GD32F303固件库开发（14）----IIC之配置OLED
2024-05-17 09:17:00
GD32F303固件库开发.13----定时器TIM捕获PWM测量频率与占空比
- 概述
- 视频教学
- csdn课程
- 参考文档
- 时钟使能
- 初始化IO
- IIC初始化
- 配置IIC接口
- 修改IIC发送代码
- OLED
- 参考程序
- 取模
- 图片
- 显示图片
- OLED.C
- OLED.h
- OLEDFONT.H
概述
本章配置GD32F303使用IIC进行驱动SSD1306的12864OLED。
查阅手册可以得知，PB10、PB11为I2C的接口。
需要GD样片的可以加群申请：615061293 。
视频教学
https://www.bilibili.com/video/BV1od4y1u7t7/
GD32F303固件库开发（14）----IIC之配置OLED
csdn课程
课程更加详细。
https://download.csdn.net/course/detail/37144
参考文档
GD官方文档GD32F30x_Firmware_Library_V2.1.4下面IIC的Master_transmitter&slave_receiver
时钟使能
/*!\brief enable the peripheral clock\param[in] none\param[out] none\retval none
*/
void rcu_config(void)
{/* enable GPIOB clock */rcu_periph_clock_enable(RCU_GPIOB);/* enable I2C1 clock */rcu_periph_clock_enable(RCU_I2C1);
}
初始化IO
/*!\brief cofigure the GPIO ports\param[in] none\param[out] none\retval none
*/
void gpio_config(void)
{/* connect PB10 to I2C1_SCL *//* connect PB11 to I2C1_SDA */gpio_init(GPIOB, GPIO_MODE_AF_OD, GPIO_OSPEED_50MHZ, GPIO_PIN_10 | GPIO_PIN_11);
}
IIC初始化
/*!\brief cofigure the I2C0 and I2C1 interfaces\param[in] none\param[out] none\retval none
*/
void i2c_config(void)
{i2c_clock_config(I2C1, 100000, I2C_DTCY_2);/* I2C address configure */i2c_mode_addr_config(I2C1, I2C_I2CMODE_ENABLE, I2C_ADDFORMAT_7BITS, 0x78);/* enable I2C1 */i2c_enable(I2C1);/* enable acknowledge */i2c_ack_config(I2C1, I2C_ACK_ENABLE);
}
配置IIC接口
/*!\brief cofigure the I2C1 interfaces\param[in] none\param[out] none\retval none
*/
void i2c_config(void)
{/* configure I2C1 clock */i2c_clock_config(I2C1, 100000, I2C_DTCY_2);/* configure I2C1 address */i2c_mode_addr_config(I2C1, I2C_I2CMODE_ENABLE, I2C_ADDFORMAT_7BITS, 0x78);/* enable I2C1 */i2c_enable(I2C1);/* enable acknowledge */i2c_ack_config(I2C1, I2C_ACK_ENABLE);
}修改IIC发送代码
将Master_transmitter&slave_receiver的IIC发送代码进行修改
/*** @brief I2C1写函数* @param addr设备地址* @param pdata 数据指针* @param data_length 数据长度*/
void i2c_write(uint8_t addr, uint8_t *pdata, uint32_t data_length)
{uint32_t i;/* wait until I2C bus is idle */while(i2c_flag_get(I2C1, I2C_FLAG_I2CBSY));//等待总线空闲/* send a start condition to I2C bus */i2c_start_on_bus(I2C1);//发送start信号/* wait until SBSEND bit is set */while(!i2c_flag_get(I2C1, I2C_FLAG_SBSEND)); //起始位是否发送/* send slave address to I2C bus */i2c_master_addressing(I2C1, addr, I2C_TRANSMITTER);//设置从机地址和执行发送操作/* wait until ADDSEND bit is set */while(!i2c_flag_get(I2C1, I2C_FLAG_ADDSEND));//主机模式下地址是否发送/* clear ADDSEND bit */i2c_flag_clear(I2C1, I2C_FLAG_ADDSEND);//清除标志位主机模式下地址是否发送/* wait until the transmit data buffer is empty */while(!i2c_flag_get(I2C1, I2C_FLAG_TBE));//发送期间I2C_DATA为空for(i = 0; i < data_length; i++){/* data transmission */i2c_data_transmit(I2C1, pdata[i]);//发送数据/* wait until the TBE bit is set */while(!i2c_flag_get(I2C1, I2C_FLAG_TBE));//发送期间I2C_DATA为空}/* send a stop condition to I2C bus */i2c_stop_on_bus(I2C1);//在I2C总线上生成停止位/* wait until stop condition generate */ while(I2C_CTL0(I2C1)&0x0200); //等待直到停止条件生成
}OLED
查看文档可以知道地址为b0111100或者b0111101，当R/W位置写0的时候，才能进行写的操作，那么地址默认为0x78(b01111000)或者0x7A(b01111010)
参考程序
这里使用0.96OLED显示屏_STM32F103C8_IIC_V1.0来进行移植
查看工程可以知道主要是有3个文件来进行OLED的驱动，移入OLE.h .c 、oledfont.h 、 bmp.h
移入文件之后要注意导入C文件。
记得添加路径。
删除没有用的头文件
删除sys.h文件
删除delay.h文件
可以查看stdint.h
在oled.h中添加u8 u32定义 也可以直接修改
typedef unsigned char u8;
typedef unsigned int u32;
先把oled.h添加主程序中。
查看oled.h，可以看到IIC定义，同时也是模拟IIC，可以注释掉
查看oled.c，可以看到是模拟iic，这些都可以注释不要，我们使用的是iIC，不是模拟。
将IIC写放入oled.c中。
记得导入#include "gd32f30x_i2c.h"头文件
记得在oled.h中申明
要使用uint8和uint32，导入头文件#include “stdint.h”
IIC写一个字节可以修改为如下所示。
/**********************************************
// IIC Write byte
**********************************************/void Write_IIC_Byte(unsigned char IIC_Byte)
{
// unsigned char i;
// unsigned char m,da;
// da=IIC_Byte;
// OLED_SCLK_Clr();
// for(i=0;i<8;i++)
// {
// m=da;
// // OLED_SCLK_Clr();
// m=m&0x80;
// if(m==0x80)
// {OLED_SDIN_Set();}
// else OLED_SDIN_Clr();
// da=da<<1;
// OLED_SCLK_Set();
// OLED_SCLK_Clr();
// }uint8_t byte[1] = {};
byte[0]=IIC_Byte;
i2c_write(0x78,byte, 1);
}
IIC写指令
向0x78设备写命令0x00的IIC_Command指令。
/**********************************************
// IIC Write Command
**********************************************/
void Write_IIC_Command(unsigned char IIC_Command)
{
// IIC_Start();
// Write_IIC_Byte(0x78); //Slave address,SA0=0
// IIC_Wait_Ack();
// Write_IIC_Byte(0x00); //write command
// IIC_Wait_Ack();
// Write_IIC_Byte(IIC_Command);
// IIC_Wait_Ack();
// IIC_Stop();uint8_t byte[2] = {}; byte[0] =0x00;byte[1] =IIC_Command; i2c_write(0x78,byte, 2);
}
IIC写数据
向0x78设备写数据0x40的IIC_Data指令。
