本帖最后由 wuli小茶 于 2018-1-27 11:10 编辑

求大神帮我下，请问这是什么情况，我想刷机，买了CH340G型号的USB转TTL模块，按教程连接后打开SecureCRT或putty都是显示如下的代码，这是什么情况，急死我了！！！！！

AC_ON

MIU0_DQS-OK

BIST0-???

MIU0-1024_U

Start uboot

Relocation Offset is: 011d7000

[AT][MB][start ub][441]

U-Boot 2011.06-00125-g53e4a9c-dirty (Jan 08 2018 - 10:13:50)

[MIU INFO] miu opencreate instance at 52ee9418 with private size 80 bytes at 52ee9460

create instance at 52ee94b8 with private size 52 bytes at 52ee9500

uboot held at [52cddf60~54000000],size=013220a0

CPU  : Clippers

Board: BD_MST207C_D01A_S_CLIPPERS

DRAM:  832 MiB

Now running in RAM - U-Boot at: 53100000

eMMC: HS200 200MHz

eMMC 3.63 GB [747FF8h]

In:    serial

Out:   serial

Err:   serial

Net:   zte_shutdow =false

No ethernet found.

Set MAC default

MAC:  0x0: 0x30: 0x1b: 0xba:0x2: 0xdb

msIR_Initialize

[CPU INFO] cpu opencreate instance at 52ef99c0 with private size 44 bytes at 52ef9a08

CPUIoctl - MDrv_CMD_CPU_QueryClock

[UTOPIA INFO] close moduleNames[38]: MODULE_CPU

[AT][MBoot][Driver Init][591]

### main_loop entered: s is true

### main_loop entered: bootdelay=1

Starting logo

============= set bootargs ===============

[setup_com_controlenv] COMControlFlag=>   value[1]=, val=0

zte_mac=74:97:81:CB:E5:17,ethaddr=74:97:81:CB:E5:17

Hit any key to stop autoboot: 1@

step1 error...

abort=0                                                                       0

mxy: MAEKET_IS_SDLT=0,MarketCode=21, OperatorsCode=2

do_bootcheck called

MMC_CAPACITY_512 =7634936

current emmc size is =0x747ff8 (should by 512)

MMCusrdata_size =3901440

current userdata size =0x3b8800 (should by 512)

get_boot1_ver cmd_boot1=mmc read.boot 1 0x25000000 0x0 0x200000

set hdmi hdcp mode 0!

Saving Environment to MMC...

Writing to MMC(0)... 128 blocks written: OK

128 blocks written: OK

done

iTVSTandard2Resolution = 2

value[29] = F0000400001333400000749781CBE517

[setup_bootenv] COMControlFlag=>   value[30]=, val=0

ethaddr =74:97:81:CB:E5:17

jy ....

search ....

waldo msIR_GetIRKeyCode line:483 breturn false

fore uup IRKey [0xff]

BootMode=0

search ....

waldo msIR_GetIRKeyCode line:483 breturn false

fore uup IRKey [0xff]

BootMode=0

search ....

waldo msIR_GetIRKeyCode line:483 breturn false

fore uup IRKey [0xff]

BootMode=0

search ....

waldo msIR_GetIRKeyCode line:483 breturn false

fore uup IRKey [0xff]

BootMode=0

search ....

waldo msIR_GetIRKeyCode line:483 breturn false

fore uup IRKey [0xff]

BootMode=0

search ....

waldo msIR_GetIRKeyCode line:483 breturn false

fore uup IRKey [0xff]

BootMode=0

search ....

waldo msIR_GetIRKeyCode line:483 breturn false

fore uup IRKey [0xff]

BootMode=0

search ....

waldo msIR_GetIRKeyCode line:483 breturn false

fore uup IRKey [0xff]

BootMode=0

search ....

waldo msIR_GetIRKeyCode line:483 breturn false

fore uup IRKey [0xff]

BootMode=0

search ....

waldo msIR_GetIRKeyCode line:483 breturn false

fore uup IRKey [0xff]

BootMode=0

[ztebsp] BootMode=0

[do_bootcheck,1204][ZTEWatchdog]PATCH FOR zte BEGIN

[do_bootcheck,1208][ZTEWatchdog] Watchdog_enable TRUE

[do_bootcheck,1214][ZTEWatchdog] Watchdog start, MAXTIME 120

create instance at 52ef9bb0 with private size 256 bytes at 52ef9bf8

MDrv_PNL_Init u32PnlRiuBaseAddr = 1f200000

MDrv_PNL_Init u32PMRiuBaseAddr = 1f000000

PNL:[MDrv_PNL_SetPanelType][613]

[_MDrv_PNL_Init_LPLL][323]pstPanelInitData->u16Width=1280, pstPanelInitData->u16Height=720

