.841]ubi0: attaching mtd5
[00.950]ubi0: scanning is finished
[00.957]ubi0: attached mtd5 (name "sys", size 122 MiB)
[00.961]ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes
[00.968]ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048
[00.974]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[00.980]ubi0: good PEBs: 489, bad PEBs: 1, corrupted PEBs: 0
[00.986]ubi0: user volume: 12, internal volumes: 1, max. volumes count: 128
[00.992]ubi0: max/mean erase counter: 6/3, WL threshold: 4096, image sequence n0
[01.000]ubi0: available PEBs: 0, total reserved PEBs: 489, PEBs reserved for ba9
[01.009]Loading Environment from SUNXI_FLASH... OK
[01.089]Item0 (Map) magic is bad
[01.092]usb burn from boot
delay time 0
weak:otg_phy_config
[01.104]usb prepare ok
[01.411]usb sof ok
[01.412]usb probe ok
[01.414]usb setup ok
set address 0x32
set address 0x32 ok
try to update
[04.420]do_burn_from_boot usb : have no handshake
[04.424]bmp_name=bootlogo.bmp
307254 bytes read in 17 ms (17.2 MiB/s)
[04.473]update dts
[04.475]update bootcmd
Hit any key to stop autoboot: 0
DSP VERSION IS v0.0.6_ymf_audio_head-19-gf485af9
DSP0 booting from 0x100400...
Android's image name: r329-evb5
[05.099]Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.191 (kunyao@Exdroid78) (gcc version 6.4.1 (Ope0
[ 0.000000] Boot CPU: AArch64 Processor [410fd034]
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] disp reserve base 0x46b43d40 ,size 0x4b036
[ 0.000000] cma: Reserved 24 MiB at 0x0000000045000000
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] DMA zone: 512 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 32768 pages, LIFO batch:7
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] psci: SMC Calling Convention v1.0
[ 0.000000] percpu: Embedded 21 pages/cpu s46104 r8192 d31720 u86016
[ 0.000000] pcpu-alloc: s46104 r8192 d31720 u86016 alloc=21*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pa6
[ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 initcall_
[ 0.000000] PID hash table entries: 512 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.000000] Memory: 85928K/131072K available (5438K kernel code, 470K rwdata)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 )
[ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 )
[ 0.000000] .text : 0xffffff8008080000 - 0xffffff80085d0000 ( 5440 )
[ 0.000000] .rodata : 0xffffff80085d0000 - 0xffffff8008760000 ( 1600 )
[ 0.000000] .init : 0xffffff8008760000 - 0xffffff80087c0000 ( 384 )
[ 0.000000] .data : 0xffffff80087c0000 - 0xffffff8008835808 ( 471 )
[ 0.000000] .bss : 0xffffff8008835808 - 0xffffff800886aa5c ( 213 )
[ 0.000000] fixed : 0xffffffbefe7fb000 - 0xffffffbefec00000 ( 4116 )
[ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 )
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc008000000 ( 128 )
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] clk r_dsp_cache0 not found in of_sunxi_periph_cpus_clk_setup
[ 0.000000] clk r_dsp_cache1 not found in of_sunxi_periph_cpus_clk_setup
[ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, maxs
[ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (v.
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycless
[ 0.000004] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398s
[ 0.008122] Console: colour dummy device 80x25
[ 0.012412] Calibrating delay loop (skipped), value calculated using timer f)
[ 0.022618] pid_max: default: 32768 minimum: 301
[ 0.027374] Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
[ 0.033722] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes)
[ 0.041504] sched-energy: CPU device node has no sched-energy-costs
[ 0.046922] Invalid sched_group_energy for CPU0
[ 0.051401] CPU0: update cpu_capacity 1024
[ 0.067521] ASID allocator initialised with 32768 entries
[ 0.123754] Detected VIPT I-cache on CPU1
[ 0.123804] Invalid sched_group_energy for CPU1
[ 0.123807] CPU1: update cpu_capacity 1024
[ 0.123810] CPU1: Booted secondary processor [410fd034]
[ 0.123894] Brought up 2 CPUs
[ 0.138997] SMP: Total of 2 processors activated.
[ 0.143687] CPU features: detected feature: 32-bit EL0 Support
[ 0.149492] CPU features: detected feature: Kernel page table isolation (KPT)
[ 0.158781] CPU: All CPU(s) started at EL1
[ 0.160769] alternatives: patching kernel code
[ 0.165326] Invalid sched_group_energy for CPU1
[ 0.169689] Invalid sched_group_energy for Cluster1
[ 0.174538] Invalid sched_group_energy for CPU0
[ 0.179045] Invalid sched_group_energy for Cluster0
[ 0.184371] devtmpfs: initialized
[ 0.210303] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ms
[ 0.214433] futex hash table entries: 512 (order: 4, 65536 bytes)
[ 0.221483] atomic64_test: passed
[ 0.223760] pinctrl core: initialized pinctrl subsystem
[ 0.229929] NET: Registered protocol family 16
[ 0.234517] dump_class_init,857, success
[ 0.253520] cpuidle: using governor menu
[ 0.254004] vdso: 2 pages (1 code @ ffffff80085d6000, 1 data @ ffffff80087c4)
[ 0.260326] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.271406] sun50iw11p1-r-pinctrl r_pio: initialized sunXi PIO driver
[ 0.280001] sun50iw11p1-pinctrl pio: initialized sunXi PIO driver
[ 0.329922] pwm module init!
