华三交换机irf堆叠配置
2024-04-21 12:41:59
两台交换机堆叠
注意事项：
1、推荐使用万兆口进行堆叠
2、配置完成后需要用命令"irf-port-configuration active"激活
3、实际操作中，先配置完，最后进行插线缆
Core1配置：
[Core1]int range Ten-GigabitEthernet 1/0/49 to Ten-GigabitEthernet 1/0/52
[Core1-if-range]shutdown[Core1]irf member 1 priority 5
[Core1]irf-port 1/1 //创建irf虚拟接口
[Core1-irf-port1/1]port group interface Ten-GigabitEthernet 1/0/49 //irf虚拟接口与物理端口绑定
You must perform the following tasks for a successful IRF setup:
Save the configuration after completing IRF configuration.
Execute the "irf-port-configuration active" command to activate the IRF ports.
//为了成功设置IRF，你必须执行以下任务:
//完成IRF配置后，请保存配置。
//执行“IRF -port-configuration active”命令激活IRF端口。
[Core1-irf-port1/1]port group interface Ten-GigabitEthernet 1/0/50
[Core1-irf-port1/1]port group interface Ten-GigabitEthernet 1/0/51
[Core1-irf-port1/1]port group interface Ten-GigabitEthernet 1/0/52
[Core1-irf-port1/1]qu
[Core1]irf-port-configuration active
[Core1][Core1]int range Ten-GigabitEthernet 1/0/49 to Ten-GigabitEthernet 1/0/52
[Core1-if-range]undo shutdown
Core2配置：
[Core2]irf member 1 renumber 2
Renumbering the member ID may result in configuration change or loss. Continue?[Y/N]:y
Please reboot the device for the new member ID to take effect.
//重命名成员标号后需要重启[Core2]int range Ten-GigabitEthernet 2/0/49 to Ten-GigabitEthernet 2/0/52
[Core2-if-range]shutdown
[Core2-if-range]qu[Core2]irf member 2 priority 1
[Core2]irf-port 2/2
[Core2-irf-port2/2]port group interface Ten-GigabitEthernet 2/0/49
You must perform the following tasks for a successful IRF setup:
Save the configuration after completing IRF configuration.
Execute the "irf-port-configuration active" command to activate the IRF ports.
[Core2-irf-port2/2]port group interface Ten-GigabitEthernet 2/0/50
[Core2-irf-port2/2]port group interface Ten-GigabitEthernet 2/0/51
[Core2-irf-port2/2]port group interface Ten-GigabitEthernet 2/0/52
[Core2-irf-port2/2]qu
[Core2]
[Core2]irf-port-configuration active[Core2]int range Ten-GigabitEthernet 2/0/49 to Ten-GigabitEthernet 2/0/52
[Core2-if-range]shutdownirf配置成功
[Core1]%Nov 1 23:31:30:623 2021 Core1 DEV/2/BOARD_STATE_FAULT: Board state changed to Fault on slot 2, type is unknown.
%Nov 1 23:31:32:327 2021 Core1 DEV/5/BOARD_STATE_NORMAL: Board state changed to Normal on slot 2, type is H3C S6850.
%Nov 1 23:31:54:977 2021 Core1 LLDP/6/LLDP_CREATE_NEIGHBOR: Nearest bridge agent neighbor created on port Ten-GigabitEthernet1/0/49 (IfIndex 50), neighbor's chassis ID is 8878-15d6-0500, port ID is Ten-GigabitEthernet2/0/49.
%Nov 1 23:31:54:978 2021 Core1 LLDP/6/LLDP_CREATE_NEIGHBOR: Nearest bridge agent neighbor created on port Ten-GigabitEthernet1/0/50 (IfIndex 51), neighbor's chassis ID is 8878-15d6-0500, port ID is Ten-GigabitEthernet2/0/50.
%Nov 1 23:31:54:803 2021 Core1 LLDP/6/LLDP_CREATE_NEIGHBOR: -Slot=2; Nearest bridge agent neighbor created on port Ten-GigabitEthernet2/0/49 (IfIndex 178), neighbor's chassis ID is 8878-15d6-0500, port ID is Ten-GigabitEthernet1/0/49.