[_MDrv_PNL_Init_LPLL][325]u16HTotal=1980,u16VTotal=750,pstPanelInitData->u16HTotal=1980,pstPanelInitData->u16VTotal=750, u16DefaultVFreq=500

[_MDrv_PNL_Init_Output_Dclk][369]pstPanelInitData->u16Width=1280, pstPanelInitData->u16Height=720

[_MDrv_PNL_Init_Output_Dclk][371]u16HTotal=1980,u16VTotal=750,pstPanelInitData->u16HTotal=1980,pstPanelInitData->u16VTotal=750, u16DefaultVFreq=500

PNL:CalculateLPLLSETbyDClk u32KHz = 742500000, u64DefaultLdHz = 742500000

PNL:CalculateLPLLSETbyDClk u32LpllSet = 3531df

[MApi_XC_MLG_GetStatus, 1603]No instance existed, please get an instance by calling MApi_XC_Init() first

msHdmitx_Disp_Init

create instance at 52ef9d00 with private size 1720 bytes at 52ef9d48

[XC,Version]

no need to patchcreate instance at 52efa948 with private size 80 bytes at 52efa990

Rx Support HDMI mode!

setHDMITxAnalogTuning: Error: MApi_HDMITx_GetRxDCInfoFromEDID EDID is not ready, at 262

shift -8 pixels in PAL mode

Create Dolby single part name task failed!![Hal_VE_Set_PreHSD][1826] ERROR!!! HVSD H input = 0, HVSD H output = 720

[Hal_VE_Set_PreVSD][2002] ERROR!!! HVSD V input = 0, HVSD V output = 576

[Hal_VE_EnableDI][2110] bEnable = 0, bIsDNR2VE = 0

lyndon Hal_VE_Set_PreVSD 1mmc change mount : tvcustomer

Size of file "/720.jpg" from mmc device 0 partition tvcustomer: 98879 bytes

Loading file "/720.jpg" at offset 0x0 from mmc device 0 partition tvcustomer

98879 bytes read

create instance at 52efa9e8 with private size 304 bytes at 52efaa30

[AT][MB][JPD Decode][2590]

[UTOPIA INFO] close moduleNames[35]: MODULE_NJPEG_EX

create instance at 52efa9e8 with private size 132280 bytes at 52efaa30

[GOP INFO] gop opencreate instance at 52f1aef0 with private size 6908 bytes at 52f1af38

[AT][MB][Show Logo][2627]

mxy--> ir_recovery is 0

mxy: ir_recovery is 0...

## Booting kernel from Legacy Image at 25000800 ...

Image Name:   MStar-linux

Image Type:   ARM Linux Multi-File Image (uncompressed)

Data Size:    5317562 Bytes = 5.1 MiB

Load Address: 20208000

Entry Point:  20208000

Contents:

Image 0: 4627176 Bytes = 4.4 MiB

Image 1: 690374 Bytes = 674.2 KiB

## Loading init Ramdisk from multi component Legacy Image at 25000800 ...

-usb_stop(USB_PORT0)

-usb_stop(USB_PORT1)

-usb_stop(USB_PORT2)

Loading Multi-File Image ... OK

[AT][MB][start kr][2873]

Starting kernel   ...

[PROTECT ERROR], not expected dram size: 0x0

#######################################################################

# [PROTECT WARNING], miu kernel protect is not enabled on second dram #

#######################################################################

Uncompressing Linux... done, booting the kernel.

KERN-3.10.23.001049551

tommy: thread_info_cache_init

mtdoops: mtd device (mtddev=name/number) must be supplied

[drivers/mstar2/drv/emac/mdrv_emac.c MDev_EMAC_HW_init 2196] ready init mutex

[drivers/mstar2/drv/emac/mdrv_emac.c MDev_EMAC_HW_init 2197] after init mutex

RBQP_BASE = 51a04000

init: /init.clippers.rc: 455: ignored duplicate definition of service 'mdnsd'

init: /zte_init.rc: 34: ignored duplicate definition of service 'IptvQosServ'

init: /zte_init.rc: 40: ignored duplicate definition of service 'xiriservice'

init: /zte_init.rc: 50: ignored duplicate definition of service 'softdetector'

init: ## ProductID: strlen (32)!

healthd: No charger supplies found

init: cannot find '/system/bin/xiriservice_ChinaMobile_SiChuan', disabling 'bluetoothd'

init: cannot find '/system/bin/bleservice', disabling 'bleservice'

init: cannot find '/data/data/com.android.smart.terminal.dplatform/bin/IptvQosServ', disabling 'IptvQosServ'

init: cannot find '/system/bin/stratky.sh', disabling 'stratky'

init: cannot find '/system/bin/startsoftdetector.sh', disabling 'softdetector'