[ 0.333525] sunxi-pm debug v3.10
[ 0.334356] SCSI subsystem initialized
[ 0.335174] usbcore: registered new interface driver usbfs
[ 0.340475] usbcore: registered new interface driver hub
[ 0.345702] usbcore: registered new device driver usb
[ 0.350784] sunxi_i2c_adap_init()2552 - init
[ 0.355350] sunxi_i2c_probe()2289 - [i2c2] twi_drv_used = 1
[ 0.360435] sunxi_i2c_probe()2293 - [i2c2] twi_pkt_interval = 0
[ 0.366332] twi2 supply twi not found, using dummy regulator
[ 0.372014] twi_request_gpio()455 - [i2c2] init name: twi2
[ 0.378017] axp20x-i2c 2-0034: AXP20x variant AXP2585 found
[ 0.384769] sunxi_i2c_drv_core_process()1009 - [i2c2] Timeout when sending 9k
[ 0.390852] i2c_sunxi_drv_complete()1183 - [i2c2] incomplete xfer(status: 0x)
[ 0.399433] 0x07081600: 01011001 00000001 00006900 00010001
[ 0.405064] 0x07081610: 00008040 00010004 00010010 00000001
[ 0.410698] axp20x-i2c 2-0034: Failed to set masks in 0x40: -70
[ 0.416591] axp20x-i2c 2-0034: failed to add irq chip: -70
[ 0.422178] axp20x-i2c: probe of 2-0034 failed with error -70
[ 0.427805] sunxi_i2c_dma_request()1125 - [i2c2] using dma0chan0 (tx) and dms
[ 0.437751] sunxi_i2c_probe()2289 - [i2c1] twi_drv_used = 0
[ 0.442856] sunxi_i2c_probe()2293 - [i2c1] twi_pkt_interval = 0
[ 0.448754] twi1 supply twi not found, using dummy regulator
[ 0.454437] twi_request_gpio()455 - [i2c1] init name: twi1
[ 0.461506] ion_parse_dt_heap_common: id 0 type 0 name sys_user align 1000
[ 0.466906] ion_parse_dt_heap_common: id 4 type 4 name cma align 1000
[ 0.473261] ion_parse_dt_heap_common: id 6 type 6 name secure align 1000
[ 0.480036] ion_heap_create: Invalid heap type 6
[ 0.487628] Advanced Linux Sound Architecture Driver Initialized.
[ 0.491171] Bluetooth: Core ver 2.22
[ 0.494021] NET: Registered protocol family 31
[ 0.498412] Bluetooth: HCI device and connection manager initialized
[ 0.504743] Bluetooth: HCI socket layer initialized
[ 0.509587] Bluetooth: L2CAP socket layer initialized
[ 0.514645] Bluetooth: SCO socket layer initialized
[ 0.521070] input: sunxi-keyboard as /devices/virtual/input/input0
[ 0.530076] clocksource: Switched to clocksource arch_sys_counter
[ 0.543040] get androidboot.mode fail
[ 0.543720] NET: Registered protocol family 2
[ 0.545959] TCP established hash table entries: 16 (order: -5, 128 bytes)
[ 0.552234] TCP bind hash table entries: 16 (order: -4, 256 bytes)
[ 0.558338] TCP: Hash tables configured (established 16 bind 16)
[ 0.564371] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.570134] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.576601] NET: Registered protocol family 1
[ 0.581307] sunxi_spi_probe()2638 - [spi0] SPI MASTER MODE
[ 0.586236] spi0 supply spi not found, using dummy regulator
[ 0.591859] sunxi_spi_request_gpio()2248 - [spi0] Pinctrl init spi0
[ 0.598098] sunxi_spi_clk_init()2298 - [spi0] mclk 100000000
[ 0.604093] spi spi0: master is unqueued, this is deprecated
[ 0.609590] sunxi_spi_probe()2719 - [spi0]: driver probe succeed, base fffff6
[ 0.618572] sunxi_spi_probe()2629 - [spi1] SPI DBI INTERFACE
[ 0.623686] sunxi_spi_probe()2638 - [spi1] SPI MASTER MODE
[ 0.629210] spi1 supply spi not found, using dummy regulator
[ 0.634838] sunxi_spi_request_gpio()2248 - [spi1] Pinctrl init spi1
[ 0.641101] sunxi_spi_clk_init()2298 - [spi1] mclk 100000000
[ 0.647053] spi spi1: master is unqueued, this is deprecated
[ 0.652299] sunxi_spi_probe()2719 - [spi1]: driver probe succeed, base fffff7
[ 0.663412] workingset: timestamp_bits=61 max_order=15 bucket_order=0
[ 0.674810] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.677605] io scheduler noop registered
[ 0.678952] io scheduler deadline registered
[ 0.683535] io scheduler cfq registered (default)
[ 0.689081] [LCD_FB] lcd_fb_init,line:159:
[ 0.691845]
[ 0.693610] [LCD_FB] lcd_fb_probe,line:65:
[ 0.697307]
[ 0.719346] [LCD_FB] lcd_fb_script_get_item,line:139:
[ 0.719389] of_find_compatible_node allwinner,sunxi-lcd_fb1 fail
[ 0.724980] [LCD_FB] disp_lcd_set_panel_funs,line:1068:
[ 0.729795] lcd_panel_fun[0].cfg_panel_info is NULL
[ 0.738763] [LCD_FB] disp_lcd_spi_init,line:817:
[ 0.739214] Init spi1:bits_per_word:8 �U�}م텱�Օ�line:353:[ 0.748400] uartd
[ 0.748415] uart0 supply uart not found, using dummy regulator
[ 0.748605] uart0: ttyS0 at MMIO 0x2500000 (irq = 242, base_baud = 1500000) I
[ 0.748625] sw_console_setup()1823 - console setup baud 115200 parity n bitsn[ 0.770517] OSAL_GPIO_DevWRITE_ONEPIN_DATA, hdl is NULL
[ 0.770517] OSAL_GPIO_DevWRITE_ONEPIN_DATA, hdl is NULL
[ 0.782433] console [ttyS0] enabled
[ 0.782433] console [ttyS0] enabled
[ 0.791769] bootconsole [earlycon0] disabled
[ 0.791769] bootconsole [earlycon0] disabled
[ 0.800564] uart uart1: get regulator failed
[ 0.808801] uart1 supply uart not found, using dummy regulator
[ 0.815609] uart1: ttyS1 at MMIO 0x2500400 (irq = 243, base_baud = 1500000) I
[ 0.825354] misc dump reg init
[ 0.829080] Unable to detect cache hierarchy for CPU 0
[ 0.835150] sunxi-bt soc@03000000:bt: bt_power_num (4294967232)
[ 0.841812] sunxi-bt soc@03000000:bt: Missing bt_io_regulator.