/**********************************************
// IIC Write Data
**********************************************/
void Write_IIC_Data(unsigned char IIC_Data)
{
// IIC_Start();
// Write_IIC_Byte(0x78); //D/C#=0; R/W#=0
// IIC_Wait_Ack();
// Write_IIC_Byte(0x40); //write data
// IIC_Wait_Ack();
// Write_IIC_Byte(IIC_Data);
// IIC_Wait_Ack();
// IIC_Stop();uint8_t byte[2] = {}; byte[0] =0x40;byte[1] =IIC_Data; i2c_write(0x78,byte, 2); }
在oled.c中，OLED_Init初始化可以注释掉gpio初始化
在oled.c中，OLED_Init初始化中有个延时800ms。
导入
#include “systick.h”
可以使用delay_1ms(800);
取模
在oledfont.h中放入字库
char Hzk[][32]={// 记(0) 帖(1) 年(2) 月(3) 日(4){0x40,0x40,0x42,0xCC,0x00,0x00,0x00,0x84,0x84,0x84,0x84,0x84,0xFC,0x00,0x00,0x00},
{0x00,0x00,0x00,0x7F,0x20,0x10,0x00,0x3F,0x40,0x40,0x40,0x40,0x41,0x40,0x70,0x00},/*"记",0*/
/* (16 X 16 , 宋体 )*/{0x00,0xF8,0x08,0xFF,0x08,0xF8,0x00,0x00,0x00,0x00,0xFF,0x10,0x10,0x10,0x10,0x00},
{0x00,0x0F,0x00,0xFF,0x08,0x0F,0x00,0xFF,0x41,0x41,0x41,0x41,0x41,0xFF,0x00,0x00},/*"帖",1*/
/* (16 X 16 , 宋体 )*/{0x00,0x20,0x18,0xC7,0x44,0x44,0x44,0x44,0xFC,0x44,0x44,0x44,0x44,0x04,0x00,0x00},
{0x04,0x04,0x04,0x07,0x04,0x04,0x04,0x04,0xFF,0x04,0x04,0x04,0x04,0x04,0x04,0x00},/*"年",2*/
/* (16 X 16 , 宋体 )*/{0x00,0x00,0x00,0xFE,0x22,0x22,0x22,0x22,0x22,0x22,0x22,0x22,0xFE,0x00,0x00,0x00},
{0x80,0x40,0x30,0x0F,0x02,0x02,0x02,0x02,0x02,0x02,0x42,0x82,0x7F,0x00,0x00,0x00},/*"月",3*/
/* (16 X 16 , 宋体 )*/{0x00,0x00,0x00,0xFE,0x82,0x82,0x82,0x82,0x82,0x82,0x82,0xFE,0x00,0x00,0x00,0x00},
{0x00,0x00,0x00,0xFF,0x40,0x40,0x40,0x40,0x40,0x40,0x40,0xFF,0x00,0x00,0x00,0x00},/*"日",4*/
/* (16 X 16 , 宋体 )*/};
在main.c中添加显示
OLED_Init(); //初始化OLEDOLED_Clear() ; OLED_ShowCHinese(0,0,0);//记OLED_ShowCHinese(16,0,1);//帖OLED_ShowNum(0,2,2022,4,16);//显示ASCII字符的码值OLED_ShowCHinese(32,2,2);//年OLED_ShowNum(48,2,9,1,16);//显示ASCII字符的码值OLED_ShowCHinese(64,2,3);//月OLED_ShowNum(80,2,10,2,16);//显示ASCII字符的码值OLED_ShowCHinese(96,2,4);//日
字体大小只有2个
显示字符
OLED_ShowString(40,2,"ZXY",8);
图片
图片放在bmp.h中。
#ifndef __BMP_H
#define __BMP_Hunsigned char BMP1[]={
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x1F,0x1F,0x1F,0x7F,0xFF,0xFF,
0xFF,0xFF,0xFF,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x0F,0x0F,
0x0F,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,
0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xC7,0xC7,0xC7,0xC4,0x04,0x04,0x04,0x07,0xFF,
0xFF,0xFF,0xFF,0x0F,0x0F,0x0F,0x0F,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x80,0x80,
0x80,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xE3,0xE3,0xE3,0xE3,0xE3,0xE3,
0xE3,0xE3,0xE3,0xE3,0xE3,0xE3,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x00,0x00,0x00,0x00,0x1F,
0x1F,0x1F,0xFF,0x00,0x00,0x00,0x00,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x8F,0x8F,0x8F,
0x8F,0x8F,0x8F,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x0F,0x0F,0x0F,
0x0F,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFE,0x06,0x06,0x07,0x0F,
0xFF,0xFF,0xFF,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0x00,0x00,
0x00,0x00,0xF8,0xF8,0xF8,0xF8,0xF8,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x00,0x00,0x00,
0x00,0xC7,0xC7,0xC7,0xC7,0xC7,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x00,0x00,0x00,0x00,
0xFF,0x00,0x00,0x00,0xFF,0xFF,0x0F,0x0F,0x0F,0xFF,0xFF,0xFF,0xFF,0xFF,0x00,0x00,
0x00,0x00,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x03,0x03,0x03,0x03,0xE3,0xE0,0xE0,0xE0,
0xE0,0xE3,0xE3,0x03,0x03,0x03,0x03,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xF0,0xF0,0xF0,0xF0,
0xFF,0xF0,0xF0,0xF0,0xFF,0xFF,0xF0,0xF0,0xF0,0xFF,0xFF,0xFF,0xFF,0xFF,0xF0,0xF0,
0xF0,0xF0,0xF0,0xF8,0xF8,0xF8,0xFF,0xFF,0xF0,0xF0,0xF0,0xF0,0xF1,0xF1,0xF1,0xF1,
0xF1,0xF1,0xF1,0xF0,0xF0,0xF0,0xF0,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,/*"D:\GD32F303\GD32F30x_Firmware_Library_V2.1.4_iic_oled\记帖.bmp",0*/
/* (64 X 64 )*/};#endif显示图片
delay_1ms(2000);OLED_Clear(); OLED_DrawBMP(0,0,64,8,BMP1); //图片显示(图片显示慎用，生成的字表较大，会占用较多空间，FLASH空间8K以下慎用)
OLED.C
//
//本程序只供学习使用，未经作者许可，不得用于其它任何用途
//记帖Q群:615061293
//B站视频：https://space.bilibili.com/26152390
//CSDN:https://blog.csdn.net/qq_24312945/
// 文 件 名 : main.c
// 版 本 号 : v2.0
// 作 者 : Evk123
// 生成日期 : 2014-0101
// 最近修改 :
// 功能描述 : 0.69寸OLED 接口演示例程(STM32F103ZE系列IIC)
// 说明:
// ----------------------------------------------------------------
// GND 电源地
// VCC 接5V或3.3v电源
// SCL 接PA5（SCL）
// SDA 接PA7（SDA）
// ----------------------------------------------------------------
//记帖Q群:615061293
//All rights reserved
//
#include "oled.h"
#include "stdlib.h"
#include "oledfont.h"#include "gd32f30x_i2c.h"
#include "systick.h"
//#include "delay.h"
//OLED的显存
//存放格式如下.
