中继器与AP的实现

这里我们假定中继器完成下面这样的一个功能：

Wired Network ---> Wireless Network ---> 上级无线路由器

即从外部插入一个网线，通过imx6UL上面的无线网卡将数据转发到上级的路由器上面，当然也可以完成下面这样的传送：

Wireless Network（AP mode） --> Wireless Network（Client） --> 上级无线路由器

即设立一个AP热点，相当于一个路由器，然后再将这个AP的数据通过另外一个无线网卡转发到上一级的路由器或者WLAN上面。

用图片来表示如下：

要完成这些功能，我们需要：

1. 驱动无线网卡
2. 建立AP热点
3. 其中一个wired或者wireless介入到上一级路由器或者WLAN中
4. 使用IPTables来对数据包进行转发

对于1，我们在前面已经完成，对于Wired Network访问WLAN我们也已经在前面完成。所以这篇我们将完成2与3，以及4。

AP热点的建立

建立AP热点，我们使用经典的Hostapd工具来完成，这个在OpenWRT中已经存在，直接选上，然后build即可。

Hostapd的使用

然后我们可以查看对应的使用帮助

root@(none):/# hostapd --help
hostapd: invalid option -- '-'
hostapd v2.5
User space daemon for IEEE 802.11 AP management,
IEEE 802.1X/WPA/WPA2/EAP/RADIUS Authenticator
Copyright (c) 2002-2015, Jouni Malinen <j@w1.fi> and contributorsusage: hostapd [-hdBKtv] [-P <PID file>] [-e <entropy file>] \[-g <global ctrl_iface>] [-G <group>] \<configuration file(s)>options:-h   show this usage-d   show more debug messages (-dd for even more)-B   run daemon in the background-e   entropy file-g   global control interface path-G   group for control interfaces-P   PID file-K   include key data in debug messages-t   include timestamps in some debug messages-v   show hostapd version

因此可以确定需要一个config文件，这个configuration file我们如下填写：

root@(none):/# cat /etc/hostapd_ori.conf
interface=wlan1
ssid=TonyOpenWRT
channel=9
hw_mode=g
ignore_broadcast_ssid=0
auth_algs=1
wpa=3
wpa_passphrase=TonyHo123456
wpa_key_mgmt=WPA-PSK
wpa_pairwise=TKIP
rsn_pairwise=CCMP

即我们创建一个SSID为TonyOpenWRT的热点， wpa_passphrase为密码，后面的为加密方式，然后还选择了channel，这个channel可以通过前面的iw list来查看，例如其中一个为：

               Frequencies:* 2412 MHz [1] (20.0 dBm)* 2417 MHz [2] (20.0 dBm)* 2422 MHz [3] (20.0 dBm)* 2427 MHz [4] (20.0 dBm)* 2432 MHz [5] (20.0 dBm)* 2437 MHz [6] (20.0 dBm)* 2442 MHz [7] (20.0 dBm)* 2447 MHz [8] (20.0 dBm)* 2452 MHz [9] (20.0 dBm)* 2457 MHz [10] (20.0 dBm)* 2462 MHz [11] (20.0 dBm)* 2467 MHz [12] (disabled)* 2472 MHz [13] (disabled)* 2484 MHz [14] (disabled)