%Nov 1 23:31:54:804 2021 Core1 LLDP/6/LLDP_CREATE_NEIGHBOR: -Slot=2; Nearest bridge agent neighbor created on port Ten-GigabitEthernet2/0/50 (IfIndex 179), neighbor's chassis ID is 8878-15d6-0500, port ID is Ten-GigabitEthernet1/0/50.
%Nov 1 23:31:54:983 2021 Core1 LLDP/6/LLDP_CREATE_NEIGHBOR: Nearest bridge agent neighbor created on port Ten-GigabitEthernet1/0/51 (IfIndex 52), neighbor's chassis ID is 8878-15d6-0500, port ID is Ten-GigabitEthernet2/0/51.
%Nov 1 23:31:54:863 2021 Core1 LLDP/6/LLDP_CREATE_NEIGHBOR: -Slot=2; Nearest bridge agent neighbor created on port Ten-GigabitEthernet2/0/51 (IfIndex 180), neighbor's chassis ID is 8878-15d6-0500, port ID is Ten-GigabitEthernet1/0/51.
%Nov 1 23:31:55:161 2021 Core1 LLDP/6/LLDP_CREATE_NEIGHBOR: Nearest bridge agent neighbor created on port Ten-GigabitEthernet1/0/52 (IfIndex 53), neighbor's chassis ID is 8878-15d6-0500, port ID is Ten-GigabitEthernet2/0/52.
%Nov 1 23:31:55:064 2021 Core1 LLDP/6/LLDP_CREATE_NEIGHBOR: -Slot=2; Nearest bridge agent neighbor created on port Ten-GigabitEthernet2/0/52 (IfIndex 181), neighbor's chassis ID is 8878-15d6-0500, port ID is Ten-GigabitEthernet1/0/52.查看irf:
<Core1>dis irf
MemberID Role Priority CPU-Mac Description*+1 Master 5 8878-15d6-0504 ---2 Standby 1 8878-1aae-0604 ---
--------------------------------------------------* indicates the device is the master.+ indicates the device through which the user logs in.
//“*”表示主设备
//“+”表示用户登录的设备。The bridge MAC of the IRF is: 8878-15d6-0500Auto upgrade : yesMac persistent : 6 minDomain ID : 0查看接口：
<Core1>dis int b
Brief information on interfaces in route mode:
Link: ADM - administratively down; Stby - standby
Protocol: (s) - spoofing
Interface Link Protocol Primary IP Description
InLoop0 UP UP(s) --
MGE0/0/0 DOWN DOWN --
NULL0 UP UP(s) --
REG0 UP -- --Brief information on interfaces in bridge mode:
Link: ADM - administratively down; Stby - standby
Speed: (a) - auto
Duplex: (a)/A - auto; H - half; F - full
Type: A - access; T - trunk; H - hybrid
Interface Link Speed Duplex Type PVID Description
FGE1/0/53 DOWN 40G A A 1
FGE1/0/54 DOWN 40G A A 1
FGE2/0/53 DOWN 40G A A 1
FGE2/0/54 DOWN 40G A A 1
GE1/0/1 DOWN auto F A 1
GE1/0/2 DOWN auto F A 1
GE1/0/3 DOWN auto F A 1
GE1/0/4 DOWN auto F A 1
GE1/0/5 DOWN auto F A 1
GE1/0/6 DOWN auto F A 1
GE1/0/7 DOWN auto F A 1
GE1/0/8 DOWN auto F A 1
GE1/0/9 DOWN auto F A 1
GE1/0/10 DOWN auto F A 1
GE1/0/11 DOWN auto F A 1
GE1/0/12 DOWN auto F A 1