//[0]0 1 2 3 ... 127
//[1]0 1 2 3 ... 127
//[2]0 1 2 3 ... 127
//[3]0 1 2 3 ... 127
//[4]0 1 2 3 ... 127
//[5]0 1 2 3 ... 127
//[6]0 1 2 3 ... 127
//[7]0 1 2 3 ... 127
/**********************************************
//IIC Start
**********************************************/
/**********************************************
//IIC Start
**********************************************/
//void IIC_Start()
//{// OLED_SCLK_Set() ;
// OLED_SDIN_Set();
// OLED_SDIN_Clr();
// OLED_SCLK_Clr();
//}///**********************************************
IIC Stop
//**********************************************/
//void IIC_Stop()
//{
//OLED_SCLK_Set() ;
OLED_SCLK_Clr();
// OLED_SDIN_Clr();
// OLED_SDIN_Set();
//
//}//void IIC_Wait_Ack()
//{// //GPIOB->CRH &= 0XFFF0FFFF; //设置PB12为上拉输入模式
// //GPIOB->CRH |= 0x00080000;
OLED_SDA = 1;
delay_us(1);
// //OLED_SCL = 1;
// //delay_us(50000);
///* while(1)
// {
// if(!OLED_SDA) //判断是否接收到OLED 应答信号
// {
// //GPIOB->CRH &= 0XFFF0FFFF; //设置PB12为通用推免输出模式
// //GPIOB->CRH |= 0x00030000;
// return;
// }
// }
//*/
// OLED_SCLK_Set() ;
// OLED_SCLK_Clr();
//}/*** @brief I2C1写函数* @param addr设备地址* @param pdata 数据指针* @param data_length 数据长度*/
void i2c_write(uint8_t addr, uint8_t *pdata, uint32_t data_length)
{uint32_t i;/* wait until I2C bus is idle */while(i2c_flag_get(I2C1, I2C_FLAG_I2CBSY));//等待总线空闲/* send a start condition to I2C bus */i2c_start_on_bus(I2C1);//发送start信号/* wait until SBSEND bit is set */while(!i2c_flag_get(I2C1, I2C_FLAG_SBSEND)); //起始位是否发送/* send slave address to I2C bus */i2c_master_addressing(I2C1, addr, I2C_TRANSMITTER);//设置从机地址和执行发送操作/* wait until ADDSEND bit is set */while(!i2c_flag_get(I2C1, I2C_FLAG_ADDSEND));//主机模式下地址是否发送/* clear ADDSEND bit */i2c_flag_clear(I2C1, I2C_FLAG_ADDSEND);//清除标志位主机模式下地址是否发送/* wait until the transmit data buffer is empty */while(!i2c_flag_get(I2C1, I2C_FLAG_TBE));//发送期间I2C_DATA为空for(i = 0; i < data_length; i++){/* data transmission */i2c_data_transmit(I2C1, pdata[i]);//发送数据/* wait until the TBE bit is set */while(!i2c_flag_get(I2C1, I2C_FLAG_TBE));//发送期间I2C_DATA为空}/* send a stop condition to I2C bus */i2c_stop_on_bus(I2C1);//在I2C总线上生成停止位/* wait until stop condition generate */ while(I2C_CTL0(I2C1)&0x0200); //等待直到停止条件生成
}/**********************************************
// IIC Write byte
**********************************************/void Write_IIC_Byte(unsigned char IIC_Byte)
{
// unsigned char i;
// unsigned char m,da;
// da=IIC_Byte;
// OLED_SCLK_Clr();
// for(i=0;i<8;i++)
// {
// m=da;
// // OLED_SCLK_Clr();
// m=m&0x80;
// if(m==0x80)
// {OLED_SDIN_Set();}
// else OLED_SDIN_Clr();
// da=da<<1;
// OLED_SCLK_Set();
// OLED_SCLK_Clr();
// }uint8_t byte[1] = {};
byte[0]=IIC_Byte;
i2c_write(0x78,byte, 1);}/**********************************************
// IIC Write Command
**********************************************/
void Write_IIC_Command(unsigned char IIC_Command)
{
// IIC_Start();
// Write_IIC_Byte(0x78); //Slave address,SA0=0
// IIC_Wait_Ack();
// Write_IIC_Byte(0x00); //write command
// IIC_Wait_Ack();
// Write_IIC_Byte(IIC_Command);
// IIC_Wait_Ack();
// IIC_Stop();uint8_t byte[2] = {}; byte[0] =0x00;byte[1] =IIC_Command; i2c_write(0x78,byte, 2); }
/**********************************************
// IIC Write Data
**********************************************/
void Write_IIC_Data(unsigned char IIC_Data)
{
// IIC_Start();
// Write_IIC_Byte(0x78); //D/C#=0; R/W#=0
// IIC_Wait_Ack();
// Write_IIC_Byte(0x40); //write data
// IIC_Wait_Ack();
// Write_IIC_Byte(IIC_Data);
// IIC_Wait_Ack();
// IIC_Stop();
//uint8_t byte[2] = {}; byte[0] =0x40;byte[1] =IIC_Data; i2c_write(0x78,byte, 2); }
void OLED_WR_Byte(unsigned dat,unsigned cmd)
{if(cmd){Write_IIC_Data(dat);}else {Write_IIC_Command(dat);}}/********************************************