后面的【】中的就是channel了。

建立AP

然后我们使用后台运行的方式启动hostapd，并且打开debug信息，便于我们查看：

root@(none):/# hostapd -B -d /etc/hostapd_ori.conf
random: Trying to read entropy from /dev/random
Configuration file: /etc/hostapd_ori.conf
rfkill: Cannot open RFKILL control device
nl80211: RFKILL status not available
nl80211: TDLS supported
nl80211: TDLS external setup
nl80211: Supported cipher 00-0f-ac:1
nl80211: Supported cipher 00-0f-ac:5
nl80211: Supported cipher 00-0f-ac:2
nl80211: Supported cipher 00-0f-ac:4
nl80211: Supported cipher 00-0f-ac:6
nl80211: Using driver-based off-channel TX
nl80211: Use separate P2P group interface (driver advertised support)
nl80211: interface wlan1 in phy phy1
nl80211: Set mode ifindex 9 iftype 3 (AP)
nl80211: Setup AP(wlan1) - device_ap_sme=0 use_monitor=0
nl80211: Subscribe to mgmt frames with AP handle 0xcfd5d8
nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0xcfd5d8 match=
nl80211: Register frame type=0x0 (WLAN_FC_STYPE_ASSOC_REQ) nl_handle=0xcfd5d8 match=
nl80211: Register frame type=0x20 (WLAN_FC_STYPE_REASSOC_REQ) nl_handle=0xcfd5d8 match=
nl80211: Register frame type=0xa0 (WLAN_FC_STYPE_DISASSOC) nl_handle=0xcfd5d8 match=
nl80211: Register frame type=0xc0 (WLAN_FC_STYPE_DEAUTH) nl_handle=0xcfd5d8 match=
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0xcfd5d8 match=
nl80211: Register frame type=0x40 (WLAN_FC_STYPE_PROBE_REQ) nl_handle=0xcfd5d8 match=
[  495.443813] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
nl80211: Add own interface ifindex 9
nl80211: if_indices[16]: 9
phy: phy1
BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits)
nl80211: Regulatory information - country=00
nl80211: 2402-2472 @ 40 MHz 20 mBm
nl80211: 2457-2482 @ 40 MHz 20 mBm (no IR)
nl80211: 2474-2494 @ 20 MHz 20 mBm (no OFDM) (no IR)
nl80211: 5170-5250 @ 160 MHz 20 mBm (no IR)
nl80211: 5250-5330 @ 160 MHz 20 mBm (DFS) (no IR)
nl80211: 5490-5730 @ 160 MHz 20 mBm (DFS) (no IR)
nl80211: Added 802.11b mode based on 802.11g information
Completing interface initialization
Mode: IEEE 802.11g  Channel: 9  Frequency: 2452 MHz
DFS 0 channels required radar detection
nl80211: Set freq 2452 (ht_enabled=0, vht_enabled=0, bandwidth=20 MHz, cf1=2452 MHz, cf2=0 MHz)* freq=2452* vht_enabled=0* ht_enabled=0
RATE[0] rate=10 flags=0x1
RATE[1] rate=20 flags=0x1
RATE[2] rate=55 flags=0x1
RATE[3] rate=110 flags=0x1
RATE[4] rate=60 flags=0x0
RATE[5] rate=90 flags=0x0
RATE[6] rate=120 flags=0x0
RATE[7] rate=180 flags=0x0
RATE[8] rate=240 flags=0x0
RATE[9] rate=360 flags=0x0
RATE[10] rate=480 flags=0x0
RATE[11] rate=540 flags=0x0
hostapd_setup_bss(hapd=0xcfcf50 (wlan1), first=1)
wlan1: Flushing old station entries
nl80211: flush -> DEL_STATION wlan1 (all)
wlan1: Deauthenticate all stations
nl80211: send_mlme - da= ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3
nl80211: send_mlme -> send_frame
nl80211: send_frame - Use bss->freq=2452
