QQ图片20180517100932.png

第一次编译的固件，失败！

Boot and Recovery Environment for Embedded Devices
Copyright (C) 2018 HackPascal <hackpascal@gmail.com>
Build date 2018-03-23 [git-994feec]
Version 1.1 (r1211)DRAM: 32MB
Platform: Qualcomm Atheros QCA953X rev 2
Board: Generic board
Clocks: CPU: 550MHz, DDR: 400MHz, AHB: 200MHz, Ref: 25MHz
Flash: Macronix MX25L6435E (8MB) on ath79-spi
ag71xx-eth: MAC address is invalid, using default settings.
ag71xx-eth: Using MAC address 00:13:74:00:00:01
Waiting for auto-negotiation complete ... OK
eth0: Atheros AR8228/AR8229 rev 1Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0Press any key to interrupt autoboot ... 2
Autoboot aborted due to button press.Starting breed built-in shellbreed>
breed>
breed>
breed> boot
Usage:boot mem <addr>   - Boot from memory address or memory-mapped addressboot flash [bank <n>] <addr>   - Boot from flashboot linux <addr> - Boot linux kernel at <addr>boot raw <addr>   - Disable interrupts and jump to <addr>boot breed <addr> - Boot given breed file at <addr>breed> boot flash
Usage:boot mem <addr>   - Boot from memory address or memory-mapped addressboot flash [bank <n>] <addr>   - Boot from flashboot linux <addr> - Boot linux kernel at <addr>boot raw <addr>   - Disable interrupts and jump to <addr>boot breed <addr> - Boot given breed file at <addr>breed> reboot
Unrecognised command: reboot
Type 'help' to get available commands.breed> ps
Unrecognised command: ps
Type 'help' to get available commands.breed> help
Available commands:
about    - About this bootloader
abstatus - Interrupt status of autoboot
arp      - Display ARP table
autoboot - Detect firmware type and boot automatically
boot     - Boot firmware
btntst   - Test GPIO of buttons
dhcp     - Display DHCP leases
env      - Environment variables utility
envconf  - Configure environment variable block
exit     - Exit from telnet
flash    - Flash utility
gpio     - GPIO utilities
help     - Show available commands
mdio     - MDIO utility
mem      - Memory operation utilities
net      - Network control
netstat  - Display network state
reset    - Restart device
setbrg   - Set baudrate
spi      - SPI utility
sysinfo  - Display system information
thread   - Display all threads
wget     - Retrieval file through HTTPbreed> autoboot
Trying to boot firmware from 0x9f680000 ...
U-Boot firmware image header detected.Image Name:   MIPS OpenWrt Linux-3.3.8Data Size:    1026203 BytesLoad Address: 80060000Entry Point:  80060000
Uncompressing data (LZMA) ... done.
Flushing cache ... done.Starting kernel at 0x80060000...[    0.000000] Linux version 3.3.8 (hades@hades) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Wed May 16 16:16:25 CST 2018
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Qualcomm Atheros QCA9531 rev 2
[    0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00002000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00002000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=AP143 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,6336k(rootfs),1472k(kernel),64k(art),7744k@0x50000(firmware) rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00037fd0
[    0.000000] Readback ErrCtl register=00037fd0
[    0.000000] Memory: 28936k/32768k available (2169k kernel code, 3832k reserved, 563k data, 176k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:83
[    0.000000] Calibrating delay loop... 366.18 BogoMIPS (lpj=1830912)
[    0.060000] pid_max: default: 32768 minimum: 301
[    0.060000] Mount-cache hash table entries: 512
[    0.070000] Initialized recycle list for cpu 0.
[    0.070000] NET: Registered protocol family 16
[    0.080000] gpiochip_add: registered GPIOs 0 to 17 on device: ath79
[    0.080000] MIPS: machine is Qualcomm Atheros AP143 reference board
[    0.090000] ar71xx: invalid MDIO id 1
[    0.500000] bio: create slab <bio-0> at 0
[    0.510000] Switching to clocksource MIPS
[    0.520000] NET: Registered protocol family 2
[    0.520000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.520000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.530000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.530000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.540000] TCP reno registered
[    0.540000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.550000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.560000] NET: Registered protocol family 1
[    0.580000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.580000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.590000] msgmni has been set to 56
[    0.600000] io scheduler noop registered
[    0.600000] io scheduler deadline registered (default)
[    0.610000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.640000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.640000] console [ttyS0] enabled, bootconsole disabled
[    0.640000] console [ttyS0] enabled, bootconsole disabled
[    0.660000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[    0.660000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[    0.670000] 6 cmdlinepart partitions found on MTD device spi0.0
[    0.670000] Creating 6 MTD partitions on "spi0.0":
[    0.680000] 0x000000000000-0x000000040000 : "u-boot"
[    0.690000] 0x000000040000-0x000000050000 : "u-boot-env"
[    0.690000] 0x000000050000-0x000000680000 : "rootfs"
[    0.700000] mtd: partition "rootfs" set to be root filesystem
[    0.710000] mtd: partition "rootfs_data" created automatically, ofs=60000, len=620000
[    0.710000] 0x000000060000-0x000000680000 : "rootfs_data"
[    0.720000] 0x000000680000-0x0000007f0000 : "kernel"
[    0.730000] 0x0000007f0000-0x000000800000 : "art"
[    0.730000] 0x000000050000-0x0000007e0000 : "firmware"
[    0.770000] ag71xx_mdio: probed
[    0.900000] ag71xx_mdio: probed
[    0.910000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.470000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[    1.480000] eth1: Atheros AG71xx at 0xba000000, irq 5
[    2.030000] eth1: Found an AR934X built-in switch
[    3.070000] TCP cubic registered
[    3.070000] NET: Registered protocol family 17
[    3.080000] 8021q: 802.1Q VLAN Support v1.8
[    3.080000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    3.090000] Freeing unused kernel memory: 176k freed
[    3.100000] Kernel panic - not syncing: No init found.  Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.