// fill_Picture
********************************************/
void fill_picture(unsigned char fill_Data)
{unsigned char m,n;for(m=0;m<8;m++){OLED_WR_Byte(0xb0+m,0); //page0-page1OLED_WR_Byte(0x00,0); //low column start addressOLED_WR_Byte(0x10,0); //high column start addressfor(n=0;n<128;n++){OLED_WR_Byte(fill_Data,1);}}
}/***********************Delay****************************************/
void Delay_50ms(unsigned int Del_50ms)
{unsigned int m;for(;Del_50ms>0;Del_50ms--)for(m=6245;m>0;m--);
}void Delay_1ms(unsigned int Del_1ms)
{unsigned char j;while(Del_1ms--){ for(j=0;j<123;j++);}
}//坐标设置void OLED_Set_Pos(unsigned char x, unsigned char y)
{ OLED_WR_Byte(0xb0+y,OLED_CMD);OLED_WR_Byte(((x&0xf0)>>4)|0x10,OLED_CMD);OLED_WR_Byte((x&0x0f),OLED_CMD);
}
//开启OLED显示
void OLED_Display_On(void)
{OLED_WR_Byte(0X8D,OLED_CMD); //SET DCDC命令OLED_WR_Byte(0X14,OLED_CMD); //DCDC ONOLED_WR_Byte(0XAF,OLED_CMD); //DISPLAY ON
}
//关闭OLED显示
void OLED_Display_Off(void)
{OLED_WR_Byte(0X8D,OLED_CMD); //SET DCDC命令OLED_WR_Byte(0X10,OLED_CMD); //DCDC OFFOLED_WR_Byte(0XAE,OLED_CMD); //DISPLAY OFF
}
//清屏函数,清完屏,整个屏幕是黑色的!和没点亮一样!!!
void OLED_Clear(void)
{ u8 i,n; for(i=0;i<8;i++) { OLED_WR_Byte (0xb0+i,OLED_CMD); //设置页地址（0~7）OLED_WR_Byte (0x00,OLED_CMD); //设置显示位置—列低地址OLED_WR_Byte (0x10,OLED_CMD); //设置显示位置—列高地址for(n=0;n<128;n++)OLED_WR_Byte(0,OLED_DATA); } //更新显示
}
void OLED_On(void)
{ u8 i,n; for(i=0;i<8;i++) { OLED_WR_Byte (0xb0+i,OLED_CMD); //设置页地址（0~7）OLED_WR_Byte (0x00,OLED_CMD); //设置显示位置—列低地址OLED_WR_Byte (0x10,OLED_CMD); //设置显示位置—列高地址for(n=0;n<128;n++)OLED_WR_Byte(1,OLED_DATA); } //更新显示
}
//在指定位置显示一个字符,包括部分字符
//x:0~127
//y:0~63
//mode:0,反白显示;1,正常显示
//size:选择字体 16/12
void OLED_ShowChar(u8 x,u8 y,u8 chr,u8 Char_Size)
{ unsigned char c=0,i=0; c=chr-' ';//得到偏移后的值if(x>Max_Column-1){x=0;y=y+2;}if(Char_Size ==16){OLED_Set_Pos(x,y); for(i=0;i<8;i++)OLED_WR_Byte(F8X16[c*16+i],OLED_DATA);OLED_Set_Pos(x,y+1);for(i=0;i<8;i++)OLED_WR_Byte(F8X16[c*16+i+8],OLED_DATA);}else { OLED_Set_Pos(x,y);for(i=0;i<6;i++)OLED_WR_Byte(F6x8[c][i],OLED_DATA);}
}
//m^n函数
u32 oled_pow(u8 m,u8 n)
{u32 result=1; while(n--)result*=m; return result;
}
//显示2个数字
//x,y :起点坐标
//len :数字的位数
//size:字体大小
//mode:模式 0,填充模式;1,叠加模式
//num:数值(0~4294967295);
void OLED_ShowNum(u8 x,u8 y,u32 num,u8 len,u8 size2)
{ u8 t,temp;u8 enshow=0; for(t=0;t<len;t++){temp=(num/oled_pow(10,len-t-1))%10;if(enshow==0&&t<(len-1)){if(temp==0){OLED_ShowChar(x+(size2/2)*t,y,' ',size2);continue;}else enshow=1; }OLED_ShowChar(x+(size2/2)*t,y,temp+'0',size2); }
}
//显示一个字符号串
void OLED_ShowString(u8 x,u8 y,u8 *chr,u8 Char_Size)
{unsigned char j=0;while (chr[j]!='\0'){ OLED_ShowChar(x,y,chr[j],Char_Size);x+=8;if(x>120){x=0;y+=2;}j++;}
}
//显示汉字
void OLED_ShowCHinese(u8 x,u8 y,u8 no)
{ u8 t,adder=0;OLED_Set_Pos(x,y); for(t=0;t<16;t++){OLED_WR_Byte(Hzk[2*no][t],OLED_DATA);adder+=1;} OLED_Set_Pos(x,y+1); for(t=0;t<16;t++){ OLED_WR_Byte(Hzk[2*no+1][t],OLED_DATA);adder+=1;}
}
/***********功能描述：显示显示BMP图片128×64起始点坐标(x,y),x的范围0～127，y为页的范围0～7*****************/
void OLED_DrawBMP(unsigned char x0, unsigned char y0,unsigned char x1, unsigned char y1,unsigned char BMP[])
{ unsigned int j=0;unsigned char x,y;if(y1%8==0) y=y1/8; else y=y1/8+1;for(y=y0;y<y1;y++){OLED_Set_Pos(x0,y);for(x=x0;x<x1;x++){ OLED_WR_Byte(BMP[j++],OLED_DATA); }}
} //初始化SSD1306
void OLED_Init(void)
{ // GPIO_InitTypeDef GPIO_InitStructure;
//// RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE); //使能A端口时钟
// GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5|GPIO_Pin_7;
// GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP; //推挽输出
// GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;//速度50MHz
// GPIO_Init(GPIOA, &GPIO_InitStructure); //初始化GPIOD3,6
