1-NET UX1000-实战-配置-Lync Server 2010-集成

1. 实验目的

FXS Quick Start 1.1

Configuring a call for the UX1000 FXS

Use the following step to configure a UX 1000 FXS Port.

Lync 分机----呼叫---FXS分机

8288------6001

FXS分机----呼叫--- Lync 分机

6001----8288

2. 登录-UX1000

https://192.168.1.147

用户名:admin

密 码:admin

3. 验证UX版本

Verifying the UX Versions

Prerequisite! Check your software level.

Verify that your UX1000 is loaded with firmware (boot partition) 2.1.6k and software image 2.0.0v108 or better.  Older versions of

firmware/software will cause the FXS card to not function.

To begin the configuration, verify your Boot and Application versions.

3.1. 选择-Settings

3.2. 选择-System-Software Management-Boot Partition

3.3. 选择-System-Software Management-Application Partitions

Warning! Upgrade the UXSBA first.

If the UX application image requires an upgrade, always upgrade the UX Communication Service software (UXSBA) before upgrading

the UX application software. The firmware (boot) image can be upgraded either before or after the UX application software.

3.4. 验证-许可证

Verify Licensing

The system must have the FXS and DSP licenses to make calls.  Depending upon the types of calls, the Transcoding license may also be necessary.

Unlimited---无限

SIP Registrations---注册普通的SIP话机

支持注册Skype

4. 验证-FXS卡/端口状态

Verify the FXS Card/Port State

Check to ensure that the FXS card and ports are functional by checking the System Tab | Overview Tab.  The FXS Telco modules should show Activated, and the Service and Admin States should be UP.

Main Board:主板

FXS Not Activated and Up?

Did you upgrade the firmware and software?

5. 配置-UX1000 For FXS

Configuring the UX1000 for FXS

5.1. 增加-配置文件

Begin the configuration by adding a CAS Signaling Profile for FXS.

选择-Add FXS

选择-OK

首先得建立配置文件。

FXS Profile---S口的配置文件。

5.2. 增加-默认路由表

增加

Default Route Table

5.3. 增加-信令组

add a CAS Signaling Group

ISDN SG:---数字线路-信令组

SIP SG:-----IP-信令组---连接Lync Server 2010

CAS SG:----针对模拟线路，S口和O口

选择-Add CAS SG

Make sure to set the Channel Hunting to Own Number, otherwise the first free channel will answer every call (regardless of any other configuration settings).

参照:

Description:FXS Port 1

Channel Hunting:Own Number

Call Routing Table:Default Route Table

选择-OK

5.4. 分配号到-S口

Add an Assigned Channel and apply the desired phone number to the corresponding FXS port.

增加

Apply

The FXS-attached phone should now have dial-tone.

No dial-tone?

Are you certain your firmware and software are updated as noted at the beginning of these instructions?

5.5. 增加-一个FXS口呼叫的交换

Lync > FXS

FXS > PSTN

5.6. Lync 服务器

SIP

Add

Signaling Groups

5.7. 路由表

注意---更正---Lync > FXS

注意转换规则:

Lync > FXS

应用

应用

5.8. 测试

Lync---FXS

8288---6001

FXS---Lync

6001---8288

5.9.

6. 安装-jre-6u30-windows-i586-s.exe

7. 监控-通话

访问-NET UX1000

https://192.168.1.147

admin

admin

R是S口那边没挂断，正常挂断后不是这个样子。是绿色。

8. 安装-NET LX 2.8

NET LX 2.8---日志管理

9. UX1000-设置

10. 日志管理

10.1.打开-管理平台

10.2.选择-Syslog Server

10.3.选择-Start Listering

10.4.Lync分机---呼叫---FXS口

8288---》---6001

10.5.接听

10.6.选择-Stop Listering

10.7.选择-分析

10.8.

11. Lync分机---呼叫---FXS口分机

11.1.SIP

SIP Server Tables

填写:

Lync Server 2010-服务器

192.168.1.82 5068

SIP Options

11.2.CAS

新建-FXS---分机配置文件

FXS Profile

11.3.Signaling Groups

信令组

CAS SG CAS信令组

写入FXS口---分机号

SIP SG SIP信令组

写入 SIP服务器

FX0---也需要建信令组.需实战

E1----也需要建信令组.需实战

11.4.Transformation

转换规则

11.5.Call Routing Table

本文转自 CTO_LiuJinFeng 51CTO博客，原文链接：http://blog.51cto.com/dynamic/767106，如需转载请自行联系原作者