qsdk 修改后再次编译，


Boot and Recovery Environment for Embedded Devices
Copyright (C) 2018 HackPascal <hackpascal@gmail.com>
Build date 2018-03-23 [git-994feec]
Version 1.1 (r1211)DRAM: 32MB
Platform: Qualcomm Atheros QCA953X rev 2
Board: Generic board
Clocks: CPU: 550MHz, DDR: 400MHz, AHB: 200MHz, Ref: 25MHz
Flash: Macronix MX25L6435E (8MB) on ath79-spi
ag71xx-eth: MAC address is invalid, using default settings.
ag71xx-eth: Using MAC address 00:13:74:00:00:01
Waiting for auto-negotiation complete ... OK
eth0: Atheros AR8228/AR8229 rev 1Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0Press any key to interrupt autoboot ... 2
Autoboot aborted due to button press.Starting breed built-in shellbreed> Upgrade completed.
Rebooting in 2 seconds ...
Resetting ...
Boot and Recovery Environment for Embedded Devices
Copyright (C) 2018 HackPascal <hackpascal@gmail.com>
Build date 2018-03-23 [git-994feec]
Version 1.1 (r1211)DRAM: 32MB
Platform: Qualcomm Atheros QCA953X rev 2
Board: Generic board
Clocks: CPU: 550MHz, DDR: 400MHz, AHB: 200MHz, Ref: 25MHz
Flash: Macronix MX25L6435E (8MB) on ath79-spi
ag71xx-eth: MAC address is invalid, using default settings.
ag71xx-eth: Using MAC address 00:13:74:00:00:01
Waiting for auto-negotiation complete ... OK
eth0: Atheros AR8228/AR8229 rev 1Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0Press any key to interrupt autoboot ... 2
Autoboot aborted due to button press.Starting breed built-in shellbreed> autoboot
Trying to boot firmware from 0x9f680000 ...
U-Boot firmware image header detected.Image Name:   MIPS OpenWrt Linux-3.3.8Data Size:    954963 BytesLoad Address: 80060000Entry Point:  80060000
Uncompressing data (LZMA) ... done.
Flushing cache ... done.Starting kernel at 0x80060000...[    0.000000] Linux version 3.3.8 (hades@hades) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r40331) ) #1 Fri May 18 10:33:12 CST 2018
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Qualcomm Atheros QCA9531 rev 2
[    0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00002000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00002000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=AP143 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,6336k(rootfs),1472k(kernel),64k(art),7744k@0x50000(firmware) rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00017fd0
[    0.000000] Readback ErrCtl register=00017fd0
[    0.000000] Memory: 28992k/32768k available (2191k kernel code, 3776k reserved, 437k data, 220k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:83
[    0.000000] Calibrating delay loop... 366.18 BogoMIPS (lpj=1830912)
[    0.060000] pid_max: default: 32768 minimum: 301
[    0.060000] Mount-cache hash table entries: 512
[    0.070000] Initialized recycle list for cpu 0.
[    0.070000] NET: Registered protocol family 16
[    0.080000] gpiochip_add: registered GPIOs 0 to 17 on device: ath79
[    0.090000] MIPS: machine is Qualcomm Atheros AP143 reference board
[    0.100000] ar71xx: invalid MDIO id 1
[    0.510000] bio: create slab <bio-0> at 0
[    0.520000] Switching to clocksource MIPS
[    0.530000] NET: Registered protocol family 2
[    0.530000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.530000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.540000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.540000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.550000] TCP reno registered
[    0.550000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.560000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.570000] NET: Registered protocol family 1
[    0.590000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.590000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.600000] msgmni has been set to 56
[    0.610000] io scheduler noop registered
[    0.610000] io scheduler deadline registered (default)
[    0.620000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.650000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.650000] console [ttyS0] enabled, bootconsole disabled
[    0.650000] console [ttyS0] enabled, bootconsole disabled
[    0.670000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[    0.670000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[    0.680000] 6 cmdlinepart partitions found on MTD device spi0.0
[    0.690000] Creating 6 MTD partitions on "spi0.0":
[    0.690000] 0x000000000000-0x000000040000 : "u-boot"
[    0.700000] 0x000000040000-0x000000050000 : "u-boot-env"
[    0.700000] 0x000000050000-0x000000680000 : "rootfs"
[    0.710000] mtd: partition "rootfs" set to be root filesystem
