FT232H USB转串口,I2C,JTAG高速芯片

随着FT232H USB2.0高速芯片的发布，英商飞特蒂亚公司(FTDI)进一步巩固了其在USB接口集成电路产品的地位。此款多功能的单通道USB转UART/FIFO接口设备可通过EEPROM配置为各种不同的串行或并行接口。与FTDI建设完备精良的USB设备驱动一起，这套方案使工程师可以轻松的将高速 USB连接引入新的和传统的外设设计中。另外，还有相关的UM232H评估模块帮助工程师快速建立设计样机，测试FT232H集成到新的系统设计的适用性。其高度集成的USB设备控制器包含USB，串行和并行协议引擎，而不需要开发USB专用固件。设备支持3.3V的IO接口电平，允许5V输入，使之适用于连接各种逻辑，MPU和FPGA。

FT232H不仅支持异步串行接口（UART），还通过其内建的多协议同步串行引擎（MPSSE）支持许多同步IO接口，比如SPI， I2C，JTAG以及FPGA编程接口，MPSSE通信速度能够达到30M比特/秒。另外，MPSSE可用于执行设计工程师自己的同步串行总线协议。

新的FT1248 总线是FT232H集成的一个接口功能，为专有的同步半双工串行/并行接口，与外部逻辑通信速率可以达到30M Byte/秒。FT1248 总线独特之处在于能够根据可用物理数据总线的数量（1，2，4或8）调整FT232H与外部逻辑连接的带宽，从而为系统设计提供最优的适应性。

集成的1.8V和3.3V低压差稳压器减少了所需外部元件，同时与现有的USB2.0兼容的全速产品相比较而言，1 K字节大的收发数据缓存加上USB2.0高速技术大大改善了数据吞吐量，缩减了延迟响应时间。FTDI网站可下载用于Windows, Linux, MAC 和 WinCE操作系统的免税驱动。

FT232H的封装选择有48针LQFP（FT232HL）或48针QFN（FT232HQ）无铅封装。这两种FT232H工作范围是-40⁰C ~ +85⁰C。FT232HL定价为$2.75（1,000片以上），FT232HQ定价为$2.60（1000片以上）。UM232H用户评估模块有助于快速建立原型或测试FT232H平台，与一个标准的0.6英寸宽，28针的DIP插座连接。UM232H模块单价定为$20（1~9片）。

Operating at USB Hi-Speed 480Mbps rate, this fast single channel bridge chip features either a flexible serial interface or parallel FIFO interface, with data transfer speeds up to 40Mbytes/s. Using a serial EEPROM interface, this device can be configured for a wide variety of asynchronous and synchronous serial standards, such as JTAG, SPI, I2C and UART as well as synchronous and asynchronous parallel FIFO interfaces. In addition, this device features the new synchronous, half-duplex FT1248 bus, which allows an engineer to trade off bandwidth for pin count using 1, 2, 4, or 8 data lines at up to 30Mbytes/s. The I/O structure is 3.3V with built-in tolerance for 5V, allowing the designer maximum flexibility when interfacing with FPGAs. On-board voltage regulation provides 3.3V and 1.8V supplies from a 5V source, as well as a power-on-reset function. FTDI provides royalty-free virtual com port and D2XX drivers for Microsoft Windows (XP – Windows7), Apple Mac OSX, and Linux. This 48 pin device is available in either LQFP or QFN packaging, and is ROHS compliant.

Single channel USB to serial / parallel ports with a variety of configurations.
Entire USB protocol handled on the chip. No USB specific firmware programming required.
USB 2.0 Hi-Speed (480Mbits/Second) and Full Speed (12Mbits/Second) compatible.
Multi-Protocol Synchronous Serial Engine (MPSSE) to simplify synchronous serial protocol (USB to JTAG, I2C, SPI or bit-bang) design.
UART transfer data rate up to 12Mbaud. (RS232 Data Rate limited by external level shifter).
USB to asynchronous 245 FIFO mode for transfer data rate up to 8 MByte/Sec.
USB to synchronous 245 parallel FIFO mode for transfers up to 40 Mbytes/Sec
Supports a half duplex FT1248 interface with a configurable width, bi-directional data bus (1, 2, 4 or 8 bits wide).
CPU-style FIFO interface mode simplifies CPU interface design.
Fast serial interface option.
FTDI's royalty-free Virtual Com Port (VCP) and Direct (D2XX) drivers eliminate the requirement for USB driver development in most cases.
Adjustable receive buffer timeout.
Option for transmit and receive LED drive signals.
Bit-bang Mode interface option with RD# and WR strobes
Highly integrated design includes 5V to 3.3/+1.8V LDO regulator for VCORE, integrated POR function
Asynchronous serial UART interface option with full hardware handshaking and modem interface signals.
Fully assisted hardware or X-On / X-Off software handshaking.
UART Interface supports 7/8 bit data, 1/2 stop bits, and Odd/Even/Mark/Space/No Parity.
Auto-transmit enable control for RS485 serial applications using TXDEN pin.
Operation configuration mode and USB Description strings configurable in external EEPROM over the USB interface.
Configurable I/O drives strength (4, 8, 12 or 16mA) and slew rate.
Low operating and USB suspend current.
Supports self powered, bus powered and high-power bus powered USB configurations.
UHCI/OHCI/EHCI host controller compatible.#
USB Bulk data transfer mode (512 byte packets in Hi-Speed mode).
+1.8V (chip core) and +3.3V I/O interfacing (+5V Tolerant).
Extended -40°C to 85°C industrial operating temperature range.
Compact 48-pin Lead Free LQFP or QFN package
Configurable ACBUS I/O pins.

