各厂家网络设备查看端口收发光功率-命令汇总
年底了,博猪很懒,半年都没写几篇像样的技术文章,今天抽风,汇总一下不同厂家设备的端口收发光命令吧,工程上经常用到,也经常容易忘记,备忘。
本文记录的设备型号有:cisco CRS、7609、Nexus7K、华为NE5000E、9312、8512、H3C 12508、中兴8905、Juniper EX8208、上海贝尔(阿尔卡特)OS10K、SR7750。
型号:思科CRS-1 系统版本:IOS XR , Version 4.0.4
CRS-1#show controllers SONET 0/0/1/0
<…>Optical Power Monitoring (accuracy: +/- 1dB)Rx power = 0.0828 mW, -10.8 dBmTx power = 1.0288 mW, 0.1 dBmTx laser current bias = 68.3 mA!<---------POS口
CRS-1#show hw-module subslot 0/10/0 status pluggable-optics 0
SPA 0/10/0 device pluggable-optics 0/0 info:
int Tengige/10/0/0: State: EnabledEnvironmental Information - raw valuesTemperature: 8602Tx voltage: 0 in units of 100uVoltTx bias: 63000 uATx power: 0 dBm (10180 in units of 0.1 uW)Rx power: -9 dBm (1126 in units of 0.1 uW)(AUX1) +3.3V Supply Voltage: 32324
!<---------GE口
型号:思科7609
7609#show interfaces te1/1 transceiver
Optical OpticalTemperature Voltage Current Tx Power Rx Power
Port (Celsius) (Volts) (mA) (dBm) (dBm)
---------- ----------- ------- -------- -------- --------
Te1/1 40.3 N/A 83.6 -- 1.9 -14.3
型号:思科Nexus7010
N7K#show interface e3/1 transceiver details
SFP Detail Diagnostics Information (internal calibration)
----------------------------------------------------------------------------Current Alarms WarningsMeasurement High Low High Low
----------------------------------------------------------------------------
Temperature 24.08 C 90.00 C -10.00 C 85.00 C -5.00 C
Voltage 3.27 V 3.59 V 3.00 V 3.50 V 3.09 V
Current 6.79 mA 15.00 mA 1.00 mA 12.00 mA 2.00 mA
Tx Power 15.03 dBm 20.00 dBm 6.50 dBm 17.00 dBm 10.49 dBm
Rx Power 12.35 dBm 23.00 dBm -1.02 dBm 20.00 dBm 3.01 dBm
型号:华为NE5000E
NE5000E#display interface pos 1/6/0/0
<…>
Rx Optical Power: -3.62dBm, Tx Optical Power: -2.25dBm
Physical layer is Packet Over SDH
Scramble enabled, clock master, CRC-32, loopback: none
Flag J0 "NetEngine "
Flag J1 "NetEngine "
Flag C2 22(0x16)SDH alarm:section layer: noneline layer: nonepath layer: noneSDH error:section layer: B1 0line layer: B2 0 REI 0 path layer: B3 0 REI 0
<…>
!<---------POS口
NE5000E#display interface gi1/8/0/1
<..>
WaveLength: 1310nm, Transmission Distance: 10km
Rx Optical Power: -5.06dBm, Tx Optical Power: -2.01dBm
Loopback:none, LAN full-duplex mode, Pause Flowcontrol:Receive Enable and Send Enable
<..>
!<-------GE口
型号:华为9312
S9312#display transceiver interface XGigabitEthernet 1/1/0/0 verbose
<…>
-------------------------------------------------------------
Diagnostic information:Temperature(¡ãC) :35Voltage(V) :3.31Bias Current(mA) :6.52Bias High Threshold(mA) :10.00Bias Low Threshold(mA) :2.60Current Rx Power(dBM) :-3.12Default Rx Power High Threshold(dBM) :1.50Default Rx Power Low Threshold(dBM) :-14.00Current Tx Power(dBM) :-2.10Default Tx Power High Threshold(dBM) :-1.00Default Tx Power Low Threshold(dBM) :-8.00User Set Rx Power High Threshold(dBM) :1.50User Set Rx Power Low Threshold(dBM) :-14.00User Set Tx Power High Threshold(dBM) :-1.00User Set Tx Power Low Threshold(dBM) :-8.00
-------------------------------------------------------------
型号:华为8512
S8512#display fiber-module GigabitEthernet 0/1/1