// GPIO_SetBits(GPIOA,GPIO_Pin_5|GPIO_Pin_7);//delay_ms(800);
delay_1ms(800);OLED_WR_Byte(0xAE,OLED_CMD);//--display offOLED_WR_Byte(0x00,OLED_CMD);//---set low column addressOLED_WR_Byte(0x10,OLED_CMD);//---set high column addressOLED_WR_Byte(0x40,OLED_CMD);//--set start line addressOLED_WR_Byte(0xB0,OLED_CMD);//--set page addressOLED_WR_Byte(0x81,OLED_CMD); // contract controlOLED_WR_Byte(0xFF,OLED_CMD);//--128OLED_WR_Byte(0xA1,OLED_CMD);//set segment remapOLED_WR_Byte(0xA6,OLED_CMD);//--normal / reverseOLED_WR_Byte(0xA8,OLED_CMD);//--set multiplex ratio(1 to 64)OLED_WR_Byte(0x3F,OLED_CMD);//--1/32 dutyOLED_WR_Byte(0xC8,OLED_CMD);//Com scan directionOLED_WR_Byte(0xD3,OLED_CMD);//-set display offsetOLED_WR_Byte(0x00,OLED_CMD);//OLED_WR_Byte(0xD5,OLED_CMD);//set osc divisionOLED_WR_Byte(0x80,OLED_CMD);//OLED_WR_Byte(0xD8,OLED_CMD);//set area color mode offOLED_WR_Byte(0x05,OLED_CMD);//OLED_WR_Byte(0xD9,OLED_CMD);//Set Pre-Charge PeriodOLED_WR_Byte(0xF1,OLED_CMD);//OLED_WR_Byte(0xDA,OLED_CMD);//set com pin configuartionOLED_WR_Byte(0x12,OLED_CMD);//OLED_WR_Byte(0xDB,OLED_CMD);//set VcomhOLED_WR_Byte(0x30,OLED_CMD);//OLED_WR_Byte(0x8D,OLED_CMD);//set charge pump enableOLED_WR_Byte(0x14,OLED_CMD);//OLED_WR_Byte(0xAF,OLED_CMD);//--turn on oled panel
} OLED.h
//
//本程序只供学习使用，未经作者许可，不得用于其它任何用途//
// 文 件 名 : main.c
// 版 本 号 : v2.0
// 作 者 : Evk123
// 生成日期 : 2014-0101
// 最近修改 :
// 功能描述 : 0.69寸OLED 接口演示例程(STM32F103ZE系列IIC)
// 说明:
// ----------------------------------------------------------------
// GND 电源地
// VCC 接5V或3.3v电源
// SCL 接PA5（SCL）
// SDA 接PA7（SDA）
// ----------------------------------------------------------------
//记帖Q群:615061293
//B站视频：https://space.bilibili.com/26152390
//CSDN:https://blog.csdn.net/qq_24312945/
//All rights reserved
//
#ifndef __OLED_H
#define __OLED_H
//#include "sys.h"
#include "stdlib.h"
#include "stdint.h"#define OLED_MODE 0
#define SIZE 8
#define XLevelL 0x00
#define XLevelH 0x10
#define Max_Column 128
#define Max_Row 64
#define Brightness 0xFF
#define X_WIDTH 128
#define Y_WIDTH 64//-----------------OLED IIC端口定义----------------//#define OLED_SCLK_Clr() GPIO_ResetBits(GPIOA,GPIO_Pin_5)//SCL
//#define OLED_SCLK_Set() GPIO_SetBits(GPIOA,GPIO_Pin_5)//#define OLED_SDIN_Clr() GPIO_ResetBits(GPIOA,GPIO_Pin_7)//SDA
//#define OLED_SDIN_Set() GPIO_SetBits(GPIOA,GPIO_Pin_7)#define OLED_CMD 0//写命令
#define OLED_DATA 1//写数据typedef unsigned char u8;
typedef unsigned int u32;//OLED控制用函数
void OLED_WR_Byte(unsigned dat,unsigned cmd);
void OLED_Display_On(void);
void OLED_Display_Off(void);
void OLED_Init(void);
void OLED_Clear(void);
void OLED_DrawPoint(u8 x,u8 y,u8 t);
void OLED_Fill(u8 x1,u8 y1,u8 x2,u8 y2,u8 dot);
void OLED_ShowChar(u8 x,u8 y,u8 chr,u8 Char_Size);
void OLED_ShowNum(u8 x,u8 y,u32 num,u8 len,u8 size);
void OLED_ShowString(u8 x,u8 y, u8 *p,u8 Char_Size);
void OLED_Set_Pos(unsigned char x, unsigned char y);
void OLED_ShowCHinese(u8 x,u8 y,u8 no);
void OLED_DrawBMP(unsigned char x0, unsigned char y0,unsigned char x1, unsigned char y1,unsigned char BMP[]);
void Delay_50ms(unsigned int Del_50ms);
void Delay_1ms(unsigned int Del_1ms);
void fill_picture(unsigned char fill_Data);
//void Picture();
//void IIC_Start();
//void IIC_Stop();
void Write_IIC_Command(unsigned char IIC_Command);
void Write_IIC_Data(unsigned char IIC_Data);
void Write_IIC_Byte(unsigned char IIC_Byte);//void IIC_Wait_Ack();void i2c_write(uint8_t addr, uint8_t *pdata, uint32_t data_length);#endifOLEDFONT.H
#ifndef __OLEDFONT_H
#define __OLEDFONT_H
//常用ASCII表
//偏移量32
//ASCII字符集
//偏移量32
//大小:12*6
/************************************6*8的点阵************************************/
const unsigned char F6x8[][6] =
{
0x00, 0x00, 0x00, 0x00, 0x00, 0x00,// sp
0x00, 0x00, 0x00, 0x2f, 0x00, 0x00,// !