[ 0.848375] sunxi-bt soc@03000000:bt: io_regulator_name ((null))
[ 0.855138] sunxi-bt soc@03000000:bt: request pincrtl handle for device [socd
[ 0.865063] sunxi-bt soc@03000000:bt: bt_rst gpio=386 mul-sel=1 pull=1 dr0
[ 0.874668] sunxi-bt soc@03000000:bt: clk_name ()
[ 0.878094] [LCD_FB] lcd_fb_gpio_set_value,line:353:
[ 0.878095] OSAL_GPIO_DevWRITE_ONEPIN_DATA, hdl is NULL
[ 0.891446] sunxi-bt soc@03000000:bt: clk not config
[ 0.897580] sunxi-wlan soc@03000000:wlan: wlan_busnum (1)
[ 0.903672] sunxi-wlan soc@03000000:wlan: wlan_power_num (-1)
[ 0.910139] sunxi-wlan soc@03000000:wlan: Missing wlan_io_regulator.
[ 0.917284] sunxi-wlan soc@03000000:wlan: io_regulator_name ((null))
[ 0.924439] sunxi-wlan soc@03000000:wlan: request pincrtl handle for device d
[ 0.934943] sunxi-wlan soc@03000000:wlan: wlan_regon gpio=384 mul-sel=1 pu0
[ 0.945524] sunxi-wlan soc@03000000:wlan: get gpio chip_en failed
[ 0.952387] sunxi-wlan soc@03000000:wlan: wlan_hostwake gpio=388 mul-sel=6 0
[ 0.963321] sunxi-wlan soc@03000000:wlan: clk_name ()
[ 0.969355] =====axp led init.====
[ 0.974251] sunxi-spinand: AW SPINand MTD Layer Version: 1.6 20200407
[ 0.978125] [LCD_FB] lcd_fb_gpio_set_value,line:353:
[ 0.978126] OSAL_GPIO_DevWRITE_ONEPIN_DATA, hdl is NULL
[ 0.992953] sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.10 20200306
[ 1.000862] sunxi-spinand-phy: not detect any munufacture from id table
[ 1.008321] sunxi-spinand-phy: get spi-nand Model from fdt fail
[ 1.014974] sunxi-spinand-phy: get phy info from fdt fail
[ 1.021040] sunxi-spinand-phy: not detect munufacture from fdt
[ 1.027749] sunxi-spinand-phy: detect munufacture from id table: GD
[ 1.034808] sunxi-spinand-phy: detect spinand id: ffffd1c8 ffffffff
[ 1.041838] sunxi-spinand-phy: ========== arch info ==========
[ 1.048399] sunxi-spinand-phy: Model: GD5F1GQ4UBYIG
[ 1.055243] sunxi-spinand-phy: Munufacture: GD
[ 1.061019] sunxi-spinand-phy: DieCntPerChip: 1
[ 1.066693] sunxi-spinand-phy: BlkCntPerDie: 1024
[ 1.072660] sunxi-spinand-phy: PageCntPerBlk: 64
[ 1.078433] sunxi-spinand-phy: SectCntPerPage: 4
[ 1.084108] sunxi-spinand-phy: OobSizePerPage: 64
[ 1.089883] sunxi-spinand-phy: BadBlockFlag: 0x0
[ 1.095754] sunxi-spinand-phy: OperationOpt: 0x7
[ 1.101625] sunxi-spinand-phy: MaxEraseTimes: 50000
[ 1.107690] sunxi-spinand-phy: EccFlag: 0x1
[ 1.113559] sunxi-spinand-phy: EccType: 7
[ 1.119234] sunxi-spinand-phy: EccProtectedType: 4
[ 1.124908] sunxi-spinand-phy: ========================================
[ 1.132337] sunxi-spinand-phy:
[ 1.135866] sunxi-spinand-phy: ========== physical info ==========
[ 1.142808] sunxi-spinand-phy: TotalSize: 128 M
[ 1.148189] sunxi-spinand-phy: SectorSize: 512 B
[ 1.153577] sunxi-spinand-phy: PageSize: 2 K
[ 1.158763] sunxi-spinand-phy: BlockSize: 128 K
[ 1.164147] sunxi-spinand-phy: OOBSize: 64 B
[ 1.169429] sunxi-spinand-phy: ========================================
[ 1.176856] sunxi-spinand-phy:
[ 1.180386] sunxi-spinand-phy: ========== logical info ==========
[ 1.187230] sunxi-spinand-phy: TotalSize: 128 M
[ 1.192612] sunxi-spinand-phy: SectorSize: 512 B
[ 1.197994] sunxi-spinand-phy: PageSize: 4 K
[ 1.203181] sunxi-spinand-phy: BlockSize: 256 K
[ 1.208564] sunxi-spinand-phy: OOBSize: 128 B
[ 1.213947] sunxi-spinand-phy: ========================================
[ 1.221485] sunxi-spinand-phy: block lock register: 0x00
[ 1.227619] sunxi-spinand-phy: feature register: 0x11
[ 1.233306] sunxi-spinand-phy: sunxi physic nand init end
[ 1.240065] Creating 5 MTD partitions on "sunxi_mtd_nand":
[ 1.246248] 0x000000000000-0x000000100000 : "boot0"
[ 1.253827] 0x000000100000-0x000000400000 : "uboot"
[ 1.260029] random: fast init done
[ 1.268346] 0x000000400000-0x000000500000 : "secure_storage"
[ 1.276649] 0x000000500000-0x000000580000 : "pstore"
[ 1.283619] pstore_zone: registered pstore_blk as backend for kmsg(Oops,pani)
[ 1.292392] pstore: Registered pstore_blk as persistent store backend
[ 1.299642] mtd mtd3: Attached to MTD device 3
[ 1.304657] 0x000000580000-0x000008000000 : "sys"
[ 1.495169] sunxi-spinand-phy: phy blk 1023 is bad
[ 1.501370] libphy: Fixed MDIO Bus: probed
[ 1.507095] gmac-power0: NULL
[ 1.510447] gmac-power1: NULL
[ 1.513774] gmac-power2: NULL
[ 1.518106] Failed to alloc md5
[ 1.521638] eth0: Use random mac address
[ 1.526254] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.533833] get ehci0-controller, regulator_io is no nocare
[ 1.540112] get ehci0-controller wakeup-source is fail.