This mode uses a synchronous interface to get high data transfer speeds. The chip drives a 60 MHz CLKOUT clock for the external system to use.
Note that Asynchronous FIFO mode must be selected in the EEPROM before selecting the Synchronous FIFO mode in software.

4.4.1 FT245 Synchronous FIFO Read Operation

A read operation is started when the chip drives RXF# low. The external system can then drive OE# low to turn the data bus drivers around before acknowledging the data with the RD# signal going low. The first data byte is on the bus after OE# is low. The external system can burst the data out of the chip by keeping RD# low or it can insert wait states in the RD# signal. If there is more data to be read it will change on the clock following RD# sampled low. Once all the data has been consumed, the chip will drive RXF# high. Any data that appears on the data bus, after RXF# is high, is invalid and should be ignored.

4.4.2 FT245 Synchronous FIFO Write Operation

A write operation can be started when TXE# is low. WR# is brought low when the data is valid. A burst operation can be done on every clock providing TXE# is still low. The external system must monitor TXE# and its own WR# to check that data has been accepted. Both TXE# and WR# must be low for data to be accepted.

4.12 Send Immediate / Wake Up (SIWU#)
The SIWU# pin is available in the FIFO modes and in bit bang mode.
The Send Immediate portion is used to flush data from the chip back to the PC. This can be used to force
short packets of data back to the PC without waiting for the latency timer to expire.
To avoid overrunning, this mechanism should only be used when a process of sending data to the chip
has been stopped.
The data transfer is flagged to the USB host by the falling edge of the SIWU# signal. The USB host will
schedule the data transfer on the next USB packet.

Figure 4.25: Using SIWU#
When the pin is being used for a Wake Up function to wake up a sleeping PC a 20ms negative pulse on
this pin is required. When the pin is used to immediately flush the buffer (Send Immediate) a 250ns
negative pulse on this pin is required.
Notes
1. When using remote wake-up, ensure the resistors are pulled-up in suspend. Also ensure peripheral
designs do not allow any current sink paths that may partially power the peripheral.
2. If remote wake-up is enabled, a peripheral is allowed to draw up to 2.5mA in suspend. If remote
wake-up is disabled, the peripheral must draw no more than 500uA in suspend.
3. If a Pull-down is enabled, the FT232H will not wake up from suspend when using SIWU#
4.In UART mode the RI# pin acts as the wake up pin.

FT232H USB转串口,I2C,JTAG高速芯片相关推荐

免驱USB转串口芯片，还支持Billboard功能
乐得瑞发布一颗USB转串口芯片LDR2001,功能强大,免驱,还支持Billboard功能. LDR2001芯片是乐得瑞科技设计的一个免驱的USB转串口的CDC类芯片,可以实现USB转串口和Billb ...
USB转串口芯片CH340E（LDR2001）
LDR2001芯片是乐得瑞科技设计的一个免驱的USB转串口的CDC类芯片,可以实现USB转串口和Billboard的功能.当使用了LDR2001芯片的设备接入USB HOST时,会在HOST端弹出Bi ...
电脑免驱乐得瑞LDR2001 USB转串口芯片方案介绍
电脑免驱乐得瑞LDR2001 USB转串口芯片方案介绍 1 概述 LDR2001 芯片是乐得瑞科技设计的一个免驱的 USB 转串口的 CDC 类芯片,可以实现USB 转串口和 Billboard 的 ...
Arm-Linux上使用国产USB转串口芯片CH9102
最近在研究I.MX6U-ALPHA这块开发板,板上已有一片USB转串口芯片CH340,通过文档我才知道大学时实验室人手一块的小神器原来是沁恒这家公司生产的.考虑到后期项目需要使用串口和不同信号电压的设 ...
Mac OS X Yosemite Arduino安装CH340 USB转串口驱动
新买的Arduino开发板 USB转串口使用了CH340芯片,在Mac OS X Yosemite上正常安装驱动后,在Arduino IDE的端口没发现相应的设备,使用以下方法后就能使用USB转串口调 ...
可编程 USB 转串口适配器开发板 SHT3x-DIS 温湿度传感器芯片
可编程 USB 转串口适配器开发板 SHT3x-DIS 温湿度传感器芯片可编程USB转 UART/I2C /SMBusS/SPI/CAN/1 -Wire适配器USB2S 的温湿传感器 1.2 ...
ft232h引脚_一种基于芯片ft232h的usb接口电路的制作方法
一种基于芯片ft232h的usb接口电路的制作方法 [技术领域] [0001 ] 本实用新型涉及一种USB接口电路,具体涉及一种基于芯片FT232H的USB接口电路. [背景技术] [0002]USB ...
USB转串口芯片CH340系列及CH340模块使用方法（CH340驱动，接线，串口下载详细介绍）
USB 转串口芯片 CH340 我们为什么要用到CH340驱动呢?CH340驱动就是USB转串口的驱动的一种,因为我们现在的电脑上,已经不存在串口,所以我们一般使用USB转串口芯片,目的只有一个,把电 ...
新一代高性能USB转串口芯片CH342与CH343
简介 CH342与CH343是沁恒推出的第三代USB转串口产品,内部高度集成,外围精简,均提供VIO电源引脚,串口I/O支持独立供电. CH342实现USB转两路高速异步串口,支持串口波特率高达3Mb ...

FT232H USB转串口,I2C,JTAG高速芯片

FT232H USB转串口,I2C,JTAG高速芯片相关推荐

最新文章

热门文章