GigabitEthernet0/1/1 transceiver information:Transceiver Type : 10G_LR_SM_LCConnector Type : LCWavelength(nm) : 1310Transfer Distance : 10km(SMF)Digital Diagnostic Monitoring : YESVendor Name : FINISAR CORP. TX Power : -2.0dBMRX Power : -2.5dBM
型号:H3C 12508
H3C12508#display transceiver diagnosis interface te3/0/1
Ten-GigabitEthernet3/0/1 transceiver diagnostic information:Current diagnostic parameters:Temp.(°C) Voltage(V) Bias(mA) RX power(dBM) TX power(dBM)30 3.36 30.10 -1.45 -2.01
型号:Juniper EX8208
EX8208>show interfaces diagnostics optics xe-0/0/1
Physical interface: xe-0/0/1Laser bias current : 37.996 mALaser output power : 0.6900 mW / -1.61 dBmModule temperature : 30 degrees C / 86 degrees FModule voltage : 3.2990 VReceiver signal average optical power : 0.5150 mW / -2.88 dBm
<…>
型号:中兴8905 系统版本:V3.00.02.B10
ZXR10(config)#interface xgei-0/1/0/2
ZXR10(config-if)#optical-inform monitor enable
ZXR10#show optical-inform brief interface xgei-0/1/0/2
If device is externally calibrated, only calibrated values are printed.
-Inf: not applicable, Tx: transmit, Rx: receive.Optical Optical
Interface Temperature Voltage Voltage Current Tx Power Rx Power
Name (Celsius) (3.3 Volts)(5 Volts) (mA) (dBm) (dBm)
--------------------------------------------------------------------------------
xgei-0/1/0/2 33.20 3.27 N/A 54.01 1.87 -10.72
型号:上海贝尔Omniswitch 10K
OS10K>interfaces ddm enable
OS10K>show interfaces port 3/1 ddm
Slot/ Thres- Temp Voltage Tx Bias Output InputPort hold (C) (V) (mA) (dBm) (dBm)
----------+--------+----------+------------+------------+------------+------------3/1 Actual 21.0 3.258 4.136 -5.969 -6.719 A-High 100.0 3.600 40.000 1.000 3.486 W-High 90.0 3.500 30.000 0.000 2.486 W-Low 0.0 3.100 1.000 -9.500 -12.518 A-Low -5.0 3.000 0.500 -10.501 -13.516
型号:阿尔卡特(贝尔)SR 7750
SR7750#show port 1/1/1 detail | match DDM post-lines 10
Last Cleared Time : 10/25/2012 15:54:54 DDM Events : Enabled
Configured Mode : network Encap Type : null
Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100
PBB Ethertype : 0x88e7
Ing. Pool % Rate : 100 Egr. Pool % Rate : 100
Ing. Pool Policy : n/a
Egr. Pool Policy : n/a
Net. Egr. Queue Pol: default
Egr. Sched. Pol : n/a
Auto-negotiate : N/A MDI/MDX : N/A
Transceiver Digital Diagnostic Monitoring (DDM)
===============================================================================Value High Alarm High Warn Low Warn Low Alarm
-------------------------------------------------------------------------------
Temperature (C) +28.8 +83.0 +80.0 -10.0 -13.0
Tx Bias Current (mA) 37.9 80.0 75.0 20.0 15.0
Tx Output Power (dBm) -1.97 1.50 1.00 -6.00 -7.00
Rx Optical Power (avg dBm) -3.11 2.50 2.00 -18.01 -20.00
Aux1: 3.3 Voltage (V) 3.29 3.63 3.50 3.10 3.00
===============================================================================
本文固定链接: http://www.opsunny.com/each-manufacturer-received-glowing-power-networking-device-to-view-port-command-summary/ | OPSUNNY BLOG
各厂家网络设备查看端口收发光功率-命令汇总相关推荐
- 思科、华为、瞻博juniper、中兴、阿尔卡特中高端网络设备查看端口收发光功率-命令汇总
博猪很懒,半年都没写几篇像样的技术文章,今天抽风,汇总一下不同厂家设备的端口收发光命令吧,工程上经常用到,也经常容易忘记,备忘. 本文记录的设备型号有:cisco CRS.7609.Nexus7K.华 ...