[    0.720000] mtd: partition "rootfs_data" created automatically, ofs=260000, len=420000
[    0.730000] 0x000000260000-0x000000680000 : "rootfs_data"
[    0.730000] 0x000000680000-0x0000007f0000 : "kernel"
[    0.740000] 0x0000007f0000-0x000000800000 : "art"
[    0.750000] 0x000000050000-0x0000007e0000 : "firmware"
[    0.780000] ag71xx_mdio: probed
[    0.910000] ag71xx_mdio: probed
[    0.920000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.480000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[    1.490000] eth1: Atheros AG71xx at 0xba000000, irq 5
[    2.050000] eth1: Found an AR934X built-in switch
[    3.080000] TCP cubic registered
[    3.080000] NET: Registered protocol family 17
[    3.090000] 8021q: 802.1Q VLAN Support v1.8
[    3.090000] ### of_selftest(): No testcase data in device tree; not running tests
[    3.100000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    3.110000] Freeing unused kernel memory: 220k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -
[    9.850000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[    9.850000] Backport generated by backports.git backports-20130617-4-ge3220f5
[    9.890000] cfg80211: Calling CRDA to update world regulatory domain
[    9.890000] cfg80211: World regulatory domain updated:
[    9.900000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    9.910000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.920000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.920000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    9.930000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[    9.940000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[    9.950000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[   10.180000] SCSI subsystem initialized
[   10.330000] usbcore: registered new interface driver usbfs
[   10.330000] usbcore: registered new interface driver hub
[   10.340000] usbcore: registered new device driver usb
[   10.950000] Button Hotplug driver version 0.4.1
[   11.050000] PPP generic driver version 2.4.2
[   11.150000] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[   11.270000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   11.370000] NET: Registered protocol family 24
[   11.400000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   11.400000] ehci-platform ehci-platform.0: Generic Platform EHCI Controller
[   11.410000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[   11.450000] ehci-platform ehci-platform.0: irq 3, io mem 0x1b000000
[   11.470000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[   11.470000] hub 1-0:1.0: USB hub found
[   11.480000] hub 1-0:1.0: 1 port detected
[   11.500000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
[   11.770000] Initializing USB Mass Storage driver...
[   11.780000] usbcore: registered new interface driver usb-storage
[   11.780000] USB Mass Storage support registered.Please press Enter to activate this console. BusyBox v1.19.4 (2018-05-17 18:29:38 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.MM           NM                    MMMMMMM          M       M$MMMMM        MMMMM                MMMMMMMMMMM      MMM     MMMMMMMMMMM     MM MMMMM.              MMMMM:MMMMMM:   MMMM   MMMMM
MMMM= MMMMMM  MMM   MMMM       MMMMM   MMMM  MMMMMM   MMMM  MMMMM'
MMMM=  MMMMM MMMM    MM       MMMMM    MMMM    MMMM   MMMMNMMMMM
MMMM=   MMMM  MMMMM          MMMMM     MMMM    MMMM   MMMMMMMM
MMMM=   MMMM   MMMMMM       MMMMM      MMMM    MMMM   MMMMMMMMM
MMMM=   MMMM     MMMMM,    NMMMMMMMM   MMMM    MMMM   MMMMMMMMMMM
MMMM=   MMMM      MMMMMM   MMMMMMMM    MMMM    MMMM   MMMM  MMMMMM
MMMM=   MMMM   MM    MMMM    MMMM      MMMM    MMMM   MMMM    MMMM
MMMM$ ,MMMMM  MMMMM  MMMM    MMM       MMMM   MMMMM   MMMM    MMMMMMMMMMM:      MMMMMMM     M         MMMMMMMMMMMM  MMMMMMM MMMMMMMMMMMMM       MMMMN     M           MMMMMMMMM      MMMM    MMMMMMMM          M                    MMMMMMM        M       MM---------------------------------------------------------------For those about to rock... (Attitude Adjustment, r40331)---------------------------------------------------------------
root@OpenWrt:/# [   17.080000] device eth1 entered promiscuous mode
[   17.680000] eth1: link up (1000Mbps/Full duplex)
[   17.680000] br-lan: port 1(eth1) entered forwarding state
[   17.690000] br-lan: port 1(eth1) entered forwarding state
[   19.690000] br-lan: port 1(eth1) entered forwarding stateroot@OpenWrt:/# [   31.740000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   31.740000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   31.750000] jffs2_build_filesystem(): erasing all blocks after the end marker...