nl80211: send_frame -> send_frame_cmd
nl80211: Frame command failed: ret=-16 (Device or resource busy) (freq=2452 wait=0)
wpa_driver_nl80211_set_key: ifindex=9 (wlan1) alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=9 (wlan1) alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=9 (wlan1) alg=0 addr=(nil) key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=9 (wlan1) alg=0 addr=(nil) key_idx=3 set_tx=0 seq_len=0 key_len=0
Using interface wlan1 with hwaddr 94:0c:6d:7c:12:f6 and ssid "TonyOpenWRT"
Deriving WPA PSK based on passphrase
SSID - hexdump_ascii(len=11):54 6f 6e 79 4f 70 65 6e 57 52 54                  TonyOpenWRT
PSK (ASCII passphrase) - hexdump_ascii(len=12): [REMOVED]
PSK (from passphrase) - hexdump(len=32): [REMOVED]
random: Got 15/20 bytes from /dev/random
random: Only 15/20 bytes of strong random data available from /dev/random
random: Not enough entropy pool available for secure operations
WPA: Not enough entropy in random pool for secure operations - update keys later when the first station connects
GMK - hexdump(len=32): [REMOVED]
Key Counter - hexdump(len=32): [REMOVED]
WPA: Delay group state machine start until Beacon frames have been configured
nl80211: Set beacon (beacon_set=0)
nl80211: Beacon head - hexdump(len=62): 80 00 00 00 ff ff ff ff ff ff 94 0c 6d 7c 12 f6 94 0c 6d 7c 12 f6 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 0b 54 6f 6e 79 4f 70 65 6e 57 52 54 01 08 82 84 8b 96 0c 12 1y01 09
nl80211: Beacon tail - hexdump(len=65): 2a 01 04 32 04 30 48 60 6c 30 14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00 dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02 7f 08 00
nl80211: ifindex=9
nl80211: beacon_int=100
nl80211: dtim_period=2
nl80211: ssid - hexdump_ascii(len=11):54 6f 6e 79 4f 70 65 6e 57 52 54                  TonyOpenWRT     * beacon_int=100
nl80211: hidden SSID not in use
nl80211: privacy=1
nl80211: auth_algs=0x1
nl80211: wpa_version=0x3
nl80211: key_mgmt_suites=0x2
nl80211: pairwise_ciphers=0x18
nl80211: group_cipher=0x8
nl80211: SMPS mode - off
nl80211: beacon_ies - hexdump(len=10): 7f 08 00 00 00 00 00 00 00 40
nl80211: proberesp_ies - hexdump(len=10): 7f 08 00 00 00 00 00 00 00 40
nl80211: assocresp_ies - hexdump(len=10): 7f 08 00 00 00 00 00 00 00 40
WPA: Start group state machine to set initial keys
WPA: group state machine entering state GTK_INIT (VLAN-ID 0)
GTK - hexdump(len=32): [REMOVED]
WPA: group state machine entering state SETKEYSDONE (VLAN-ID 0)
wpa_driver_nl80211_set_key: ifindex=9 (wlan1) alg=2 addr=0x8dc74 key_idx=1 set_tx=1 seq_len=0 key_len=32
nl80211: KEY_DATA - hexdump(len=32): [REMOVED]broadcast key
nl80211: Set wlan1 operstate 0->1 (UP)
netlink: Operstate: ifindex=9 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
wlan1: interface state UNINITIALIZED->ENABLED
wlan1: AP-ENABLED
wlan1: Setup of interface done.
ctrl_iface not configured!