[ 1.546165] sunxi ehci0-controller don't init wakeup source
[ 1.552437] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunx9
[ 1.566013] [sunxi-ehci0]: Not init ehci0
[ 1.570851] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.578024] get ohci0-controller, regulator_io is no nocare
[ 1.584300] get ohci0-controller wakeup-source is fail.
[ 1.590320] sunxi ohci0-controller don't init wakeup source
[ 1.596666] [sunxi-ohci0]: probe, pdev->name: 4101000.ohci0-controller, sunx0
[ 1.607120] [sunxi-ohci0]: Not init ohci0
[ 1.611722] get ohci1-controller, regulator_io is no nocare
[ 1.617986] get ohci1-controller wakeup-source is fail.
[ 1.623959] sunxi ohci1-controller don't init wakeup source
[ 1.630287] [sunxi-ohci1]: probe, pdev->name: 4201000.ohci1-controller, sunx0
[ 1.640759] 4201000.ohci1-controller supply drvvbus not found, using dummy rr
[ 1.649607] sunxi-ohci 4201000.ohci1-controller: SW USB2.0 'Open' Host Contrr
[ 1.659405] sunxi-ohci 4201000.ohci1-controller: new USB bus registered, ass1
[ 1.669149] sunxi-ohci 4201000.ohci1-controller: irq 252, io mem 0x00000040
[ 1.739068] hub 1-0:1.0: USB hub found
[ 1.743328] hub 1-0:1.0: 1 port detected
[ 1.748589] usbcore: registered new interface driver uas
[ 1.754686] usbcore: registered new interface driver usb-storage
[ 1.761495] usbcore: registered new interface driver ums-alauda
[ 1.768198] usbcore: registered new interface driver ums-cypress
[ 1.775002] usbcore: registered new interface driver ums-datafab
[ 1.781809] usbcore: registered new interface driver ums_eneub6250
[ 1.788805] usbcore: registered new interface driver ums-freecom
[ 1.795605] usbcore: registered new interface driver ums-isd200
[ 1.802310] usbcore: registered new interface driver ums-jumpshot
[ 1.809205] usbcore: registered new interface driver ums-karma
[ 1.815813] usbcore: registered new interface driver ums-onetouch
[ 1.822730] usbcore: registered new interface driver ums-realtek
[ 1.829536] usbcore: registered new interface driver ums-sddr09
[ 1.836245] usbcore: registered new interface driver ums-sddr55
[ 1.842953] usbcore: registered new interface driver ums-usbat
[ 1.849611] usb_serial_number:20080411
[ 1.854857] sunxi_gpadc_init,1831, success
[ 1.860447] sunxi-rtc rtc: rtc core: registered sunxi-rtc as rtc0
[ 1.867371] sunxi-rtc rtc: RTC enabled
[ 1.871921] i2c /dev entries driver
[ 1.876393] lirc_dev: IR Remote Control driver registered, major 249
[ 1.883549] IR NEC protocol handler initialized
[ 1.888643] IR RC5(x/sz) protocol handler initialized
[ 1.894324] IR LIRC bridge handler initialized
[ 1.899509] sun50iw11p1-r-pinctrl r_pio: expect_func as:s_cir0, but muxsel(2r
[ 1.909084] sunxi_ir_startup: get ir protocol failed
[ 1.914487] s_cir_rx supply ir0 not found, using dummy regulator
[ 1.921568] Registered IR keymap rc_map_sunxi
[ 1.926812] input: sunxi-ir as /devices/platform/soc/s_cir_rx/rc/rc0/input1
[ 1.934855] rc rc0: sunxi-ir as /devices/platform/soc/s_cir_rx/rc/rc0
[ 1.942466] rc rc0: lirc_dev: driver ir-lirc-codec (sunxi-rc-recv) registere0
[ 1.952376] sun50iw11p1-pinctrl pio: expect_func as:ir0, but muxsel(2) is fur
[ 1.960922] sunxi_ir_tx_probe()629 - sunxi-ir-tx v1.0.0
[ 1.966830] sunxi_ir_tx_startup()602 - base: ffffff8008975000 !
[ 1.973586] sunxi_ir_tx_startup()609 - irq num: 245 !