qca9533 openwrt 启动信息相关推荐

  1. openWrt启动mDNS服务

    openWrt启动mDNS服务 引言:一般情况下,openwrt会自动启动mDNS服务的,但由于我刷写的镜像的问题,我的openWrt并没有启动mDNS这个守护进程.在解决这个问题的过程中遇到一些问题 ...

  2. U-Boot的启动信息和命令使用

    内容来自<[正点原子]I.MX6U嵌入式Linux驱动开发指南V1.5.2.pdf>,有删减. 启动信息 1 U-Boot 2016.03-gd3f0479 (Aug 07 2020 - ...

  3. OpenWrt启动过程分析+添加自启动脚本【转】

    一.OpenWrt启动过程分析 转自: http://www.eehello.com/?post=107 总结一下OpenWrt的启动流程:1.CFE->2.linux->3./etc/p ...

  4. asterisk1.8启动信息分析（未完）

    将main/asterisk.c的开启守护进程的那行代码修改一下,即可看到asterisk的启动打印信息. if (daemon(1, 0) < 0) 改为 if (daemon(1, 1) & ...

  5. Redis（二）：Redis的安装及配置（2）---设置启动信息

    设置启动信息 拷贝源码包中的启动脚本文件(源码包中的utils目录下)到/etc/rc.d/init.d目录下,如下图: 修改脚本信息: 执行程序(EXEC)路径就是默认的安装路径,如果我们的安装路径 ...

  6. 在配置文件web.xml中配置Struts2的启动信息

    在配置文件web.xml中配置Struts2的启动信息: <?xml version="1.0" encoding="UTF-8"?> <we ...

  7. linux 内核调试 booting the kernel.,booting the kernel后无内核启动信息的调试方法

    移植内核经常会出现 Uncompressing Linux................................................................ done, ...

  8. 嵌入式linux启动信息完全注释

    嵌入式linux启动信息完全注释 from:http://www.embedlinux.cn/ShowPost.asp?ThreadID=377 摘要 我们在这里讨论的是对嵌入式linux系统的启动过 ...

  9. Springboot 启动信息：Generating unique operation named

    文章目录 Springboot 启动信息:Generating unique operation named 1.springboot 项目启动时,显示Generating unique operat ...

  10. 通过串口的启动信息反推VBIOS的内容

    需求:有一台没有PMON源码的龙芯3A5000 7A1000的机器,在不动任何软件的情况下获取到固件传递的VBIOS内容. 从串口打印中找到关键信息 vsp = 0x900000000f00f4c8 ...

最新文章

  1. 【Python学习笔记】输入raw_input()，特殊情况下也可以用input()
  2. 打工人得努力了呀！AI虚拟人都要入职了…
  3. adb install apk
  4. RedHat7.1 安装Oracle12102
  5. Find The Bone
  6. QT的QXmlDefaultHandler类的使用
  7. 【maven插件】flatten-maven-plugin ： 处理版本占位符
  8. Filter_细节_过滤器链(多个过滤器)
  9. 【51nod】1934 受限制的排列
  10. NotImplementedError: Cannot convert a symbolic Tensor报错与解决
  11. Java事务管理之Spring+Hibernate
  12. 程序员的工资普遍在20k以上
  13. 编译原理的first、follow、select
  14. Oracle 数据脱敏
  15. JavaScript模拟出一个input用于添加本地文件
  16. 使用FastReport进行基于富盛SBO程序开发框架的报表开发
  17. 改变蜡笔小新的眼睛颜色（对bmp图像的部分更改）
  18. VOCs废气处理设备-粤信环保
  19. 这个模型怎么划分网格？
  20. js清空浏览器cokie缓存_JS实现清除指定cookies的方法

热门文章

  1. java 毫秒转换秒_毫秒转换成时分秒 格式:HH:mm:ss Java兑现
  2. Fedora14 nfs配置 + tiny210 挂载nfs
  3. pytorch深度学习任务模板demo
  4. 初步实现免费下载百度文库word文档（只限纯文本文档）----------------（浏览器控制台执行js代码）
  5. android手游开发三维地图高清版,全球地图3D模拟器
  6. Origin复制图形格式
  7. 截止2021年7月中国有多少大学生？
  8. 八人抢答器讲解_八人抢答器PLC控制系统设计（最终版）最新版
  9. 在layui表格中插入时间插件
  10. 实验九 TCP 协议分析实验