其中里面用到了加密时候需要的随机数，这个是使用内核中的random节点来生成的，所以我们在内核这两个还需要添加random驱动。

验证AP

在验证之前，我们需要给我们的这个网卡自己一个IP地址，因此直接：

root@(none):/# ifconfig wlan1 192.168.2.1
root@(none):/# ifconfig wlan1
wlan1     Link encap:Ethernet  HWaddr 94:0c:6d:7c:12:f6  inet addr:192.168.2.1  Bcast:192.168.2.255  Mask:255.255.255.0inet6 addr: fe80::960c:6dff:fe7c:12f6/64 Scope:LinkUP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1RX packets:131 errors:0 dropped:0 overruns:0 frame:0TX packets:106 errors:0 dropped:0 overruns:0 carrier:0collisions:0 txqueuelen:1000 RX bytes:20162 (19.6 KiB)  TX bytes:20954 (20.4 KiB)

然后我们打开手机查看是否可以看到我们的热点：

然后我们使用手动配置IP方式连接热点

连接完成后，我们可以看到已经连接的状态：

然后在手机上面可以Ping一把确定是否连通：

然后在iMX6UL上面也来ping一把这个手机：

root@(none):/# ping 192.168.2.111
PING 192.168.2.111 (192.168.2.111): 56 data bytes
64 bytes from 192.168.2.111: seq=0 ttl=64 time=90.952 ms
64 bytes from 192.168.2.111: seq=1 ttl=64 time=143.093 ms
64 bytes from 192.168.2.111: seq=2 ttl=64 time=4.508 ms
64 bytes from 192.168.2.111: seq=3 ttl=64 time=46.859 ms
64 bytes from 192.168.2.111: seq=4 ttl=64 time=2.539 ms
64 bytes from 192.168.2.111: seq=5 ttl=64 time=2.697 ms
^C
--- 192.168.2.111 ping statistics ---
6 packets transmitted, 6 packets received, 0% packet loss
round-trip min/avg/max = 2.539/48.441/143.093 ms

至此，基本的连接就好了，如果想要自动获取IP地址，那么我们还需要配置DHCPD。

wpa_supplicant的配置

前面我们使用其中一个网卡，配置好了AP，接下来我们使用另外一个Wireless作为上一级router的接入设备。这个可以参考我以前写的文章: Yocto i.MX6 (TQIMX6) (03) : wifi网卡的相关工具wpa_supplicant与dhcp
但是wpa_supplicant的版本升级后，和hostapd的使用基本一致起来，因此以前的使用方法稍微有些不同了。

配置

创建一个配置文件，写明需要接入的SSID，密码等信息：

root@(none):/# cat /etc/wpa.conf
ctrl_interface=/var/run/wpa_supplicant
network={ssid="XXX"proto=WPAkey_mgmt=WPA-PSKpairwise=TKIPgroup=TKIPpsk="PASSWORD"
}

其中XXX是路由器的热点名字， psk填写Password，加密方式TKIP需要根据实际情况填写，不明白可以看我以前的文章，或者直接man。

运行

先创建一个runtime目录：

root@(none):/# mkdir /var/run/wpa_supplicant

然后直接在后台运行：

root@(none):/# wpa_supplicant -B -iwlan0 -c /etc/wpa.conf
Successfully initialized wpa_supplicant
rfkill: Cannot open RFKILL contro[  172.506937] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
l device
[  172.527112] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29
[  173.083412] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
root@(none):/# [  174.937567] wlan0: authenticate with bc:d1:77:a0:4f:3c
[  175.073446] wlan0: send auth to bc:d1:77:a0:4f:3c (try 1/3)
[  175.082318] wlan0: authenticated
[  175.087051] rt2800usb 1-1.2.1:1.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[  175.098735] wlan0: associate with bc:d1:77:a0:4f:3c (try 1/3)
[  175.108018] wlan0: RX AssocResp from bc:d1:77:a0:4f:3c (capab=0x411 status=0 aid=5)
[  175.129960] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  175.136678] wlan0: associated
[  176.069997] IPv6: wlan0: IPv6 duplicate address fe80::7edd:90ff:feb2:73b1 detected!

验证

使用wpa_cli看查看连接的状态

root@(none):/# wpa_cli status
Selected interface 'wlan0'
bssid=bc:d1:77:a0:4f:3c
freq=2412
ssid=XXX
id=0
mode=station
pairwise_cipher=TKIP
group_cipher=TKIP
key_mgmt=WPA-PSK
wpa_state=COMPLETED
address=7c:dd:90:b2:73:b1
uuid=1e82e362-f927-544e-aa4d-1a229533944c