[ 1.979346] Registered IR keymap rc_map_sunxi
[ 1.984605] input: sunxi-ir-tx as /devices/platform/soc/ir_tx/rc/rc1/ir_tx
[ 1.992537] rc rc1: sunxi-ir-tx as /devices/platform/soc/ir_tx/rc/rc1
[ 2.000032] rc rc1: lirc_dev: driver ir-lirc-codec (sunxi-ir-tx) registered 1
[ 2.009141] sunxi_ir_tx_probe()680 - register rc device success
[ 2.015804] ir_tx_clk_cfg()336 - get ir parent rate 24000000HZ
[ 2.022385] ir_tx_clk_cfg()345 - get ir_clk rate 12000000HZ
[ 2.028649] sunxi_ir_tx_probe()690 - ir_tx_setup success
[ 2.034676] sunxi_ir_tx_probe()700 - request irq success
[ 2.040646] sunxi_ir_tx_probe()701 - probe success
[ 2.046342] sunxi cedar version 0.1
[ 2.050578] google_vp9: sunxi google vp9 version 0.1
[ 2.058111] sunxi-wdt 20000a0.watchdog: Watchdog enabled (timeout=16 sec, no)
[ 2.067249] Bluetooth: HCI UART driver ver 2.2.d448471.20181218-163903
[ 2.074600] Bluetooth: HCI UART protocol H4 registered
[ 2.080385] Bluetooth: HCI H4 protocol initialized
[ 2.085773] Bluetooth: HCI UART protocol (null) registered
[ 2.091937] Bluetooth: HCI Realtek H5 protocol initialized
[ 2.100002] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 1008000z
[ 2.111751] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changez
[ 2.127304] sunxi-mmc sdc0: SD/MMC/SDIO Host Controller Driver(v3.45 2020-5-)
[ 2.136178] sunxi-mmc sdc0: ***ctl-spec-caps*** 8
[ 2.141485] sunxi-mmc sdc0: No vmmc regulator found
[ 2.146928] sunxi-mmc sdc0: No vqmmc regulator found
[ 2.152475] sunxi-mmc sdc0: No vdmmc regulator found
[ 2.158011] sunxi-mmc sdc0: No vd33sw regulator found
[ 2.163651] sunxi-mmc sdc0: No vd18sw regulator found
[ 2.169283] sunxi-mmc sdc0: No vq33sw regulator found
[ 2.174924] sunxi-mmc sdc0: No vq18sw regulator found
[ 2.180971] sunxi-mmc sdc0: set host busy
[ 2.185522] sunxi-mmc sdc0: Got CD GPIO
[ 2.190063] sunxi-mmc sdc0: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 tB
[ 2.200284] sunxi-mmc sdc0: no vqmmc,Check if there is regulator
[ 2.226090] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 widtB
[ 2.254483] sunxi-mmc sdc0: detmode:gpio irq
[ 2.254512] sunxi-mmc sdc0: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 tB
[ 2.270926] sunxi-mmc sdc1: SD/MMC/SDIO Host Controller Driver(v3.45 2020-5-)
[ 2.279819] sunxi-mmc sdc1: No vmmc regulator found
[ 2.285265] sunxi-mmc sdc1: No vqmmc regulator found
[ 2.290801] sunxi-mmc sdc1: No vdmmc regulator found
[ 2.296344] sunxi-mmc sdc1: No vd33sw regulator found
[ 2.301978] sunxi-mmc sdc1: No vd18sw regulator found
[ 2.307612] sunxi-mmc sdc1: No vq33sw regulator found
[ 2.313248] sunxi-mmc sdc1: No vq18sw regulator found
[ 2.319481] sunxi-mmc sdc1: set host busy
[ 2.324069] mmc:failed to get gpios
[ 2.328145] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 tB
[ 2.338366] sunxi-mmc sdc1: no vqmmc,Check if there is regulator
[ 2.362140] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 widtB
[ 2.390271] sunxi-mmc sdc1: detmode:manually by software
[ 2.396599] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 widtB
[ 2.407769] sunxi_led_probe()1690 - start
[ 2.407792] sunxi_get_str_of_property()1549 - failed to get the string of pr!
[ 2.408915] sunxi_led_probe()1782 - finish
[ 2.409201] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.409401] usbcore: registered new interface driver usbhid
[ 2.409404] usbhid: USB HID core driver
[ 2.410230] [KMD INFO] AIPU KMD Init Start...
[ 2.410234] [KMD INFO] KMD version: release 1.1.0
[ 2.410236] [KMD INFO] AIPU version: zhouyi v1
[ 2.410238] [KMD INFO] AIPU config: default.
[ 2.410242] [KMD INFO] get platform resource name /aipu@0x03050000,irq 272 .
[ 2.410244] [KMD INFO] platform_get_resource ok!
[ 2.414852] [KMD INFO] create AIPU core ok!
[ 2.424875] [KMD INFO] DMA alloc coherent failed: size = 0x2600000, try to a.
[ 2.435232] [KMD INFO] KMD request reserved CMA successfully: base 0x4520000.
[ 2.435324] [KMD INFO] set aipu clock ok!
[ 2.435332] [KMD INFO] AIPU Initial Status: 0x70000.
[ 2.435334] [KMD INFO] AIPU_CTRL_REG_OFFSET 0x0: 0x2
[ 2.435337] [KMD INFO] AIPU_START_PC_REG_OFFSET 0x8: 0x0
[ 2.435340] [KMD INFO] AIPU_INTR_PC_REG_OFFSET 0xc: 0x10
[ 2.435342] [KMD INFO] AIPU_IPI_CTRL_REG_OFFSET 0x10: 0x0
[ 2.435345] [KMD INFO] AIPU_DATA_ADDR_0_REG_OFFSET 0x14 : 0xfadeeef1
[ 2.435347] [KMD INFO] AIPU_DATA_ADDR_1_REG_OFFSET 0x18 : 0x79247fff
[ 2.435350] [KMD INFO] AIPU_CLK_CTRL_REG_OFFSET 0x3c: 0x0
[ 2.435352] [KMD INFO] AIPU KMD probe done.
[ 2.441342] sunxi-daudio daudio1: regulator missing or invalid
[ 2.441563] sunxi-daudio daudio2: regulator missing or invalid
[ 2.441949] rpmsg_hifi 3003000.msgbox0.sunxi,dsp0.0.-1: id:sunxi,dsp0 new ch!
[ 2.448077] rpmsg_hifi 3003000.msgbox0.sunxi,dsp0.0.-1: rpmsg hifi[0] clientd
[ 2.448142] rpmsg_hifi 3008000.msgbox1.sunxi,dsp1.0.-1: id:sunxi,dsp1 new ch!
[ 2.454406] rpmsg_hifi 3008000.msgbox1.sunxi,dsp1.0.-1: rpmsg hifi[1] clientd
[ 2.465243] sunxi-internal-cpudai cpudai: dmaengine alloc coherent phy_addr:0
[ 2.465437] sunxi-internal-cpudai cpudai: dmaengine alloc coherent phy_addr:0
[ 2.465443] sunxi-internal-cpudai cpudai: sunxi_hifi_cpudai_probe start.
[ 2.499342] sunxi-internal-cpudai cpudai: sunxi_hifi_cpudai_probe stop.
[ 2.499349] sunxi-codec-machine sndcodec: sunxi_hifi_sndcodec_init
[ 2.499804] sunxi-codec-machine sndcodec: sunxi-hifi-codec <-> cpudai mappink
[ 2.501167] sunxi-rpaf-dsp sunxi_rpaf_dsp0: register device finished!