GE1/0/13 DOWN auto F A 1
GE1/0/14 DOWN auto F A 1
GE1/0/15 DOWN auto F A 1
GE1/0/16 DOWN auto F A 1
GE1/0/17 DOWN auto F A 1
GE1/0/18 DOWN auto F A 1
GE1/0/19 DOWN auto F A 1
GE1/0/20 DOWN auto F A 1
GE1/0/21 DOWN auto F A 1
GE1/0/22 DOWN auto F A 1
GE1/0/23 DOWN auto F A 1
GE1/0/24 DOWN auto F A 1
GE1/0/25 DOWN auto F A 1
GE1/0/26 DOWN auto F A 1
GE1/0/27 DOWN auto F A 1
GE1/0/28 DOWN auto F A 1
GE1/0/29 DOWN auto F A 1
GE1/0/30 DOWN auto F A 1
GE1/0/31 DOWN auto F A 1
GE1/0/32 DOWN auto F A 1
GE1/0/33 DOWN auto F A 1
GE1/0/34 DOWN auto F A 1
GE1/0/35 DOWN auto F A 1
GE1/0/36 DOWN auto F A 1
GE1/0/37 DOWN auto F A 1
GE1/0/38 DOWN auto F A 1
GE1/0/39 DOWN auto F A 1
GE1/0/40 DOWN auto F A 1
GE1/0/41 DOWN auto F A 1
GE1/0/42 DOWN auto F A 1
GE1/0/43 DOWN auto F A 1
GE1/0/44 DOWN auto F A 1
GE1/0/45 DOWN auto F A 1
GE1/0/46 DOWN auto F A 1
GE1/0/47 DOWN auto F A 1
GE1/0/48 DOWN auto F A 1
GE2/0/1 DOWN auto F A 1
GE2/0/2 DOWN auto F A 1
GE2/0/3 DOWN auto F A 1
GE2/0/4 DOWN auto F A 1
GE2/0/5 DOWN auto F A 1
GE2/0/6 DOWN auto F A 1
GE2/0/7 DOWN auto F A 1
GE2/0/8 DOWN auto F A 1
GE2/0/9 DOWN auto F A 1
GE2/0/10 DOWN auto F A 1
GE2/0/11 DOWN auto F A 1
GE2/0/12 DOWN auto F A 1
GE2/0/13 DOWN auto F A 1
GE2/0/14 DOWN auto F A 1
GE2/0/15 DOWN auto F A 1
GE2/0/16 DOWN auto F A 1
GE2/0/17 DOWN auto F A 1
GE2/0/18 DOWN auto F A 1
GE2/0/19 DOWN auto F A 1
GE2/0/20 DOWN auto F A 1
GE2/0/21 DOWN auto F A 1
GE2/0/22 DOWN auto F A 1
GE2/0/23 DOWN auto F A 1
GE2/0/24 DOWN auto F A 1
GE2/0/25 DOWN auto F A 1
GE2/0/26 DOWN auto F A 1
GE2/0/27 DOWN auto F A 1
GE2/0/28 DOWN auto F A 1
GE2/0/29 DOWN auto F A 1
GE2/0/30 DOWN auto F A 1
GE2/0/31 DOWN auto F A 1
GE2/0/32 DOWN auto F A 1
GE2/0/33 DOWN auto F A 1
GE2/0/34 DOWN auto F A 1
GE2/0/35 DOWN auto F A 1
GE2/0/36 DOWN auto F A 1
GE2/0/37 DOWN auto F A 1
GE2/0/38 DOWN auto F A 1
GE2/0/39 DOWN auto F A 1
GE2/0/40 DOWN auto F A 1
GE2/0/41 DOWN auto F A 1
GE2/0/42 DOWN auto F A 1
GE2/0/43 DOWN auto F A 1
GE2/0/44 DOWN auto F A 1
GE2/0/45 DOWN auto F A 1
GE2/0/46 DOWN auto F A 1
GE2/0/47 DOWN auto F A 1
GE2/0/48 DOWN auto F A 1
XGE1/0/49 UP 10G F -- --
XGE1/0/50 UP 10G F -- --
XGE1/0/51 UP 10G F -- --
XGE1/0/52 UP 10G F -- --
XGE2/0/49 UP 10G F -- --
XGE2/0/50 UP 10G F -- --
XGE2/0/51 UP 10G F -- --
XGE2/0/52 UP 10G F -- --华三交换机irf堆叠配置相关推荐
- 华三交换机IRF堆叠配置及MAD配置
华三交换机IRF堆叠配置及MAD配置 1.主机 2.备机 3.MAD检测(使用BFD方式) 1.主机 irf member 1 priority 32 //将主机IRF优先级调高,指定该台设备为主机 ...