0x00, 0x00, 0x07, 0x00, 0x07, 0x00,// "
0x00, 0x14, 0x7f, 0x14, 0x7f, 0x14,// #
0x00, 0x24, 0x2a, 0x7f, 0x2a, 0x12,// $
0x00, 0x62, 0x64, 0x08, 0x13, 0x23,// %
0x00, 0x36, 0x49, 0x55, 0x22, 0x50,// &
0x00, 0x00, 0x05, 0x03, 0x00, 0x00,// '
0x00, 0x00, 0x1c, 0x22, 0x41, 0x00,// (
0x00, 0x00, 0x41, 0x22, 0x1c, 0x00,// )
0x00, 0x14, 0x08, 0x3E, 0x08, 0x14,// *
0x00, 0x08, 0x08, 0x3E, 0x08, 0x08,// +
0x00, 0x00, 0x00, 0xA0, 0x60, 0x00,// ,
0x00, 0x08, 0x08, 0x08, 0x08, 0x08,// -
0x00, 0x00, 0x60, 0x60, 0x00, 0x00,// .
0x00, 0x20, 0x10, 0x08, 0x04, 0x02,// /
0x00, 0x3E, 0x51, 0x49, 0x45, 0x3E,// 0
0x00, 0x00, 0x42, 0x7F, 0x40, 0x00,// 1
0x00, 0x42, 0x61, 0x51, 0x49, 0x46,// 2
0x00, 0x21, 0x41, 0x45, 0x4B, 0x31,// 3
0x00, 0x18, 0x14, 0x12, 0x7F, 0x10,// 4
0x00, 0x27, 0x45, 0x45, 0x45, 0x39,// 5
0x00, 0x3C, 0x4A, 0x49, 0x49, 0x30,// 6
0x00, 0x01, 0x71, 0x09, 0x05, 0x03,// 7
0x00, 0x36, 0x49, 0x49, 0x49, 0x36,// 8
0x00, 0x06, 0x49, 0x49, 0x29, 0x1E,// 9
0x00, 0x00, 0x36, 0x36, 0x00, 0x00,// :
0x00, 0x00, 0x56, 0x36, 0x00, 0x00,// ;
0x00, 0x08, 0x14, 0x22, 0x41, 0x00,// <
0x00, 0x14, 0x14, 0x14, 0x14, 0x14,// =
0x00, 0x00, 0x41, 0x22, 0x14, 0x08,// >
0x00, 0x02, 0x01, 0x51, 0x09, 0x06,// ?
0x00, 0x32, 0x49, 0x59, 0x51, 0x3E,// @
0x00, 0x7C, 0x12, 0x11, 0x12, 0x7C,// A
0x00, 0x7F, 0x49, 0x49, 0x49, 0x36,// B
0x00, 0x3E, 0x41, 0x41, 0x41, 0x22,// C
0x00, 0x7F, 0x41, 0x41, 0x22, 0x1C,// D
0x00, 0x7F, 0x49, 0x49, 0x49, 0x41,// E
0x00, 0x7F, 0x09, 0x09, 0x09, 0x01,// F
0x00, 0x3E, 0x41, 0x49, 0x49, 0x7A,// G
0x00, 0x7F, 0x08, 0x08, 0x08, 0x7F,// H
0x00, 0x00, 0x41, 0x7F, 0x41, 0x00,// I
0x00, 0x20, 0x40, 0x41, 0x3F, 0x01,// J
0x00, 0x7F, 0x08, 0x14, 0x22, 0x41,// K
0x00, 0x7F, 0x40, 0x40, 0x40, 0x40,// L
0x00, 0x7F, 0x02, 0x0C, 0x02, 0x7F,// M
0x00, 0x7F, 0x04, 0x08, 0x10, 0x7F,// N
0x00, 0x3E, 0x41, 0x41, 0x41, 0x3E,// O
0x00, 0x7F, 0x09, 0x09, 0x09, 0x06,// P
0x00, 0x3E, 0x41, 0x51, 0x21, 0x5E,// Q
0x00, 0x7F, 0x09, 0x19, 0x29, 0x46,// R
0x00, 0x46, 0x49, 0x49, 0x49, 0x31,// S
0x00, 0x01, 0x01, 0x7F, 0x01, 0x01,// T
0x00, 0x3F, 0x40, 0x40, 0x40, 0x3F,// U
0x00, 0x1F, 0x20, 0x40, 0x20, 0x1F,// V
0x00, 0x3F, 0x40, 0x38, 0x40, 0x3F,// W
0x00, 0x63, 0x14, 0x08, 0x14, 0x63,// X
0x00, 0x07, 0x08, 0x70, 0x08, 0x07,// Y
0x00, 0x61, 0x51, 0x49, 0x45, 0x43,// Z
0x00, 0x00, 0x7F, 0x41, 0x41, 0x00,// [
0x00, 0x55, 0x2A, 0x55, 0x2A, 0x55,// 55
0x00, 0x00, 0x41, 0x41, 0x7F, 0x00,// ]
0x00, 0x04, 0x02, 0x01, 0x02, 0x04,// ^
0x00, 0x40, 0x40, 0x40, 0x40, 0x40,// _
0x00, 0x00, 0x01, 0x02, 0x04, 0x00,// '
0x00, 0x20, 0x54, 0x54, 0x54, 0x78,// a
0x00, 0x7F, 0x48, 0x44, 0x44, 0x38,// b
0x00, 0x38, 0x44, 0x44, 0x44, 0x20,// c
0x00, 0x38, 0x44, 0x44, 0x48, 0x7F,// d
0x00, 0x38, 0x54, 0x54, 0x54, 0x18,// e
0x00, 0x08, 0x7E, 0x09, 0x01, 0x02,// f
0x00, 0x18, 0xA4, 0xA4, 0xA4, 0x7C,// g
0x00, 0x7F, 0x08, 0x04, 0x04, 0x78,// h
0x00, 0x00, 0x44, 0x7D, 0x40, 0x00,// i
0x00, 0x40, 0x80, 0x84, 0x7D, 0x00,// j
0x00, 0x7F, 0x10, 0x28, 0x44, 0x00,// k
0x00, 0x00, 0x41, 0x7F, 0x40, 0x00,// l
0x00, 0x7C, 0x04, 0x18, 0x04, 0x78,// m
0x00, 0x7C, 0x08, 0x04, 0x04, 0x78,// n
0x00, 0x38, 0x44, 0x44, 0x44, 0x38,// o
0x00, 0xFC, 0x24, 0x24, 0x24, 0x18,// p
0x00, 0x18, 0x24, 0x24, 0x18, 0xFC,// q
0x00, 0x7C, 0x08, 0x04, 0x04, 0x08,// r
0x00, 0x48, 0x54, 0x54, 0x54, 0x20,// s
0x00, 0x04, 0x3F, 0x44, 0x40, 0x20,// t
0x00, 0x3C, 0x40, 0x40, 0x20, 0x7C,// u
0x00, 0x1C, 0x20, 0x40, 0x20, 0x1C,// v
0x00, 0x3C, 0x40, 0x30, 0x40, 0x3C,// w
0x00, 0x44, 0x28, 0x10, 0x28, 0x44,// x
0x00, 0x1C, 0xA0, 0xA0, 0xA0, 0x7C,// y
0x00, 0x44, 0x64, 0x54, 0x4C, 0x44,// z
0x14, 0x14, 0x14, 0x14, 0x14, 0x14,// horiz lines
};
/****************************************8*16的点阵************************************/
const unsigned char F8X16[]=
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,// 00x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x33,0x30,0x00,0x00,0x00,//! 10x00,0x10,0x0C,0x06,0x10,0x0C,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//" 20x40,0xC0,0x78,0x40,0xC0,0x78,0x40,0x00,0x04,0x3F,0x04,0x04,0x3F,0x04,0x04,0x00,//# 30x00,0x70,0x88,0xFC,0x08,0x30,0x00,0x00,0x00,0x18,0x20,0xFF,0x21,0x1E,0x00,0x00,//$ 40xF0,0x08,0xF0,0x00,0xE0,0x18,0x00,0x00,0x00,0x21,0x1C,0x03,0x1E,0x21,0x1E,0x00,//% 50x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00,0x1E,0x21,0x23,0x24,0x19,0x27,0x21,0x10,//& 60x10,0x16,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//' 70x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00,0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00,//( 80x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00,0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00,//) 90x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00,0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00,//* 100x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x1F,0x01,0x01,0x01,0x00,//+ 110x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xB0,0x70,0x00,0x00,0x00,0x00,0x00,//, 120x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,//- 130x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,//. 