[ 2.501172] sunxi-rpaf-dsp sunxi_rpaf_dsp0: [rpaf_dsp0] probe finished!
[ 2.501316] sunxi-rpaf-dsp sunxi_rpaf_dsp1: register device finished!
[ 2.501320] sunxi-rpaf-dsp sunxi_rpaf_dsp1: [rpaf_dsp1] probe finished!
[ 2.502191] NET: Registered protocol family 10
[ 2.507355] NET: Registered protocol family 17
[ 2.507573] Bluetooth: RFCOMM TTY layer initialized
[ 2.507584] Bluetooth: RFCOMM socket layer initialized
[ 2.507606] Bluetooth: RFCOMM ver 1.11
[ 2.507615] 8021q: 802.1Q VLAN Support v1.8
[ 2.516292] ubi0: attaching mtd4
[ 2.742821] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 widtB
[ 2.755461] sunxi-mmc sdc1: smc 1 p1 err, cmd 8, RTO !!
[ 2.761641] sunxi-mmc sdc1: card claims to support voltages below defined rae
[ 2.779515] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 widtB
[ 2.790213] sunxi-mmc sdc1: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 wiB
[ 2.801151] sunxi-mmc sdc1: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 wiB
[ 2.812871] mmc1: new high speed SDIO card at address 0001
[ 2.978848] random: crng init done
[ 3.038982] ubi0: scanning is finished
[ 3.051715] ubi0: attached mtd4 (name "sys", size 122 MiB)
[ 3.057852] ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes
[ 3.065524] ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048
[ 3.073101] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.080899] ubi0: good PEBs: 489, bad PEBs: 1, corrupted PEBs: 0
[ 3.087602] ubi0: user volume: 12, internal volumes: 1, max. volumes count: 8
[ 3.095755] ubi0: max/mean erase counter: 6/3, WL threshold: 4096, image seq0
[ 3.105080] ubi0: available PEBs: 0, total reserved PEBs: 489, PEBs reserved9
[ 3.115435] ubi0: background thread "ubi_bgt0d" started, PID 797
[ 3.126839] block ubiblock0_5: created from ubi0:5(rootfs)
[ 3.133219] get usb_detect_mode is fail, 22
[ 3.138401] sunxi-rtc rtc: setting system clock to 1970-01-01 01:15:59 UTC ()
[ 3.147710] snddaudio snddaudio1: codec: snd-soc-dummy, codec_dai: snd-soc-d.
[ 3.157017] snddaudio snddaudio1: snd-soc-dummy-dai <-> daudio1 mapping ok
[ 3.165551] snddaudio snddaudio2: codec: snd-soc-dummy, codec_dai: snd-soc-d.
[ 3.175080] snddaudio snddaudio2: snd-soc-dummy-dai <-> daudio2 mapping ok
[ 3.184040] ALSA device list:
[ 3.187375] #0: audiocodec
[ 3.190604] #1: snddaudio1
[ 3.193809] #2: snddaudio2
[ 3.199226] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 3.209670] devtmpfs: mounted
[ 3.213295] Freeing unused kernel memory: 384K
[ 3.721817] init: Console is alive
[ 3.725815] init: - watchdog -
[ 3.729299] init: - preinit -
/dev/by-name/UDISK already format by ubifs
[ 4.465916] mount_root: mounting /dev/root
[ 4.471835] mount_root: loading kmods from internal overlay
[ 4.613907] block: attempting to load /etc/config/fstab
[ 4.643170] UBIFS (ubi0:11): background thread "ubifs_bgt0_11" started, PID 1
[ 4.710779] UBIFS (ubi0:11): recovery needed
[ 4.928114] UBIFS (ubi0:11): recovery completed
[ 4.933362] UBIFS (ubi0:11): UBIFS: mounted UBI device 0, volume 11, name "U"
[ 4.941739] UBIFS (ubi0:11): LEB size: 258048 bytes (252 KiB), min./max. I/Os
[ 4.952918] UBIFS (ubi0:11): FS size: 56770560 bytes (54 MiB, 220 LEBs), jou)
[ 4.964668] UBIFS (ubi0:11): reserved for root: 0 bytes (0 KiB)
[ 4.971287] UBIFS (ubi0:11): media format: w4/r0 (latest is w4/r0), UUID AF3l
[ 4.987250] block: extroot: UUID match (root: 5c662140-a90edc37-17199d16-496)
[ 5.008486] mount_root: switched to extroot
[ 5.020295] procd: - early -
[ 5.023631] procd: - watchdog -
[ 5.226304] procd: - watchdog -
[ 5.229961] procd: - ubus -
[ 5.233606] procd (1): /proc/1056/oom_adj is deprecated, please use /proc/10.
[ 5.325631] procd: - init -
Please press Enter to activate this console.