status为COMPLETED那么表示连接上了，然后我们获取IP地址，并尝试ping国内的某个网站：

root@(none):/# udhcpc -i wlan0
udhcpc (v1.24.1) started
Sending discover...
Sending select for 192.168.1.112...
Lease of 192.168.1.112 obtained, lease time 86400
/etc/udhcpc.d/50default: Adding DNS 192.168.1.1
/etc/udhcpc.d/50default: Adding DNS 0.0.0.0root@(none):/# ping meitu.com
PING meitu.com (42.62.69.156): 56 data bytes
64 bytes from 42.62.69.156: seq=0 ttl=42 time=44.499 ms
64 bytes from 42.62.69.156: seq=1 ttl=42 time=44.956 ms
64 bytes from 42.62.69.156: seq=2 ttl=42 time=43.122 ms
64 bytes from 42.62.69.156: seq=3 ttl=42 time=43.387 ms
64 bytes from 42.62.69.156: seq=4 ttl=42 time=46.467 ms
64 bytes from 42.62.69.156: seq=5 ttl=42 time=46.267 ms
64 bytes from 42.62.69.156: seq=6 ttl=42 time=43.843 ms
^C
--- meitu.com ping statistics ---
7 packets transmitted, 7 packets received, 0% packet loss
round-trip min/avg/max = 43.122/44.648/46.467 ms

至此，我们就完成了基本的配置工作。

OpenWRT中使用无线网卡做中继器与AP热点相关推荐

已解决关于vmware搭openwrt旁路由无线网卡设备无法上网
macbook中vmware装了个openwrt旁路由,桥接到本机的无线网卡,经测试发现: 1.宿主机改网关后,可通过op上网和科学 2.其他无线设备改网关不能上网,但是可以ping通op,上op的网 ...
怎样用笔记本的无线网卡做一个AP 实现笔记本做wifi热点供手机、平板电脑wifi上网而不用无线路由器
怎样用笔记本的无线网卡做一个AP 实现笔记本做wifi热点供手机.平板电脑wifi上网而不用无线路由器首先前提是:笔记本要带无线网卡的! 利用WIndows 7的hostednetwork创建无线 ...
WIN7下使用无线网卡共享网络（利用笔记本无线网卡做无线AP）
现在手机上网非常方便,躺在被窝里,坐在马桶上都能玩,但在某些情况下没有无线网络环境,但有有线网络环境,这时若你能有台笔记本,则可以把你笔记本的无线网卡当网关来使. 应用环境: 1.有能连接因特 ...
【转】Win10系统怎么设置无线做AP热点_win10设置无线为ap热点的步骤
转自:http://www.win7zhijia.cn/win10jc/win10_33126.html 在win10系统中,默认情况下无线网卡大部分都用于STA模式,但是有时候需要将无线网卡的工作模 ...
让无线网卡同时工作在 AP 和 STA 模式
这个帖子里的方法有点过时了,不推荐继续使用. 有的时候会碰到这么一种情况,带着电脑和手机出去蹭网,无奈只有一个账号,手机上了电脑就没得用了,电脑用了手机就上不了网.如果能用电脑连接 Wifi 然后再开 ...
ap模式和sta模式共存_让无线网卡同时工作在 AP 和 STA 模式
这个帖子里的方法有点过时了,不推荐继续使用. 有的时候会碰到这么一种情况,带着电脑和手机出去蹭网,无奈只有一个账号,手机上了电脑就没得用了,电脑用了手机就上不了网.如果能用电脑连接 Wifi 然后再开 ...
openwrt下无线网桥设置，bridge AP模式
** bridged AP vs route 模式 ** bridged AP 模式相对于上一级路由器的 DHCP server 和 openwrt 无线路由器对下面的接入点是透明的各个接入点通过 ...
无线网卡实现AP 热点功能，共享Internet连接设置
1. 首先确定无线网卡是否支持AP热点功能 windows 命令提示符中输入 "netsh wlan show drivers". 命令输出中,有一行""支持的 ...
完整适配LUCI界面的Openwrt中EC20的QMI拨号
目前4G模块应用已经非常普及,跟之前的3G不同,3G基本使用ppp拨号,usbserial驱动,Linux内核自带支持,此应用非常简单. 4G模块由于速率较高,usbserial驱动性能满足不了,因此 ...

OpenWRT中使用无线网卡做中继器与AP热点