- linux查看server端口占用,Linux查看端口占用的命令
Linux查看端口占用的命令 apt-get install lsof lsof -i:端口号 lsof常用命令 lsof -i:8080:查看8080端口占用 lsof abc.txt:显示开启文件 ...
- 华三交换机镜像配置命令_H3C交换机端口镜像配置命令汇总
H3C交换机端口镜像配置命令汇总 一.端口镜像概念: Port Mirror(端口镜像)是用于进行网络性能监测.可以这样理解:在端口A 和端口B 之间建立镜像关系,这样,通过端口A 传输的数据将同时复 ...
- Linux查看端口号相关命令
学习内容:Linux端口号相关命令 仅自己学习记录!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 端口相关概念: 在网络技术中,端口(Port)包括逻辑端口和物理端口 ...
- shell命令查阅端口信息_linux查看端口状态相关命令
netstat netstat 命令应用是比较频繁的,比如查看端口占用啦,查看端口进程啦,这些时候都是有必要的. netstat命令各个参数说明如下: -t : 指明显示TCP端口 -u : 指明显示 ...
- 中兴网络设备查看电源状态检查命令
描述:中兴网络设备查看风扇状态电源状态检查命令 命令: show power
- 查看端口被占用命令(Windows+Linux)
以8081端口为例,查看端口占用情况 一.Windows版: 1.开始--运行--cmd 进入命令提示符, 2.输入netstat -ano 查看所有端口连接对应的PID , C:\>netst ...
- linux常用的20个命令查看端口,Linux常用命令-查看端口使用具体情况
签名:松月生夜凉,风泉满清听 静思语:人生之贵,莫贵于信,信乃人生立世之本! Latest posts by 折月煮酒 查看端口使用具体情况 Linux 查看端口占用情况 Linux 查看端口占用情况 ...
- 查看端口号的命令,android SDK启动模拟器的方法
1.查看端口port号的命令:netstat -ano 2.通过android SDK启动android 模拟器的方法:
最新文章
- Jittor 的Op, Var算子
- Rust 所有权介绍
- 里程碑:BCH网络出现首例Schnorr Multisig交易
- MSB600 cmd.exe 已退出,代码为3
- 'module' object has no attribute 'scalar_summary'
- NYOJ 1186 心理阴影(两个圆环的相交面积)
- xcode 插件安装路径
- 18. 爱吃皮蛋的小明(斐波那契数列)
- php dlt645,RT-Thread-Mirror
- window 服务(三)
- 【FPGA入门一】一个简单的LED流水灯
- VS配置arduino环境
- 应该怎样读TAOCP
- L-ScanPort2.0beta版+完整源代码
- 批量添加文件名前后缀的工具_艾孜尔江撰
- couldn't create PTY
- ss terminal下客户端sslocal+proxychains或者privoxy
- lopa分析_保护层分析(LOPA)
- 【算法设计与分析】分支限界法解决单源最短路径问题:输入带权图G=(V,E)以及出发顶点s,然后用分支限界法解决问题,要求输出路径和长度以及计算时间;
- CodeForces - 1004B - Sonya and Exhibition(纯思维题)