[ 5.937362] file system registered
[ 6.046608] configfs-gadget 4100000.udc-controller: failed to start g1: -19
[ 6.221568] read descriptors
[ 6.224868] read strings
[ 6.304715] fuse init (API version 7.26)
[ 6.305929] sunxi-codec-machine sndcodec: sunxi_hifi_sndcodec_startup
[ 6.306261] sunxi-codec-machine sndcodec: sunxi_hifi_sndcodec_hw_params
[ 6.306269] sunxi-internal-cpudai cpudai: ======== hw_params ========
[ 6.306274] sunxi-internal-cpudai cpudai: pcm_params->format:2
[ 6.306278] sunxi-internal-cpudai cpudai: pcm_params->channels:2
[ 6.306283] sunxi-internal-cpudai cpudai: pcm_params->rate:48000
[ 6.306287] sunxi-internal-cpudai cpudai: pcm_params->period_size:1024
[ 6.306291] sunxi-internal-cpudai cpudai: pcm_params->periods:4
[ 6.306295] sunxi-internal-cpudai cpudai: pcm_params->pcm_frames:1024
[ 6.306299] sunxi-internal-cpudai cpudai: pcm_params->buffer_size:4096
[ 6.306303] sunxi-internal-cpudai cpudai: ===========================
[ 6.456842] sunxi-internal-cpudai cpudai: sunxi_hifi_pcm_hw_params
[ 6.494154]
[ 6.494154] insmod_device_driver
[ 6.494154]
[ 6.697590] sunxi-wlan soc@03000000:wlan: bus_index: 1
[ 6.946582] sunxi_set_cur_vol_work()408 WARN: get power supply failed
[ 7.025233] android_work: sent uevent USB_STATE=CONNECTED
[ 7.031295] sunxi_set_cur_vol_work()408 WARN: get power supply failed
[ 7.133113] configfs-gadget gadget: high-speed config #1: c
[ 7.139527] android_work: sent uevent USB_STATE=CONFIGURED
[ 8.012713] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 8.018858] Bluetooth: BNEP filters: protocol multicast
[ 8.024773] Bluetooth: BNEP socket layer initialized
[ 8.039175] usbcore: registered new interface driver btusb
[ 8.092344] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 8.099046] Bluetooth: HIDP socket layer initialized
[ 8.129967] tlsc6x_ts 1-002e: fail to get vdd_name
[ 8.135339] tlsc6x_ts 1-002e: fail to get virtualkeys
[ 8.141072] 1-002e supply vdd not found, using dummy regulator
[ 8.406667] sunxi_i2c_do_xfer()1942 - [i2c1] incomplete xfer (status: 0x20, )
[ 8.416030] [tlsc][error] [IIC]: i2c_transfer(1) error, addr= 0x0!!
[ 8.423088] [tlsc][error] [IIC]: i2c_transfer(1) error, ret=-70, rlen=3, wle!
[ 8.431912] sunxi_i2c_do_xfer()1942 - [i2c1] incomplete xfer (status: 0x20, )
[ 8.441308] [tlsc][error] [IIC]: i2c_transfer(1) error, addr= 0x0!!
[ 8.448308] [tlsc][error] [IIC]: i2c_transfer(1) error, ret=-70, rlen=3, wle!
[ 8.457103] sunxi_i2c_do_xfer()1942 - [i2c1] incomplete xfer (status: 0x20, )
[ 8.466505] [tlsc][error] [IIC]: i2c_transfer(1) error, addr= 0x0!!
[ 8.473503] [tlsc][error] [IIC]: i2c_transfer(1) error, ret=-70, rlen=3, wle!
[ 8.482110] sunxi_i2c_do_xfer()1942 - [i2c1] incomplete xfer (status: 0x20, )
[ 8.491454] [tlsc][error] [IIC]: i2c_transfer(1) error, addr= 0x0!!
[ 8.498448] [tlsc][error] [IIC]: i2c_transfer(1) error, ret=-70, rlen=3, wle!
[ 8.582628] sunxi_i2c_do_xfer()1942 - [i2c1] incomplete xfer (status: 0x20, )
[ 8.591991] [tlsc][error] [IIC]: i2c_transfer(1) error, addr= 0x0!!
[ 8.599032] [tlsc][error] [IIC]: i2c_transfer(1) error, ret=-70, rlen=3, wle!
[ 8.607828] sunxi_i2c_do_xfer()1942 - [i2c1] incomplete xfer (status: 0x20, )
[ 8.617200] [tlsc][error] [IIC]: i2c_transfer(1) error, addr= 0x0!!
[ 8.624228] [tlsc][error] [IIC]: i2c_transfer(1) error, ret=-70, rlen=3, wle!
[ 8.632911] sunxi_i2c_do_xfer()1942 - [i2c1] incomplete xfer (status: 0x20, )
[ 8.642319] [tlsc][error] [IIC]: i2c_transfer(1) error, addr= 0x0!!
[ 8.649326] [tlsc][error] [IIC]: i2c_transfer(1) error, ret=-70, rlen=3, wle!
[ 8.657956] sunxi_i2c_do_xfer()1942 - [i2c1] incomplete xfer (status: 0x20, )
[ 8.667302] [tlsc][error] [IIC]: i2c_transfer(1) error, addr= 0x0!!
[ 8.674291] [tlsc][error] [IIC]: i2c_transfer(1) error, ret=-70, rlen=3, wle!
[ 8.758347] sunxi_i2c_do_xfer()1942 - [i2c1] incomplete xfer (status: 0x20, )
[ 8.767685] [tlsc][error] [IIC]: i2c_transfer(1) error, addr= 0x0!!
[ 8.774675] [tlsc][error] [IIC]: i2c_transfer(1) error, ret=-70, rlen=3, wle!
[ 8.783533] sunxi_i2c_do_xfer()1942 - [i2c1] incomplete xfer (status: 0x20, )
[ 8.792889] [tlsc][error] [IIC]: i2c_transfer(1) error, addr= 0x0!!
[ 8.799923] [tlsc][error] [IIC]: i2c_transfer(1) error, ret=-70, rlen=3, wle!
[ 8.808502] sunxi_i2c_do_xfer()1942 - [i2c1] incomplete xfer (status: 0x20, )
[ 8.817829] [tlsc][error] [IIC]: i2c_transfer(1) error, addr= 0x0!!
[ 8.824824] [tlsc][error] [IIC]: i2c_transfer(1) error, ret=-70, rlen=3, wle!
[ 8.833347] sunxi_i2c_do_xfer()1942 - [i2c1] incomplete xfer (status: 0x20, )
[ 8.842686] [tlsc][error] [IIC]: i2c_transfer(1) error, addr= 0x0!!
[ 8.849693] [tlsc][error] [IIC]: i2c_transfer(1) error, ret=-70, rlen=3, wle!
[ 8.858076] [tlsc][error] tlsc6x:tlsc6x_probe, no tlsc6x!
Trying to connect to SWUpdate...