140x00,0x00,0x00,0x00,0x80,0x60,0x18,0x04,0x00,0x60,0x18,0x06,0x01,0x00,0x00,0x00,/// 150x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00,//0 160x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//1 170x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00,//2 180x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00,0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00,//3 190x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00,//4 200x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00,//5 210x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00,//6 220x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,//7 230x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00,//8 240x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00,//9 250x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,//: 260x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x60,0x00,0x00,0x00,0x00,//; 270x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00,0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00,//< 280x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x00,//= 290x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00,//> 300x00,0x70,0x48,0x08,0x08,0x08,0xF0,0x00,0x00,0x00,0x00,0x30,0x36,0x01,0x00,0x00,//? 310xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00,0x07,0x18,0x27,0x24,0x23,0x14,0x0B,0x00,//@ 320x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20,//A 330x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00,//B 340xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00,0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00,//C 350x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00,0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00,//D 360x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00,//E 370x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00,//F 380xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00,0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00,//G 390x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20,//H 400x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//I 410x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00,//J 420x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00,0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00,//K 430x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00,//L 440x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00,0x20,0x3F,0x00,0x3F,0x00,0x3F,0x20,0x00,//M 450x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08,0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00,//N 460xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00,//O 470x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00,0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00,//P 480xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x18,0x24,0x24,0x38,0x50,0x4F,0x00,//Q 490x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00,0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20,//R 500x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00,0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00,//S 510x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//T 520x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//U 530x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00,//V 540xF8,0x08,0x00,0xF8,0x00,0x08,0xF8,0x00,0x03,0x3C,0x07,0x00,0x07,0x3C,0x03,0x00,//W 550x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08,0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20,//X 560x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//Y 570x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00,0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00,//Z 580x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00,//[ 590x00,0x0C,0x30,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00,//\ 600x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00,//] 610x00,0x00,0x04,0x02,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//^ 620x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,//_ 630x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//` 640x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x19,0x24,0x22,0x22,0x22,0x3F,0x20,//a 650x08,0xF8,0x00,0x80,0x80,0x00,0x00,0x00,0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00,//b 660x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00,//c 670x00,0x00,0x00,0x80,0x80,0x88,0xF8,0x00,0x00,0x0E,0x11,0x20,0x20,0x10,0x3F,0x20,//d 680x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x22,0x13,0x00,//e 690x00,0x80,0x80,0xF0,0x88,0x88,0x88,0x18,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//f 700x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00,//g 