- 华三交换机irf 堆叠配置_交换机的堆叠配置
交换机堆叠技术 交换机堆叠,通俗讲就是将多台交换机"合体",堆叠后的交换机从逻辑上可视作一台交换机.目前各大网络厂商分别拥有各自的交换机堆叠技术,比如华为的iStack(Intel ...
- 华三交换机irf 堆叠配置_H3C S5500-EI IRF堆叠的典型配置
H3C S5500-EI IRF堆叠的典型配置 一.组网需求: 配置三台S5500-EI交换机进行链型堆叠,并分别配置成员编号为1.2.3.线缆连接方式如图所示 二.组网图: 三.配置步骤: (1)三 ...
- 【网络】华三交换机irf堆叠配置举例
1.irf堆叠介绍 IRF(Intelligent Resilient Framework,智能弹性架构)是 H3C 自主研发的软件虚拟化技术,通过 将多台设备虚拟为一台设备,可以简化网络拓扑,提高管 ...
- 华三交换机irf堆叠配置方法
配置步骤 一. 配置IRF 配置设备编号 # 设备 A保留缺省编号为1,不需要进行配置.同时,在设备 B上将设备的成员编号修改为2. <设备B> system-view [设备B] irf ...
- 华三交换机irf 堆叠配置_H3C交换机堆叠的基本配置
刚刚新建了一口深信服aDesk桌面云机房,其中用于接入的两台交换机是H3C的5130S-EI.两台交换机采用堆叠方式,堆叠之后将四个光口做链路聚合上联至汇聚交换机. 由于以前接触的H3C交换机都是基于 ...
- 华三交换机irf堆叠以及BFD检测配置
环境: 两台交换机 bfd检测VLAN 配置irf堆叠 Switch-1: [H3C]sysname irf-1 修改名字 [irf-1]irf member 1 priority 10 ...
- 华三交换机IRF堆叠 典型配置
将三台交换机虚拟成一台交换机,以此实现协同工作,便于管理 物理拓扑 注意事项 1.交换机之间互联的端口不在是普通的千兆以太网网口,而是万兆以太网口,也就是图片上的XGE接口,普通的接口无法做堆叠: 2 ...
- 【华三交换机开局基础配置】
[华三交换机开局基础配置] 开局主要配置 设备命名 配置管理地址 配置远程登录 配置时区NTP 配置SNMP 配置syslog 开局主要配置 设备命名 system-view sysname xxxx ...
最新文章
- 225.用队列实现栈
- 吊打MySQL，MariaDB到底强在哪？
- 人工智能的热望与冷思考 | 郭毅可院士：我们不要神化它
- shell实例第12讲：给定目录找出包含关键字的文件
- Python入门——石头剪刀布程序
- 网络路径无法访问问题的解决
- 使用jdk DOM，SAX和第三方jar包DOM4J创建，解析xml文件
- java复制重命名,JAVA操作文件的复制和重命名失败的原因
- redis两种持久化模式
- 关于PPP认证中的PAP和CHAP原理取证与相关疑问
- Spring源码之bean的销毁registerDisposableBeanIfNecessary方法解读
- RxJava：concat（连接）、 concatDelayError、 concatEager的使用
- Unity 使用Socket 简单实现通讯
- 磁盘分区——MBR详解（私密）
- Vue中禁止鼠标滑轮事件
- 一步搞定无法审查元素
- C/C++更新linux系统时间和硬件时间的方法
- 82.android 简单的当前运行内存清理
- 螺丝螺母匹配问题（快排的变形应用）
- 步进控制薄图modbus通讯1200PLC通讯威纶通