[ 9.867544] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 10.005688] libphy: 4500000.eth: probed
[ 10.130508] sunxi-gmac 4500000.eth eth0: eth0: Type(7) PHY ID 001cc916 at 0 )
[ 10.152285] br-lan: port 1(eth0) entered blocking state
[ 10.158185] br-lan: port 1(eth0) entered disabled state
[ 10.164288] device eth0 entered promiscuous mode
[ 10.170855] br-lan: port 1(eth0) entered blocking state
[ 10.176701] br-lan: port 1(eth0) entered forwarding state
[ 10.182897] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 10.890211] br-lan: port 1(eth0) entered disabled state
[ 14.197586] sunxi-internal-cpudai cpudai: sunxi_hifi_pcm_hw_free
[ 14.336895] sunxi-codec-machine sndcodec: sunxi_hifi_sndcodec_shutdown BusyBox v1.27.2 () built-in shell (ash) _____ _ __ _
|_ _||_| ___ _ _ | | |_| ___ _ _ _ _ | | _ | || | | |__ | || || | ||_'_| | | | || | || _ | |_____||_||_|_||___||_,_| |_| |_||_|_||_|_| Tina is Based on OpenWrt! ---------------------------------------------- Tina Linux (Neptune, 5C1C9C53) ----------------------------------------------
root@TinaLinux:/# Tina R329 swupdate OTA升级步骤相关推荐
- QCC30DFU流程android说明,qcc512x qcc302x qcc303x earbud 软件GAIA OTA DFU 空中升级实现方法以及升级步骤...
QCC512x QCC302x QCC303x earbud 软件GAIA OTA DFU 空中升级实现方法以及升级步骤 概述 OTA只能升级部分,不是所有的都可以OTA.如PSKEY区,蓝牙地址,蓝 ...
- 华为手机怎么ota升级鸿蒙,华为手机如何升级鸿蒙系统 步骤如下
华为鸿蒙OS系统的发布,让华为开启国产操作系统的替代之路,就在之前,华为鸿蒙OS系统再次传来了好消息,很多华为手机用户反馈,自己已经收到了华为推送的鸿蒙系统的短信,只需要根据华为官方发送到的提示,填写 ...
- OTA升级flash分区
什么是在线OTA升级 - OTA是Over-the-Air的简写,空中下载技术的意思. - OTA在线升级在日常消费电子产品中很常见,比如手机,机顶盒等,通过网络,下载 ...
- android ota 版本校验,OTA升级签名校验简析
1. 概要 如果进行过OTA升级的开发者,都或多或少有这样的疑问,如何确定该OTA升级包是可以信任的呢?这其中其实涉及到一个签名验证的流程. 2. 签名生成 在生成正规的固件时,一般会运行生成新key ...
- 【转】Android OTA 升级之一：编译升级包
Android OTA 升级之一:编译升级包 作者: 宋立新 Email : zjujoe@yahoo.com 前言 OTA 升级是 Android 系统提供的标准软件升级方式. 它功能强大,提供了完 ...
- 华为y220t android版本升级,华为 Y220T(移动版)救砖教程 救砖包 刷回官方系统支持OTA升级...
华为 Y220T (移动版)怎么救砖,华为 Y220T (移动版)救砖教程 ,简单给你的华为 Y220T (移动版)刷回官方系统,华为 Y220T (移动版)刷完官方线刷救砖包后即可正常OTA升级. ...
- OTA升级常见问题及流程
OTA升级 1.日志查看 2. SELinux权限QA 2.1示例一: 2.2示例二: 2.3注意 2.4关闭SELinux权限检查 3.升级包制作 3.1整包 3.2差分包 4.升级包上传& ...
- AUTOSAR OTA升级
一.OTA技术概念 随着高级辅助驾驶的发展和自动驾驶的引入,汽车变得越来越智能,这些智能汽车被软件控制,装有巨量的软件程序,当出现一个软件程序问题或者更新时,如果 按照传统的解决方式 ,那都将是一项很 ...
- imx6 android 最新,Re: IMX6D Android6.0 OTA 升级问题
HI All : 在调试我们imx6D Android6.0产品OTA升级的时候遇到一个问题,希望您帮忙协助分析下. 现在我们的板子是通过SD卡启动,系统运行正常. 操作如下: 我通过Make dis ...
最新文章
- TensorFlow 官方文档中文版发布啦（持续维护）
- 两个整数相加减是否溢出
- Android全屏沉浸式应用
- android data binding jetpack III 绑定一个方法
- Hey, Apple | Decode the Week
- 分布式统一配置平台-Disconf.Net
- Java 生成随机数的 N 种方法
- （125）FPGA面试题-熟悉AXI总线吗，介绍AXI
- pytorch clamp 与clamp_区别
- android如何不卡顿,公认不卡的安卓手机 轻松做到3年不卡顿_TOM科技
- 词汇表生成（C语言）
- 关于使用stanfordcorenlp一直运行不报错的解决方法
- Linux镜像模式,Linux实现HiTool的合并镜像功能
- php ma,第十四届萌芽杯优秀作品展示第一期
- 百度搜索引擎关键字URL采集爬虫优化行业定投方案高效获得行业流量-代码篇
- html5 窗口 最小化,HTML5 窗口最小化动画（先压扁后变窄）
- android开发微信分享隐藏logo,前两天刚刚做了微信分享自定义logo和文字，做个标记，从零开始记录...
- 3星|李笑来《财富自由之路》：标题党，励志书，提到一点投资技巧
- 关于PhotoShop中保存CMYK格式TIFF文件在GDI+错误地显示颜色的问题解决方法
- 小白都能学会的Python基础 第四讲：Python函数与模块
热门文章
- world wind java_WorldWind Java 版学习：1、启动过程
- 网页服务器无响应怎么回事,服务器无响应是怎么回事？dns服务器无响应怎么办？...
- 推荐 ：谷歌微软等科技巨头数据科学岗位面试题（108道）
- Go 1.17 RC2发布 | Gopher Daily (2021.08.03) ʕ◔ϖ◔ʔ
- 释义：Linear temporal logic （LTL）浅析
- 如何管理计算机的游戏,我的计算机上有一个Master Lu游戏库，无法在控制面板中找到，也找不到360软件管理. 如何卸载？...
- 软件系统的架构，反映人是公司组织结构
- php采集一言代码_【PHP】简单的一言API源码
- Netty入门——概述
- urllib 模块 https://www.cnblogs.com/guishou/articles/7089496.html