710x08,0xF8,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//h 720x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//i 730x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,//j 740x08,0xF8,0x00,0x00,0x80,0x80,0x80,0x00,0x20,0x3F,0x24,0x02,0x2D,0x30,0x20,0x00,//k 750x00,0x08,0x08,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//l 760x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F,//m 770x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//n 780x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//o 790x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00,0x80,0xFF,0xA1,0x20,0x20,0x11,0x0E,0x00,//p 800x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x0E,0x11,0x20,0x20,0xA0,0xFF,0x80,//q 810x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00,//r 820x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00,//s 830x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00,//t 840x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20,//u 850x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x00,0x01,0x0E,0x30,0x08,0x06,0x01,0x00,//v 860x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80,0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00,//w 870x00,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x31,0x2E,0x0E,0x31,0x20,0x00,//x 880x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x80,0x81,0x8E,0x70,0x18,0x06,0x01,0x00,//y 890x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00,//z 900x00,0x00,0x00,0x00,0x80,0x7C,0x02,0x02,0x00,0x00,0x00,0x00,0x00,0x3F,0x40,0x40,//{ 910x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,//| 920x00,0x02,0x02,0x7C,0x80,0x00,0x00,0x00,0x00,0x40,0x40,0x3F,0x00,0x00,0x00,0x00,//} 930x00,0x06,0x01,0x01,0x02,0x02,0x04,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//~ 94
};
char Hzk[][32]={// 记(0) 帖(1) 年(2) 月(3) 日(4){0x40,0x40,0x42,0xCC,0x00,0x00,0x00,0x84,0x84,0x84,0x84,0x84,0xFC,0x00,0x00,0x00},
{0x00,0x00,0x00,0x7F,0x20,0x10,0x00,0x3F,0x40,0x40,0x40,0x40,0x41,0x40,0x70,0x00},/*"记",0*/
/* (16 X 16 , 宋体 )*/{0x00,0xF8,0x08,0xFF,0x08,0xF8,0x00,0x00,0x00,0x00,0xFF,0x10,0x10,0x10,0x10,0x00},
{0x00,0x0F,0x00,0xFF,0x08,0x0F,0x00,0xFF,0x41,0x41,0x41,0x41,0x41,0xFF,0x00,0x00},/*"帖",1*/
/* (16 X 16 , 宋体 )*/{0x00,0x20,0x18,0xC7,0x44,0x44,0x44,0x44,0xFC,0x44,0x44,0x44,0x44,0x04,0x00,0x00},
{0x04,0x04,0x04,0x07,0x04,0x04,0x04,0x04,0xFF,0x04,0x04,0x04,0x04,0x04,0x04,0x00},/*"年",2*/
/* (16 X 16 , 宋体 )*/{0x00,0x00,0x00,0xFE,0x22,0x22,0x22,0x22,0x22,0x22,0x22,0x22,0xFE,0x00,0x00,0x00},
{0x80,0x40,0x30,0x0F,0x02,0x02,0x02,0x02,0x02,0x02,0x42,0x82,0x7F,0x00,0x00,0x00},/*"月",3*/
/* (16 X 16 , 宋体 )*/{0x00,0x00,0x00,0xFE,0x82,0x82,0x82,0x82,0x82,0x82,0x82,0xFE,0x00,0x00,0x00,0x00},
{0x00,0x00,0x00,0xFF,0x40,0x40,0x40,0x40,0x40,0x40,0x40,0xFF,0x00,0x00,0x00,0x00},/*"日",4*/
/* (16 X 16 , 宋体 )*/};#endif以上的代码会在Q_qun里分享。QQ_qun：615061293。
或者关注『记帖』，持续更新文章和学习资料!
GD32F303固件库开发（14）----IIC之配置OLED相关推荐
- GD32F303固件库开发（7）----printf打印配置
GD32F303固件库开发.7----printf打印配置 概述 视频教学 csdn课程 样品申请 硬件准备 keil配置 串口初始化 最后 串口重定向 打印测试 测试结果 概述 本章主要配置prin ...
- GD32F303固件库开发
GD32F303固件库开发 芯片申请 GD32F303固件库开发(1)----前期准备与烧录 GD32F303固件库开发(2)----读保护与写保护 GD32F303固件库开发(3)----使用固件库 ...
- GD32F303固件库开发（16）----移植兆易创新SPI Nor Flash之GD25Q64Flash
spi概述 SPI是串行外设接口(Serial Peripheral Interface)的缩写,是一种高速的,全双工,同步的通信总线,并且在芯片的管脚上只占用四根线,节约了芯片的管脚,同时为PCB的 ...
- GD32F303固件库开发（5）----GPIO输出模式，速率测试、开漏和输出说明
GD32F303固件库开发.5----GPIO输出模式,速率测试.开漏和输出说明 概述 样品申请 视频教学 csdn课程 硬件准备 开发板管脚配置 不同速率对应的波形 GPIO_OSPEED_2MHZ ...
- GD32F303固件库开发（10）----双ADC轮询模式扫描多个通道
GD32F303固件库开发.10----双ADC轮询模式扫描多个通道 概述 视频教学 csdn课程 样品申请 硬件准备 keil配置 使能串口 串口重定向 ADC通道设置 ADC0初始化 ADC0配置 ...
- GD32F303固件库开发（11）----ADC在DMA模式下扫描多个通道
GD32F303固件库开发.11----双ADC轮询模式扫描多个通道 概述 视频教学 csdn课程 样品申请 硬件准备 keil配置 使能串口 串口重定向 ADC通道设置 DMA设置 ADC0初始化 ...
- GD32F303固件库开发（13）----定时器TIM捕获PWM测量频率与占空比
GD32F303固件库开发.13----定时器TIM捕获PWM测量频率与占空比 概述 视频教学 csdn课程 样品申请 生成例程 keil配置 使能串口 串口重定向 占空比与频率计算 GPIO初始化 ...
- GD32F303固件库开发（17）----内部Flash读写
概述 本例程主要讲解如何对芯片自带Flash进行读写,用芯片内部Flash可以对一些需要断电保存的数据进行保存,无需加外部得存储芯片,本例程采用的是GD32F303ZET6主控,512K大小的Flas ...
- STM32CUBEMX开发GD32F303（14）----IIC之配置OLED
STM32CUBEMX开发GD32F303.14----IIC之配置OLED 概述 视频教学 csdn课程 样品申请 生成例程 配置时钟树 IIC配置 OLED 参考程序 HAL_I2C_Mem_Wr ...
最新文章
- 学习笔记之三(数组中的一些方法)
- 「模型解读」“不正经”的卷积神经网络
- 解决html页面闪烁,解决前端页面闪烁问题（转载）
- 编译openwrt时报错:g++: internal compiler error: Killed (program cc1plus)
- 程序员面试题精选100题(35)-两链表的第一个公共结点[数据结构]
- Java 类中各成分加载顺序和内存中的存放位置
- C#中对虚拟属性和抽象属性的重写，重写label实例
- python心得-基本概念2
- java中多态_java之多态
- 蓝桥杯 ALGO-115 算法训练 和为T Java版
- html脚本src,HTML script脚本标签
- Centos 7 修改 Mysql 5.7 默认端口号
- Java使用apache的poi将PPT转PDF文件，支持并兼容PPT和PPTX文件
- 物联网NodeMCU刷写AT固件
- LOJ#6070. 「2017 山东一轮集训 Day4」基因 解题报告
- springboot项目报错-The Bean Validation API is on the classpath but no implementation could be found
- 2022年最新版Android安卓面试题+答案精选（每日20题，持续更新中）【八】
- c语言 continue什么意思,continue在C语言中什么意思？
- CF831A-Unimodal Array（单峰阵列）
- 用ios企业证书发布ipa到服务器上扫码下载