Pass4side EMC Symmetrix Business Continuity Expert Exam for Storage Admins E20-817认证考试题库
如果你正在准备E20-817考试，为E20-817认证做最后冲刺，又苦于没有绝对权威的考试真题模拟，Pass4Side希望能助你成功。
为了确保您对Pass4side的E20-817权威考试题库的信任，以下是本题库的参考DEMO .
1. Click the Exhibit button.
During the design process of a Star implementation, a customer expresses the intention to switch production to one of the target sites as part of a disaster drill. After the production has been switched, the customer wishes to run Star protection at this site.
What should you advise?

A.It does not matter which site the customer switches production to, because Star protection cannot be enabled when the workload is running at a target site.E20-817
B.Servers and management hosts may be provided at either site, because Star protectioE20-817n can be enabled while the workload is running at either target site.
C.Servers and management hosts should be provided at site B, because Star protection can only be enabled if the workload is switched to the Synchronous target site.
D.Servers and management hosts should be provided at site C, because Star protection caE20-817n only be enabled if the workload is switched to the Asynchronous target site.
Answer: C

2. Click on the Exhibit.E20-817
In an SRDF/Star implementation, the Connected state indicates which condition has occurred?

A.Both links are transmitting data, but one or both target sites are not fully synchronized with the workload site
B.The RDF relationship is not properly defined or there is no data flow between the sites.
C.The RDF relationship is properly defined, but the target site in E20-817question is not synchronized with the workload site and there is no consistency protection for the remote data.
D.The RDF relationship is properly defined, dependent write consistency of the data at the synchronous target site is assured through RDF-ECA and dependent write consistency at the asynchronous target is assured through MSC.
Answer: A
3. Click the Exhibit button.
The diagram shows a planned Star configuration with two Symmetrix arrays at each site. The options file to be used for setting up Star is shown on the left.
RDF Groups 5 and 6 on arrays A1 and A2 connect to arrays B1 and B2.
RDF Groups 15 and 16 on arrays A1 and A2 connect to arrays C1 and C2.
RDF Groups 55 and 56 on arrays E20-817B1 and B2 connect to arrays C1 and C2.
Which RDF groups in the configuration should be assigned the name SiteB?

A.5 and 15
B.5 and 6
C.55 and 56
D.6 and 16
Answer: B
4. A customer running SRDF/StE20-817ar experienced a workload site failure. Production was switched from the workload site A to the synchronous target site B. Some time later, site A came back online. Before switching production back to site A, a symdev show command is executed to examine the R1 devices at site A.
What is the RDF configuration state that describes the relationship of the RDF devices between A and B?
A.Duplicate
B.Half
C.Normal
D.PartitionedAnswer: A
5. A customer has a 5 (five) node Microsoft cluster (MSCS) that spans across 2 (two) sites over a SRDF/A link.
Site A, the primary site, contains 3 (three) nodes. Site B, the remote site, contains 2 (two) nodes. If the customer is using SRDF/CE with Majority Note Set (MNS), what happens to the nodes at Site A if communication is lost between the 2 (two) sites?
A.Nodes at Site A and Site B will go offline until communication resumes to Site B. The nodes at both sites need to be started manually, and the /ForceQuorum switch must be used.E20-817
B.Nodes at Site A will go offline until communication resumes to Site B. The nodes at Site A need to be started manually and the /ForceQuorum switch must be used.
C.Nodes at Site A will go offline until the nodes at Site A are manually started and the /ForceQuorum switch is used.
D.Nodes will remain online.Answer: D

本文摘自：[url]http://www.alisaga.cn/[/url]
更多考试题库可登陆：WWW.pass4side.cn